Canon PIXMA MX712 Support Question
Canon PIXMA MX712 Support Question
Find answers below for this question about Canon PIXMA MX712.Need a Canon PIXMA MX712 manual? We have 8 online manuals for this item!
Question posted by muebuch85234 on February 15th, 2013
Pixma Mx712 Error Code C0000
What does the error code mean and what do I need to do to fix the error.
Current Answers
Answer #1: Posted by tintinb on February 18th, 2013 11:50 PM
tintinb
Member since:
October 26th, 2012 Points: 7,056,560
Member since:
October 26th, 2012 Points: 7,056,560
Based on my research, you can follow these steps to solve the Error Code C000 of your Canon Pixma printer.
- Switch off the printer
- Disconnect the power cable
- Open door
- Remove the orange protective tape (A) and remove the white polystyrene(protective equipment) (B).
- Verify in the printer there is no protective equipment
- Close the door.
- Connect the cable and switch on.
Solution 2 :
- Check for any foreign body in the printer: piece of paper, paper clip...
- Check for any paper jams.
Solution 3:
- This error code C000 could be made by an empty cartridge: check for this.
Source:
http://mpcsidayu.blogspot.com/2011/04/how-to-solve-error-c000-on-canon-pixma.html
If you have more questions, please don't hesitate to ask here at HelpOwl. Experts here are always willing to answer your questions to the best of our knowledge and expertise.
Regards,
Tintin
Related Canon PIXMA MX712 Manual Pages
Guide for Printer Setup for Network - Page 1
...Network Connection
Wireless Connection Preparation for Connection Printer Setup Setup Procedure Selection
Push Button Method Standard setup WPS Other setup (Advanced setup)
Disable WEP WPA/WPA2
Wired Connection Preparation for the printer. Setup Guide
This guide provides information for setting up a network connection for Connection Cable Connection Printer Setup
Character Entry
Troubleshooting
Guide for Printer Setup for Network - Page 2
...Press the MENU button (A) on your personal information to a third party. • This printer cannot be used as your system environment.
For details, refer to the manual of your ...device supports IEEE802.11n, 802.11g or 802.11b. • If your printer to prepare an access point. b Printer Setup
1.
Change the
security protocol for Connection
Before Starting Wireless Connection Setup 1....
Guide for Printer Setup for Network - Page 3
...Advanced setup) → d-D Connecting to the Network by Entering the Access Point's Settings Directly on the printer but you are unsure if your access point or router supports this technology, press the Stop button and ...(blue) Wi-Fi lamp (C) lights up when wireless connection is displayed on the Printer
When using WEP key number WEP key 2 to select the Wireless LAN setup icon.
3. If the...
Guide for Printer Setup for Network - Page 4
... (for or connecting to the access point manual.
2. When the left screen appears, press the OK button. Press and hold the WPS button on the printer flashes while searching for about 5 seconds). Press the OK button on pressing the WPS button, refer to the access point.
3.
d-A Push Button Method d Connection...
Guide for Printer Setup for Network - Page 5
.... Press the OK button.
3. Enter the network password (WEP key or passphrase) of the screens above will be displayed on the printer. 5. Select your access point or router into the printer. 7. Press the OK button.
6. Make sure that the network password is correct. Press the left screen appears, press the OK button...
Guide for Printer Setup for Network - Page 6
.... 4. Press the OK button on the access point (for or connecting to the access point manual.
7. For details on the printer flashes while searching for about 5 seconds). The (blue) Wi-Fi lamp on pressing the WPS button, refer to the access... the OK button.
6. Press the OK button.
5. Press and hold the WPS button on the printer within 2 minutes. d-C WPS d Connection Using WPS
1.
Guide for Printer Setup for Network - Page 10
...;ce use, consult your network administrator. • Take added care when connecting to a network that the printer is not protected with an Ethernet cable (A). If the power is a risk of the mode buttons (A) will need an Ethernet cable (sold separately).
1. Remove the Cap (A) of the upper port located on one of disclosing...
Guide for Printer Setup for Network - Page 11
c Printer Setup
1. Press the MENU button (A) on the printer.
2. Press the OK button.
6. Select LAN settings. 7. Press the OK button.
10.Select Wired LAN active. 11. Select Device settings. 5. Press the OK button (B).
4. Press the OK button.
8. Select Change wireless/wired. 9. Press the OK button. Use the
buttons (A) to select the Setup icon.
3.
Guide for Printer Setup for Network - Page 13
... the keyboard type.
2. Use the
buttons (B) to select a character from the on -screen keyboard.
3. When an on-screen keyboard shown above is displayed on the printer. Character Entry
You can enter the characters when the keyboard is displayed, press the center Function button (A) to switch to a keyboard that supports characters you...
