Craftsman 88704 Support Question
Craftsman 88704 Support Question
Find answers below for this question about Craftsman 88704 - 123cc 4 Cycle Single Stage Snow Thrower.Need a Craftsman 88704 manual? We have 1 online manual for this item!
Question posted by igordm7 on September 24th, 2017
The Length Of The Drive Belt Auger Craftsman 88704?
the length of the drive belt auger craftsman 88704?
Current Answers
Answer #1: Posted by BusterDoogen on September 26th, 2017 9:52 AM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,417
Member since:
October 30th, 2011 Points: 28,565,417
- .5 (1/2)-in Top Width
- 35-in Length, go here to see the part: MTD Genuine OEM Part #954-0101A
- Replaces Part Number 954-0235
- Replaces Part Number OEM-754-0101A
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Craftsman 88704 Manual Pages
Operation Manual - Page 1
Operator's Manual
CRRFr MRN
21" SNOW THROWER
Model No. 247.88704
CAUTION: Before using this product, read this manual and follow all
safety rules and operating instructions.
Visit our website: www.craftsman.com
FORM1/0. 769-05022
6/18/2009 o SAFETY ASSEMBLY OPERATION MAINTENANCE PARTS LIST
o ESPANOL
Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A.
Operation Manual - Page 2
...Tire replacement or repair caused by fuel determined to auger blades, skid shoes, shave plate, shear pins, spark plug, air cleaner, belts, and oil filter.
Tire or wheel replacement or ...state. This warranty applies only while this Craftsman snow thrower fails due to a defect in the United States for :
• Expendable items that bend the auger, frame or crankshaft. Engine (fuel ...
Operation Manual - Page 3
... Stateof California to stop the machineand disengagethemquickly. Planyour snow-throwingpatternto avoiddischargeof materialtoward roads,bystandersand the like.
Alwayswear ...,newspapers,sleds,boards,wires and other foreignobjects,whichcouldbe trippedoveror thrownby the auger/ impeller.
Neverallowchildrenunder 14 yearsof age to be used.
PREPARATION
Thoroughlyinspectthearea...
Operation Manual - Page 4
...vibrateabnormallys, top the engine, disconnectthe spark plugwire and groundit againstthe engine. OPERATION
• Do not puthandsor feet near rotatingparts,in the auger/impeller housingor chuteassembly.Contactwith the rotatingpartscan amputatehandsand feet.
• Theauger/impellercontrol leveris a safetydevice.Neverbypass its operation.Doingso makesthe machineunsafeand may cause personalinjury...
Operation Manual - Page 5
...workingproperlyand not wornexcessively.Failureto do not modifyengine in any )
If a sparkattester is used, it to operateat unsafespeeds.Nevertamperwithfactory setting of auger/impeller. Checkcontrolleversperiodicallyto verifythey engageand disengage properlyand adjust,if necessary.Referto the adjustment sectioninthis operator'smanualfor instructions. to keepthe machinein safe workingcondition...
Operation Manual - Page 6
...-- SAFETY SYMBOLS
This pagedepictsand describessafetysymbolsthat mayappear on this product. ROTATING BLADES Keep hands out of inlet and discharge openings inside
while
machine
is running .
ROTATING AUGER Do not put hands or feet near rotating parts, in a poorly monoxide, an odorless and deadly gas. housing or chute assembly. WARNING--THROWN OBJECTS This...
Operation Manual - Page 7
...%ethanolor 15%MTBE(MethylTertiaryButyl Ether)can be used. NOTE:Referencesto rightor left sideof the snowthrowerare determinedfrom behindthe unit in the operatingposition(standing directlybehindthe snow thrower,facingthe handlepanel).
2. Cut the cornersof thecarton and lay the sidesflat on the ground. Removeand discard all packinginserts.
2. J • Be carefulnotto spillfuel whenrefueling...
Operation Manual - Page 8
...can causeseriousenginedamageand void the productwarranty.
. See
Figure3. Loosenthewing knobfoundon the left sideof the chuteassemblyand pivot the upperchute upwardor downwardto the desired pitch.Retightenthe wingknobbeforeoperatingthesnow thrower.
Removetheoil fillercap/dipstickand wipethe dipstickclean. ADJUSTMENTS
Chute Assembly
The pitch of thechute assemblycontrolstheangle at whichthe...
Operation Manual - Page 10
releaseit to add fuel.
Removethe key whenthe snow throwerisnot inuse.
NOTE:Do notturn the key in propellingthe snowthroweras they comein contactwith the pavement.
Meets ANSi Safety Standards
CraftsmanSnowThrowersconformto the safetystandardof the AmericanNationalStandardsInstitute(ANSI).
10 AUGER CONTROL
Locatedon the upper handle,the augercontrolhandle is usedto startthe ...
Operation Manual - Page 11
...THE AUGERS
Engagethe augerby squeezingtheauger controlagainstthe upper handle.Releasethe controlto stop the auger. ENGAGING THE DRIVE
Lift up slightlyon the handleto allowthe rubberpaddleson the auger to...THE ENGINE
1. SHAVE PLATE
Theshaveplate maintainscontactwith the pavementas the snow throweris propelled,allowingsnowclose tothe pavement'ssurfaceto be surethe impellerbladeshavestopped rotating...
Operation Manual - Page 15
... Inspectthe spark plug.If itiswet, cleanoff any oil before
re-installing. 4.
Thentip the snow
throwerbackuntil it is pulled. 6. f
NOTE:Wheninstallinga newsparkplug,tighten 1/2-turnafter the
\
spark ...machineon a levelsurface.The wheels,shaveplateand auger paddlesshouldall contactthe levelsurface.Notethat if the shaveplateis adjustedtoo high,snow mayblowunder theauger housing.If the ...
