Craftsman 28924 Support Question
Craftsman 28924 Support Question
Find answers below for this question about Craftsman 28924 - YT 3000 21 HP/46" Yard Tractor.Need a Craftsman 28924 manual? We have 1 online manual for this item!
Question posted by buddy85885 on April 27th, 2015
Tractor Was Working Fine Got Off Moved The Seat Back Now Its Starts And Runs But
when you but it in forward or reverse or engage the blade it stalls out
Current Answers
Answer #1: Posted by TommyKervz on April 28th, 2015 1:13 AM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,813
Member since:
January 10th, 2013 Points: 17,776,813
Related Craftsman 28924 Manual Pages
Operation Manual - Page 3
...and working.
• Slow down and behind before turning. • Never leave a running machine unat- tended. dation for wheel weights or counterweights. • Keep machine free of the tractor.
...8226; Disengage blades when not mowing. Too heavy of alcohol or drugs. • Watch for all instructions on the machine and in reverse unless absolutely
necessary. tal starting . •...
Operation Manual - Page 5
...blade
or wear gloves, and use a nozzle lock-open device. • Iffuel is in safe working...Mower blades are sharp. Ifthe tires lose traction, disengage the blades and proceed slowly straight down the slope.
• If machine stops while going uphill, disengage blades, shift into reverse...who have to be run over or backed
... on the slope.
• Avoid starting, stopping, or turning on a slope...
Operation Manual - Page 6
...repair scheduling. nance" and "Storage" sections of this tractor. Here's what's included in the Agreement:
•... other major home items, in effective working order by the operator. Once you ...on making a smart purchase.
Champion RC12YC (Gap: .030")
Forward: Reverse:
0- 5.5 0- 2.4
3 Amps Battery 5 Amps Headlights
Amp/... System:
Battery:
Blade Bolt Torque:
2.50 Gallons Unleaded Regular
...
Operation Manual - Page 7
... desired position and release adjustment handle.
7
Seat
Label
Terminal
Terminal
TO ADJUST SEAT
Grasp adjustment handle (A) and pull up, slide seat to raised position. at 6-10 amps. (See "BATTERY" in the operating position (seated behind the steering wheel). Check for shipping purposes.
Remove all four panels
of your tractor must be tightened securely. Remove end...
Operation Manual - Page 8
...tractor forward off the skid. Continue with all instructions in the Operation section of this Quality Product. CHECK BRAKE SYSTEM
After you start the engine.
/ Be sure brake system is operating properly. have been
/ No remaining loose parts in carton.
/Battery
is properly prepared and
charged.
/ Seat is in "transmission engaged...for replacing motion and mower blade drive belts in ...
Operation Manual - Page 9
...REVERSE OPERATION
SYSTEM (ROS)
ENGINE ON ENGINE START
PARKING
_ E21 { j.,
BRAKE
MOWER HEIGHT
MOWER LIFT
LIGHTS ON
FUEL
BATTERY
REVERSE
FORWARD
CRUISE CONTROL
CLUTCH/BRAKE PEDAL
®@®@@
ATTACHMENT CLUTCH DISENGAGED
ATTACHMENT CLUTCH ENGAGED...in literature supplied with the product.
CAUTION when used to the tractor and/or engine. HOT SURFACES indicates a hazard which , if...
Operation Manual - Page 10
... or other powered attachment while in reverse.
(H) LIGHT SWITCH - Disengages
transmission for starting
and stopping the engine.
(G) REVERSE OPERATION
SYSTEM
(ROS) "ON" POSITION - Save this manual for starting and controlling engine speed.
(E) ATTACH M ENT CLUTCH LEVER =Used
to engage the mower blades, or other attachments mounted to your tractor.
(B) CLUTCH/BRAKE
PEDAL -Used for...
Operation Manual - Page 11
When engine is running , hot engine exhaust gases may cause "browning" of any adjustments or repairs. Make sure parking brake will hold tractor secure.
• Move motion control lever (J) to leave the seat without first setting the parking brake will cause the battery to "STOP" position and remove key. STOPPING
MOWER BLADES • To stop ground drive...
Operation Manual - Page 12
... a flat level surface.
1.
TO MOVE FORWARD AND BACKWARD The direction and speed of movement is at the desired cutting height in operating position. Start tractor with the
engine running . Gauge wheels then keep the deck in proper position to desired cutting height (See "TO ADJUST MOWER CUTTING HEIGHT" in the
seat to
desired position. Tighten
securely. 3. Repeat...
Operation Manual - Page 13
... leverto neutral position. With engine running, turn the ignition key clockwise to allow reverse operation with the attachment
engaged. Slowly move motion control lever to start movement. 5.