Guide for Printer Setup for Network - Page 14
... below: Turn off , then turn it back on. • Are the access point and printer installed in an open space where wireless communications are found.
Select the MAC address of your access...same name exist. After checking the above points, press the left Function button (A) on the printer to the manual supplied with the access point or contact its manufacturer. For details on how to...
Guide for Printer Setup for Network - Page 16
...OK button. 4.
In addition, when using an access point that the MAC address of the printer will be used as the communication standard. If the problem is not resolved, there may be ...WEP key number 1, or select a WEP key number by entering wireless connection settings of the printer directly. For details on how to change the communication standard to something other causes. If ...
Guide for Printer Setup for Network - Page 17
... Select Device settings, then press the OK button. 4. For details on the access point, change the settings of the printer. 1. Select Setup, then press the OK button. 3. Select LAN settings > Confirm LAN settings > WLAN ... on how to change settings so that the MAC address of the printer will be accepted. Press the MENU button. 2. Use the
buttons (B) to check MAC address.
Guide for Printer Setup for Network - Page 18
... again. See the access point manual. Wait for a while, then configure WPS settings again. The screen appears when an error occurs. For details on only one access point. Connection failed.
WPS
Cannot connect. The screen appears when multiple access...access point, refer to the manual supplied with the access point or contact its manufacturer. Timeout error.
Guide for Printer Setup for Network - Page 19
... the sections below: Turn off , then turn it back on. • Are the access point and printer installed in an open space where wireless communications are found. Do you have only one AccessPoint only, then ...it off the access point, turn it back on, then press the left Function button on the printer to check the MAC address of the access point can be other causes. If the problem is ...
Guide for Printer Setup for Network - Page 20
... point or contact its manufacturer.
For details on the access point, change the settings of the printer will be accepted. However, they can be selected.
The Access Point Name is set... as the communication standard. For details on how to check or change the settings of the printer. 1. Select LAN settings > Confirm LAN settings > WLAN setting list to change the ...
Guide for Printer Setup for Network - Page 21
...64257;ltering is enabled on the access point, change settings so that the MAC address of the printer will be accepted. Make sure that automatically creates WEP keys, check the WEP key (hexadecimal)... created automatically on the access point, then enter it on the printer. See also the sections below to the manual supplied with the access point or contact its ...
Guide for Printer Setup for Network - Page 22
... is inactive, enable the DHCP function or specify the IP address (IPv4 only) of the printer and configure wireless connection settings again. Use the
buttons (B) to select Wireless LAN setup...OK button. 7 Select IPv4, then press the OK button. 8. To specify the IP address of the printer, follow the procedure below. 1. Select Device settings, then press the OK button. 4. Press the MENU ...
MX710 series Specifications - Page 1
...Dialing Automatic dialing
Coded speed dial (max. 100 destinations) Group dial (max. 99 destinations) Regular dialing (with Numeric buttons) Automatic redialing Manual redialing (with the Canon inkjet printer. Print width ... changed
notice. Specifications are a theoretical maximum transmission speed between the printer and an equivalent network device, and do not indicate the actual transmission...
MX710 series Especificaciones [Spanish Version] - Page 1
...lines/mm) Black Extra Fine: 300 X 300 dpi Color: 200 X 200 dpi
Dialing Automatic dialing
Coded speed dial (max. 100 destinations) Group dial (max. 99 destinations) Regular dialing (with Numeric ...Windows Vista or Windows XP pre-installed.
• Windows: Uninstall software bundled with the Canon inkjet printer before upgrading from Mac OS X 10.6 to Mac OS X Lion 10.7, install software bundled with...
Similar Questions
Canon Pixma Ts3522 Error Code: E03
How do I fix the E03 error when the paper isn't jammed and the top is closed? I've tried just about ...
How do I fix the E03 error when the paper isn't jammed and the top is closed? I've tried just about ...
(Posted by itsmatthewdeangelo8676 2 years ago)
Pixma Mx712 Displaying Error Code U052
My MX712 just started displaying error code U052 and is not responding to any corrective action. I h...
My MX712 just started displaying error code U052 and is not responding to any corrective action. I h...
(Posted by phwardjr 8 years ago)
Canon Pixma Mx 710 Series -error Codes
An error occured when printing on my Canon Pixma 710 series. It states on the panel Error Code COOO....
An error occured when printing on my Canon Pixma 710 series. It states on the panel Error Code COOO....
(Posted by mtm3 9 years ago)
Canon Pixma Mx850 - Error Code: B200 What Should I Do?
Canon Pixma MX850 - Error Code: B200 What should I do?
Canon Pixma MX850 - Error Code: B200 What should I do?
(Posted by jndcruise 12 years ago)