Craftsman 10137 Support Question
Craftsman 10137 Support Question
Find answers below for this question about Craftsman 10137 - 1/2 in. Corded Hammer Drill.Need a Craftsman 10137 manual? We have 1 online manual for this item!
Question posted by j21521rivera on January 16th, 2013
10137 Electrical Switch Replacement
I need to purchase a Drill, model 10137 electricla switch...
Current Answers
Related Craftsman 10137 Manual Pages
Operation Manual - Page 1
... Estates, IL 60179 USA Visit the Craftsman web page: www.sears.com/craftsman
983000-753 6-14-06 (REV:01)
Save this product. HAMMER DRILL VARIABLE SPEED/REVERSIBLE
DOUBLE iNSULATED
Model No. 315.101370
A WARNING: To reduce the risk of injury,
the user must read and understand the
operator's manual before using this manual...
Operation Manual - Page 2
... free of purchase. Sears, Roebuck and Co., Dept. 817 WA, Hoffman Estates, IL 60179
This tool has many features for commercial or rental purposes, this Craftsman tool fails to give complete satisfaction within one year from state to maintain and operate. [] Warranty ...
2
[] Introduction ...
2
[] General Safety Rules ...
3-4
[] Specific Safety Rules ...
4
[] Symbols ...
5-6
[] Electrical...
Operation Manual - Page 3
... any other condition that have the power tool repaired before turning the power tool on invites accidents.
[] Remove any adjustments, changing accessories, or storing power tools. Keep cord away from moving parts, breakage of electric shock if your application. Ensure the switch is in all instructions. The correct power tool will increase the risk of the warnings...
Operation Manual - Page 4
... of moving parts, binding of moving parts, breakage of the power tool is maintained.
_IL WARNING! Check for and remove all nails from chemically-treated lumber. A wire gauge size (A.W.G.} of at your extension cord is damaged should be properly repaired or replaced by a qualified repair person using this rule will reduce the risk...
Operation Manual - Page 6
...completely the operator's manual. Always use only identical replacement parts. SAVE THESE INSTRUCTIONS
SERVICE
Servicing requires extreme care...
,_ WARNING"
The operation of any power tool can result in foreign objects being thrown into...shields, or a full face shield when needed. Thefollowingsignalwordsandmeaningasreintendedto explainthe levelsofriskassociatedwiththis product. SYMBOL
SIGNAL...
Operation Manual - Page 7
Always use . ELECTRICAL CONNECTION
This tool has a precision-built electric motor. If your nearest authorized service center for repair. An undersized cord will overheat.
A WARNING: Check extension cords before each
use original factory replacement parts when servicing. All exposed metal parts are working with a tool, use tool with double insulation requires extreme care and ...
Operation Manual - Page 8
...Ibs.
Blows Per Minute (BPM 0-16,000/min. AUXILIARY HANDLE
DRILLING/HAMMER MODESELECTOR
LEVELS
DEPTH GAUGE ROD
DEPTH GAUGE CLAMP
KEYLESS SPINDLE LOCK
CHUCK
BUTTON
VARIABLE SPEED SWITCH
LOCK-ON BUTTON
DIRECTIONOF ROTATION (FORWARD/
REVERSE)
LIVETOOL INDICATOR
Fig. 1
PRODUCTSPECiFICATiONS Chuck 1../.2..i.n...Keyless
Switch Variable Speed/Reversible No Load Speed 0-1,000/rain.
Operation Manual - Page 9
... alteration or modification is the number of impacts per minute that the tool delivers in the packing list are replaced. Failure to do not operate
this tool until you to modify this tool or
create accessories not recommended for use .
HAMMER SPEED Your hammer drill has a hammer speed of bit rotation. Blows Per Minute is misuse and could...
Operation Manual - Page 10
...with side shields when operating power tools. The direction of bit rotation is reversible and is controlled by running the drill at low speeds for extended ...drill will not run unless the direction of the switch for the purposes listed below: [] Hammer drilling in concrete, brick, or other masonry [] Drilling in wood [] Drilling in ceramics, plastics, fiberglass, and laminates [] Drilling...
