Home » Craftsman » Lawn Mowers » Craftsman 28928

Craftsman 28928 Support Question

Find answers below for this question about Craftsman 28928 - YT 4000 24hp 46" Yard Tractor.
Need a Craftsman 28928 manual? We have 1 online manual for this item!

Craftsman Overview Questions Manuals Reviews Videos Research

Question posted by noicause on April 7th, 2014

Tractor 247.288842 Replace Clutch Engagement Cable

Craftsman 42" lawn tractor model needs the clutch cable replaced. The directions enclosed with then cable are useless.

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Craftsman 28928 Manual Pages

Operation Manual - Page 2

..., or product label replacement. Warranty 2 Safety Rules 3 Product Specifications 6 Assembly/Pre-Operation 7 Operation 9 Maintenance Schedule 17 Maintenance 17 Service and Adjustments 21 Storage 28 Troubleshooting 29 Sears Service Back Cover Craftsman Riding Equipment Warranty: Lawn Tractors, Garden Tractors, Zero Turn Riders CRAFTSMAN TWO YEAR FULL...

Operation Manual - Page 8

...replacing motion and mower blade drive belts in the Operation section of other people and objects. Roll tractor forward off the skid. Remove banding holding the deflector shield up against tractor...keepers. / Check wiring. Be sure the area in "transmission engaged" position (see that you learn how to operate your tractor, check to see "TO TRANSPORT" in the Service and ...

Operation Manual - Page 9

... minor or moderate injury. These symbols may appear on your tractor or in damage to the tractor and/or engine. CAUTION when used to identify safety information ...ON ENGINE START PARKING BRAKE MOWER HEIGHT MOWER LIFT LIGHTS ON FUEL t BATTERY REVERSE FORWARD CRUISE CONTROL CLUTCH/BRAKE PEDAL @@®@@ ATTACHMENT CLUTCH DISENGAGED ATTACHMENT CLUTCH ENGAGED DANGER, KEEP HANDS AND...

Operation Manual - Page 10

... with the engine off . (J) CRUISE CONTROL LEVER - Used for pushing or slowly towing the tractor with the locations various controls and adjustments. Turns the headlights on and off . (P) SERVICE REMINDER/HOUR METER - Used for the engine and mower. 10 Used to engage the mower blades, or other attachments mounted to raise and lower the...

Operation Manual - Page 11

... controlled by the operator to leave the seat without first setting the parking brake will hold tractor secure. STOPPING MOWER BLADES - TO MOVE FORWARD AND BACKWARD The direction and speed of movement is depressed. (_) Attachment Clutch (t'_) Disengaged Position Engage Position GROUND DRIVE. Slowly depress forward (K) or reverse (L) drive pedal to stop ground drive, depress...

Operation Manual - Page 12

.... Start mower blades by the operator to the blade tip with the engine not running and the attachment clutch engaged will shut... prevent the engine from the ground to leave the seat with tractor on slopes, rough tertian or while trimmimg or turning. •...heights are slightly off the ground. For healthier and better looking lawns, mow often and after moderate growth. • For best ...

Operation Manual - Page 13

.... tion. 3. When use if you are certain no longer needed, turn ignition key counterclockwise to start movement. 5. Use an appropriate means of tractor. 1. tion with the attachment clutch engaged will enter the mowing area. 1. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it...

Operation Manual - Page 14

...carburetor cleaner products in the transmission engaged position. 2. To service engine and mower, see the Maintenance section in ...clutch to choke position. Do not add oil until the fuel lines and carburetor are recommended by and comply with tractor...disengaged position. 4. in quantities that the engine or mower needs servicing. IMPORTANT: When operating in any spilled oil or...

Operation Manual - Page 15

... position and hold for service or replace- ment, it is running , move throttle control to operating position. 3. Once rough running . wheel control in engaged position (See "TO TRANSPORT" in... may need to several seconds to be warmed up . When engine starts, leave throttle control in cold weather, the transmission follows: should be purged before operating the tractor. 1....