Freewheel control is located at the back of this manual. • Choosethe slowest speed before and while
backing. 4. Raise attachment lift lever to tractor (rope, cord, etc.).
Use the...
Operation Manual - Page 14
...on seat in cold weather, the transmission should be warmed up . If the engine does not start , move the throttle
• Fill fuel tank to choke position. WARM WEATHER above 3000 feet...tractor is reached. Place motion control lever in neutral
CHECK ENGINE OIL LEVEL
The engine in quantities that can
now be used . Do not run roughly. Once rough
running begins, immediately move...
Operation Manual - Page 15
.... With motion control lever in the tractor seat, start engine. See "TO LEVEL MOWER HOUSING" in the tractor seat, start engine. Have the cut relatively high;
the second to reverse position. Allow grass to dry before operating the tractor. 1. PURGE TRANSMISSION
A
_CAUTION:
Never engage or disengage
freewheel lever while the engine is running, move throttle control to slow position...
Operation Manual - Page 17
... results mower blades must be serviced. (See "TO CHECK BRAKE" in the seat.
NOTE: Protect your
warranty. Install new blade with the ignition switch in the engine "ON" position and the attachment clutch engaged, any maintenance. Special blade bolt is running with star on a level, dry concrete or paved surface, then brake must be purchased from your
tractor...
Operation Manual - Page 18
...Determine temperature
range expected
before starting in increased oil consumption when used for 1 hour. All oil must meet API service classification SG-SL
• Be sure tractor is on level surface.
... fan and cooling fins should be sure fan blades
are not adjustable. To prevent possible damage to avoid possible engine damage from running or while the transmission is hot. Should the...
Operation Manual - Page 20
... (Blade Engage) is clear.
7. Release the lock collar to lock the adapter on your lawn, near enough to remove grass, leaves and trash from the nozzle washout port.
10. Movethetractor'sPTO(BladeEngage) to a dry area, preferably a concrete or paved area. Turn the ignition key to the STO P position to keep water out. Move the tractor...
Operation Manual - Page 21
Make sure the blades and all moving parts have completely stopped. 6. Remove clutch cable spring (Q) from mower remove retainer spring and washer.
7. remove retainer springs and washers. Al_ CAUTION: After rear lift links are pointing forward before sliding mower under right side of tractor.
Lower attachment lift lever to be spring loaded.
TO REMOVE MOWER
1. Roll belt off...
Operation Manual - Page 25
... additional clearance is needed to
get to adjustment bolt, move forward or backward.
3. Loosen the adjustment bolt. 2. TO START ENGINE WITH WEAK BATTERY
A_,WARNING:
Lead-acid batteries...
Start engine and move motion control
lever until satisfied.
After above steps
until tractor does not move mower deck
height to good chassis ground, away from the fully charged battery. 2. Start ...
Operation Manual - Page 26
...RED battery cable and carefully remove
battery from starting. • Check wiring.
Close hood. Hood... hex bolt and keps nut as shown. Tighten securely. Seat Pan ----.._
INTERLOCKS AND RELAYS
Loose or damaged wiring may be...the Repair Parts manual. Connect BLACK grounding cable to run poorly, stop running, or prevent it from tractor. 3. Raise hood. 2. Remove bulb holder from...
Operation Manual - Page 27
...of storage, battery cables should be stored for a period of time, clean it run until the fuel lines and carburetor are still warm.
27
Also, alcohol blended fuels (called gasohol ...manual. 4.
Inspect moving parts for winter
storage. tank and carburetor ENGINE OIL
Do not empty the gas if using ethanol or methanol) can starts to rust. TRACTOR
Remove mower from tractor for storage, do ...
Operation Manual - Page 29
...(s). TROUBLESHOOTING CHART: See appropriate section in manual unless directed to 1
run when operator leaves seat with fresh gasoline and replace fuel filter.
10 Connect and tighten spark...refill tank with
attachment
clutch
engaged
Faulty operator-safety control system. Engine continues to Sears service center
PROBLEM
CAUSE
CORRECTION
Engine clicks but will not start
Loss of power
1 ...
Similar Questions
My Father Has One Of These And It Has Worked Fine For Four Years. I Just It New
(Posted by Kensullivan93 9 years ago)
Craftsman Yt 3000 Starts But Dies When Ignishon Released
(Posted by FaLik 9 years ago)
Yt 3000 21 Hp Yard Tractor By Craftsman How To Clean The Carburetor
(Posted by jobyproo 9 years ago)
Craftsman Lts2000 Worked Fine For Two Years. Died While In Use, Now Won't Start
(Posted by Anonymous-36394 12 years ago)
The Craftman 46' Yard Tractor #07128852 What's The Price?
(Posted by norden32 13 years ago)