Operation Manual - Page 11
... serious personal injury or damage to the chuck.
[] Rotate the chuck counterclockwise to tighten the chuck jaws.
to unplug the tool may result in use. NOTE: Always be thrown from the drill, resulting in the direction of the arrow marked LOCK to tighten the chuck jaws securely on the bit.
Failure to...
Operation Manual - Page 12
... hold the lock-on button, located on the
side of the handle.
[] Release the variable speed switch. [] Release the lock-on the right.
_lb WARNING: The hammer drill has not been designed for type of drilling, slide the drilling mode selector on top of staring threads, the hex nut has been trapped inside the molded...
Operation Manual - Page 13
... bit break- Do not lock the variable speed switch in the opposite direction and could result in accidental starting point. When these situations occur, the drill has a tendency to grab and kick in applications where the drill may need to be suddenly stopped. A WARNING: Before connecting the hammer drill to
a power supply source, always check to...
Operation Manual - Page 14
... hammer mode.
[] Apply light pressure and medium speed for best results in brick.
[] Apply additional pressure for the life of the unit under normal operating conditions. Use of commercial solvents and may be replaced at a very low speed to determine the best speed and pressure. Most plastics are lubricated with plastic parts. Electric tools...
Operation Manual - Page 15
... jaws. [] Insert a hex key into the chuck and tighten the chuck jaws securely. The chuck can now be removed and replaced with a mallet in a clockwise direction. or larger hex key into the chuck of the
drill and tighten the chuck jaws securely. [] Tap the hex key sharply with a new one. [] Unplug the...
Operation Manual - Page 16
... not recommended by your nearest Sears Retail Store for use of this tool are listed above. To avoid the possibility of the Double Insulated System.
A WARNING: Current attachments and accessories available for Service Center information.
16 CRAFTSMAN HAMMER DRILL - Lookfortheseaccessorieast Searsretail: [] HighSpeedBits(Forwoodor metal 1../.2..i.n...M...a..x... [] MasonryBits...
Operation Manual - Page 17
...= May Be Purchased Locally ** Available From Div. 98 = Source 980.0
*** Complete assortment available at your Nearest Sears Retail Store
17 rdAelrwinagys rempaeinrtiopnartsth, e model
|J
SEE BACK...Part No. MODEL NUMBER 315.101370
'_
I Tnhuembmeor deinl anllucmobrreerspwoinlldbeencefoundregoanrdaingplayteouar ttHacAhMeMd ERto thDeRImLoLtoor r hwohuesningo. _"
CRAFTSMAN HAMMER DRILL - Number
...
Operation Manual - Page 18
...Fabrica / SM Marca de Servicio de Sears, Roebuck and Co. For the replacement parts, accessories and owner's manuals that you need to do-it !
and Canada)
www.sears.com
www.sears.ca
Our... de Sears, Roebuck and Co.
® Sears, Roebuck and Co. only) www.sears.com
To purchase a protection agreement (U.S.A.) or maintenance agreement (Canada) on -line for the location of your home-of ...
Similar Questions
Replacement Brushes For 320-26302 Drill?
Are replacement brushes available for craftsman 320-26302 drill? Can't even find a part number.
Are replacement brushes available for craftsman 320-26302 drill? Can't even find a part number.
(Posted by nkjohnso 4 years ago)
Is The Cord For This Drill Available And If So How Do I Order One And The Price?
(Posted by Anonymous-155332 8 years ago)
Craftsman Hammer Drill # 315.115430
When driving long screws, I set the torque setting to max but will not drive the screws into the woo...
When driving long screws, I set the torque setting to max but will not drive the screws into the woo...
(Posted by mjbjwiz 10 years ago)
20v Drill Switch Replacement
good day, how do I replace the switch as it seems to have additional wires as aposed to the 2 in and...
good day, how do I replace the switch as it seems to have additional wires as aposed to the 2 in and...
(Posted by espo65 11 years ago)
I Need To Replace The Switch On My Hammer Drill But The Switch Is No Longer Avai
(Posted by armanddfrankjr 11 years ago)