Black & Decker GH710 Support Question
Black & Decker GH710 Support Question
Find answers below for this question about Black & Decker GH710.Need a Black & Decker GH710 manual? We have 1 online manual for this item!
Question posted by anglaruba on August 4th, 2023
I Need Parts For A Gh710 Trimmer.the Bearing Housing And The Needle Bearing
The person who posted this question about this Black & Decker product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by SonuKumar on August 4th, 2023 7:41 PM
SonuKumar
Member since:
May 9th, 2021 Points: 16,627,780
Member since:
May 9th, 2021 Points: 16,627,780
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Black & Decker GH710 Manual Pages
Type 1 Manual - GH710 - Page 1
... a question or experience a problem with an agent.
if not, the motor will overheat (page 5).
• When replacing the line, use the cord retention feature (page 7).
1 GH710
TRIMMER / EDGER INSTRUCTION MANUAL
Model Number GH710
Thank you call 1-800-544-6986 from 8 a.m.
Model No.
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
Type 1 Manual - GH710 - Page 2
... Plugs 4 Safety Warnings and Instructions: Extension Cords 4
WARNING: When using electric gardening appliances, basic
safety precautions should be caught in death or serious injury. The....
CAUTION: Indicates a potentially hazardous situation which , if not avoided, will result in moving parts.
Wear heavy long pants to contain long hair. • NYLON LINE - Keep face, ...
Type 1 Manual - GH710 - Page 3
...is damaged should be used for alignment of moving parts, binding of moving the tool or examining the damage. Check for the gardening appliance. Any tool that it from the power...8226; DAMAGE TO CORD - WARNING: When servicing double insulated tools, USE
ONLY IDENTICAL REPLACEMENT PARTS. Replace or repair damaged cords. DO NOT allow any other condition that for any damage ...
Type 1 Manual - GH710 - Page 5
... SUPPLIED): - THE GUARD MUST ALWAYS BE ON THE TOOL TO PROTECT THE USER.
• Turn the trimmer upside B 2
down and slide it "snap" into
place.
• Using a phillips
screwdriver, remove ...NEVER OPERATE TOOL WITHOUT GUARD FIRMLY IN PLACE. Auxillary Handle
5 5. Cord Retainer
3. Motor Housing
7. COMPONENTS
Figure A
A
1. Switch 4
2. Cord Receptacle
4. Make
4
sure the ...
Type 1 Manual - GH710 - Page 6
...
handle on so that your front
arm is straight when the
trimmer is
achieved, tighten the collar
by
loosening the collar (9) and
rotating it opposite of the
trimmer can be
adjusted so that it "snaps" into place (figure F). sides of the upper housing as shown in figure E (with your hand.
ATTACHING THE AUXILIARY...
Type 1 Manual - GH710 - Page 7
... string-like objects which might be trimmed and remove any wire which could become entangled in the trimmer.
Cut with the tip of the tool, such as shown in figure J. Plug the receptacle...end of the extension cord into the slot (10) in the
end of a chain link fence. OPERATING THE TRIMMER
• Maintain a cutting angle of 5° to ANSI Z87.1 (CAN/CSA Z94.3) while operating this ...
Type 1 Manual - GH710 - Page 8
..., out of 24 inches (609.6 mm) between the guard and your feet as shown in the
trimmer position. When using the tool, retract the wire
7
edge guide to the trimming
position by the ... a maintenance edger, turn the collar (9) as shown in part 1 of figure K. • Hold the metal shaft and rotate the lower housing 180° as shown in part 2. • Turn the collar (9) until it clicks
L...
Type 1 Manual - GH710 - Page 9
... guide the
line into the other
(figure N) in the trimmer head (figure M). • Replace spool with Black & Decker model # DF-065. • Grasp empty spool (d) with one of housing
nylon line. mechanism senses when more feeding if the cutting or edging is needed and feeds
• Take the new spool and
and trims...
Type 1 Manual - GH710 - Page 10
Your trimmer line can dull over time. For best
results, factory wound spools are likely to
become tangled ... tool.
• Remove the empty spool from the tool
as described in "REPLACING THE SPOOL".
• First wind new line onto the uppermost part of
the spool.
• Feed 3/4 inch (19mm) of
P
cutting line into one side
of the spool as described in the direction of...
Type 1 Manual - GH710 - Page 11
... the following suggestions:
• Carefully clean the spool and housing. • Remove the spool and check if the lever in the trimmer head. • Ensure that it just reaches the line trimmingblade...line until it protrudes approximately 5-3/8 inches (136mm) from the spool).
Use the edge guide if needed to approximately 3 inches (76.2mm). If it back on the spool cap with the tip ...
Type 1 Manual - GH710 - Page 12
To find your local service location, refer to accessories. Proof of purchase may be required. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you have other rights which vary from whom it was purchased (provided that are parked in holding slots (K) figure P ...
Similar Questions
Lst 300 Started Making A Howling Noise. Where Can I Get Replacement Parts?
My lst300 started making a howling noise. Sounds like a bearing going out. Is there some place that ...
My lst300 started making a howling noise. Sounds like a bearing going out. Is there some place that ...
(Posted by kchoate100 11 months ago)
Do Have A Motor Housing For Black And Decker
Do you have a motor housing for a Black and Decker model no: LSTE252 part no: black and decker model...
Do you have a motor housing for a Black and Decker model no: LSTE252 part no: black and decker model...
(Posted by dlove002 1 year ago)
Is The Bushing/bearing At The Top Of The Motor Shaft, Above The Brushes Availabl
(Posted by jcash1238 3 years ago)
Hedge Trimmer Not Working When Charged Battery Is Inserted.
When I attach a charged battery to my hedge trimmer (NHT524) and try using it, all I hear is a loud ...
When I attach a charged battery to my hedge trimmer (NHT524) and try using it, all I hear is a loud ...
(Posted by solom5 6 years ago)
Need To Drawing Of The Wand For A 12bde-170
Need a drawing< took the handle apart and 2 springs fell out..need to know where the go
Need a drawing< took the handle apart and 2 springs fell out..need to know where the go
(Posted by johnccarlson 9 years ago)