Operation Manual - Page 18

... slow leaks, tire sealant may cause tire damage. BLADE CARE For best results mower blades must be serviced. (See "TO CHECK BRAKE" in the Service and ...clutch engaged, any maintenance. Install and tighten blade bolt securely (45-55 Ft. torque). iMPORTANT: treated. Blade Bolt (Special) Center Hole Assembly ROS "ON" Position Engine "ON" Position (Normal Operating) BATTERY Your tractor...

Operation Manual - Page 19

...inward and turning clockwise until bright. 4. Clean terminals and battery cable ends with plain water and dry. 3. Replace belts if they will drain more frequently to clean fan or transmission... yellow cap from tractor. 2. Reinstall battery (See "REPLACING BATTERY" in one year. TRANSAXLE PUMP FLUID The transaxle was sealed at least once a year if the tractor is hot. Should...

Operation Manual - Page 21

... lift links are pointing forward before sliding mower under tractor. 03042tex 21 TO INSTALL MOWER Be sure tractor is spring loaded. Make sure the blades and all moving parts have completely stopped. 5. Place attachment clutch in contact with plug. Remove clutch cable spring (Q) from tractor and hook the clutch spring (Q) into the cable guide on lift lever when changing position...

Operation Manual - Page 22

... LINKS (C) - Insert rod end of link assembly through front hole in the Operation section of tractor. 7. If necessary, adjust gauge wheels before operating mower as shown in tractor front suspension bracket (F). ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Push clutch cable housing guide (P) into bracket, slide collar (L) onto guide and secure with washer and retainer spring...

Operation Manual - Page 24

... transmission input pulley and over the steering plate (F) and above clutch brake pedal shaft (G). 2. BELT INSTALLATION - 1. Pull belt toward rear of left footrest. Mandrel TO REPLACE MOTION DRIVE BELT Park the tractor on bottom side of tractor. Remove mower (See "TO REMOVE MOWER" in this section of tractor, off both mandrel pulleys and idler pulleys 2. Work belt...

Operation Manual - Page 25

...4. If "jumper cables" are not adjustable. The other vehicles. Weak or Dead Battery Fully Charged Battery Washers Retaining Ring Axle Cover I _--xSquare Key (Rear Wheel Only) 25 engaged" position. Do not lose). 3. If your tractor battery to start... charged battery. 3. If the rear wheels rotate, then the brake needs to be a 12 volt system. Replace axle cover.

Operation Manual - Page 26

...need adjustment, see engine manual. Slide terminal cover (C) over terminal. 5. The fuse holder is necessary, see engine manual. When replacing hood, be necessary. If adjustment is located behind the dash. However, minor adjustment may cause your tractor... tractor. Headlight Wire Connector Positive (Red) Cable TO REPLACE HEADLIGHT BULB 1. Close hood. First connect RED battery cable ...

Operation Manual - Page 27

...tractor for storage, do not store battery directly on stabilizer container. Clean entire tractor (See "CLEANING" in the tank inside a building where fumes may reach an open flame or spark. Inspect and replace belts, if necessary (See belt replacement... corrosion and power leakage during long periods of storage, battery cables should be disconnected and battery cleaned thoroughly (see "TO CLEAN...

Operation Manual - Page 28

.... 7 Check/replace ignition switch. 8 Check/replace solenoid or starter. 9 Contact a Sears or other qualified service center. 28 TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM Will not start Hard to start Engine will not turn over CAUSE 1 Out of adjustment. 1 Brake pedal not depressed. 2 Attachment clutch is engaged. 3 Weak...

Operation Manual - Page 29

... Carburetor out of adjustment. 15 Engine valves out of mower housing. 4 Clean/replace air filter. 5 Check oil level/change oil. 6 Clean and regap or change spark plug. 7 Replace fuel filter. 8 Empty fuel tank and refill tank witlfresh, clean gasoline. 9 Empty fuel tank and carburetor, refill tank with attachment clutch engaged Faulty operator-safety control system.

Operation Manual - Page 31

... "OFF" Engine dies when tractor is shifted into reverse CAUSE CORRECTION 1 Bad battery cell(s). 2 Poor cable connections. 1 Replace battery. 2 Check/clean all connections. 3 Faulty regulator (if so equipped). 4 Faulty alternator. 3 Replace regulator. 4 Replace alternator. 1 Freewheel control in "disengaged" position. 1 Place freewheel control in "engaged" position. 2 Motion drive belt...