Operation Manual - Page 16
... referto Figure15:
Control Handle
/
/
/
/
J
Figure13
Testthe snow throwerto seeif there is a noticeabledifference.If after theadjustmentto the controlcablethe augerstill hesitateswhen rotating,see BeltReplacementfor instructionson replacingthebelt.
Figure15
1. BELT REPLACEMENT
Auger Drive Belt 1. Chute Assembly Referto the Assemblysectionfor instructionson adjustingthechute assembly...
Operation Manual - Page 17
....See Figure16. Removethe four carriagebolts and hexlock nuts which attachit to the snowthrowerhousing. . i/." REPLACING SHAVE PLATE The shaveplateis attachedto the bottomof the auger housingand issubjectto wear.It shouldbe checkedperiodicallyT. Removethe existingrubberpaddlesby unscrewingthe self-
Ask for part #731-1033.
17 hereare two wearingedgesand the shaveplatecanbe reversed...
Operation Manual - Page 18
...) of the snowseasonwhenthe last possibilityof snowis gone,the equipmentneedsto be storedproperly.Followstorageinstructionsbelowto ensuretop performancefrom the snowthrowerfor manymoreyears. PREPARING ENGINE
PREPARING SNOW THROWER
Enginesstoredover30 days need to be drainedof fuel to rustprooftheequipment.Using a light oil or silicone,coat theequipment,especiallyanychains, springs,bearingsand...
Operation Manual - Page 19
.... Clean chuteand insideof augerhousingwith clean-outtool or stick.
2.
Get a personalized maintenance plan for your other product manuals online.
Enginefails to selfpropel
Auger continuesto rotate
1. Keynot insertedall the way. 4. Fuelline blocked,or stale fuel. 3. Ventin gascap plugged.
1.
Augerdrive beltlooseor damaged. 1. Augercontrol cableoutof adjustment.
Foreignobject...
Operation Manual - Page 21
Craftsman Snow Thrower IViodel 247.88704
684-04236A Shroud
D=
WO
2. 710-04669
HexScrew,10-16x .625
3. 710-1090 4. 712-04063
Hex FlangeScrew,5/16-18x 1.25 FlangeLock Nut,5/16-18
5. 710-1882 6. ...
Operation Manual - Page 23
Craftsman Snow Thrower IViodel 247.88704...-0625
PushCap, 1/2 ShoulderScrew, CableRoller
33. 984-04253-0637 Auger Assembly2, 1"
34. 750-04757
LHSpacer
35. 750-04758...33x 1.12 Hex LockNut, 1/4-28
41. 684-04227-0721 Auger HousingAssembly,21"
42. 710-0896 43. 735-04033
HexScrew,1/4-...16
48. 750-04297B NS 753-04472
Spacer,.875x .320xl.027 Auger ReplacementKit (Inc.42-44)
23 J 726-0233 12. 926-0154...
Operation Manual - Page 25
...95 951-10370
96 951-10957
-- 951-10952A
70
--
79
--
CarburetorInsulatorGasket
81
--
CylinderHeadGasket
79
-- Packing
84
-- External HeadCoverGasket CarburetorInsulatorGasket
81
--
Craftsman Engine IViodel ZS161-JWA For Snow Thrower IViodel 247.88704
m
D=
OO
1 710-04920 FlangeBolt
8 715-04092 Dowel Pin,7 x 14
12 714-04074 16 710-04906 17 736-04440
GovernorArm...
Operation Manual - Page 26
...ThrottleShaft DustSeal
94 1951-10949A CylinderHeadAssembly
40
-- intakeValveSpringSeat
58
--
Complete
76
--
Bearing
15
--
HeadCoverGasket
76
-- Craftsman Engine IViodel ZS161=JWA For Snow Thrower IViodel 247.88704
-- 951-11097
D=
O
CrankcaseKit
14
--
15
--
84
--
-- 951-11096
Bearing CrankcaseComplete Oil Seal CrankshaftKit
6
--
CrankshaftAssembly
14...
Operation Manual - Page 27
T
USEE85 ORFUEL.......... Craftsman Snow ThrowerModel 247.88704 777533124
1. DISENGAGCELUTCHLEVERSS, TOPENOiHE, AHDREiYIAIBHEHIHDHANDLEUSNTILALLMOVING PARTSHAVESTOPPEBDEFORUEHCLOGGIONGR SERViCiNMGACHINE.
3.TOAVOIDTHROWONBJECTiSNJURiESN, EVER DIRECDTISCHARGAETBYSTANDEURSSEEXTRA CAUTIOWNHENOPERATINOGNGRAVESLURFACES.
4, READOPERATORM'SARUAL.
777X43688
...D..O...H...O. CONTAiNiNGMORE THAN10...
Similar Questions
where is the carborator on this machine
(Posted by 22guapo 8 years ago)
Transmission Drive Belt Replacement On Craftsman Zts6000
How Do You Replace A Drive Belt On A Craftsman Zts 6000 Zero Turn Mower
How Do You Replace A Drive Belt On A Craftsman Zts 6000 Zero Turn Mower
(Posted by JAXGEP 9 years ago)
What Kind Of Oil Does A Craftsman 4 Cycle Snow Blower Use
(Posted by Anonymous-48784 12 years ago)
When Engage Auger Snow Thrower Starts Making A Noise
Have my Craftsman Porfesional 30" snow thrower for a year. I had to replace the clutch cable, after ...
Have my Craftsman Porfesional 30" snow thrower for a year. I had to replace the clutch cable, after ...
(Posted by irandine 12 years ago)