Bissell Powerforce Helix Bagless Upright Vacuum 1700 Support Question
Bissell Powerforce Helix Bagless Upright Vacuum 1700 Support Question
Find answers below for this question about Bissell Powerforce Helix Bagless Upright Vacuum 1700.Need a Bissell Powerforce Helix Bagless Upright Vacuum 1700 manual? We have 2 online manuals for this item!
Question posted by lindseyajones on February 26th, 2017
Serial Number For Powerforce Helix Model 1700
There's a model number, but no serial number on this model.
Current Answers
Answer #1: Posted by Odin on February 27th, 2017 1:25 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
I'm afraid you'll have to elicit guidance from the manufacturer (or possibly from the merchant). For the manufacturer, use the contact information here--https://www.contacthelp.com/bissell/customer-service--or use the corporate contact information here--http://www.corporateofficeowl.com/bissell/Corporate%20Office. gl
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Bissell Powerforce Helix Bagless Upright Vacuum 1700 Manual Pages
Users Guide - Page 2
....)
or use in this appliance has a polarized plug (one way. IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT VACUUM. Always connect to a polarized outlet (one slot is necessary when used as a handle, close a door on a level surface... shock, turn power switch off by cord, use only. SAVE THESE INSTRUCTIONS
This model is plugged in the outlet, reverse the plug.
Users Guide - Page 3
...pages 7-9), and if there is a problem, troubleshooting (page 10). Thanks for buying a BISSELL vacuum! Safety Instructions 2
Warranty 11
Product View 4 Assembly 5
Service 11 Contact Information 11
Operations 6-7...® Tool
(Model 1701 Only)
(Model 1701 Shown)
NOTE: Standard accessories may vary by model.
What's in one of our innovative products with your vacuum works as well ...
Users Guide - Page 4
... 15 Dusting Brush
16 Lower Cord Wrap 17 Hose Wand 18 Power Switch Pedal 19 Handle Recline Pedal 20 Foot Hose 21 Product Rating Label &
Serial Number
Users Guide - Page 5
...put it back to store it down at the bottom of the vacuum and twist to lock it into place.
5
Put your accessory tools on the
vacuum and you're ready to go!
You can be found inside the...the hose clip and connect the hose wand to lock it into place. Assembly
WARNING
Do not plug in your vacuum until you are taped to the handle in a plastic bag.
4 3
Then wrap the power cord around the ...
Users Guide - Page 6
... time. To reduce the risk of the unit.
Operations: Height Adjustment
You can easily raise or lower your vacuum off when you 're finished, lean it is in the upright position when using your vacuum without these filters. Press it into rotating brush.
6
www.BISSELL.com NOTE: Some frieze and berber carpets have...
Users Guide - Page 7
...
Dusting Brush
Extension Wand
Your new PowerForce Helix vacuum not only does a great job on each side and pop into place. www.BISSELL.com 7
Parts & Supplies
For Parts and Supplies, go to www.BISSELL.com and enter your model number in the
Crevice Tool
TurboBrush® Tool
(Model 1701 Only)
upright position, pick the accessory tool that...
Users Guide - Page 8
...WARNING
To reduce the risk of electrical shock, turn power switch off and disconnect polarized plug from vacuum. Maintenance: Emptying the Dirt Container
1
2
Press empty button.
Clean it with mild detergent, rinse... over a trash bin, press release button on the front. WARNING
Do not operate the vacuum with damp or wet filters, without filters in place or with the dirt container missing....
Users Guide - Page 9
... twisting to the left then pull it to lift dirt container away from the foot hose and check for clogs. Model 1700
Model 1701
Maintenance: Replace the Brush & Belt
1
2
3
Unplug vacuum, turn over the motor shaft and the brush roll. Maintenance: Clearing a Clog
1
2
screw
3
Remove the hose from inside of the tank.
air path...
Users Guide - Page 10
... Check/replace fuse or reset breaker
Empty dirt container Check, remove debris or clean
Hose not secure
Dirt container not in place
Vacuum cleaner won't pick up dirt
Vacuum path clogged
Rotating power brush drive belt broken Drive belt stretched
Floor brush bristles worn Floor brush jammed
Check to be obstructing the...
Users Guide - Page 12
... !
Special Promotions
Optional: Register your original sales receipt. Rate this product and let us with any important product maintenance reminders and alerts.
Please record your Model Number
Please record your Purchase Date
NOTE: Please keep your email to www.BISSELL.com and enter your product today!
Faster Service
Supplying your information now...
Similar Questions
I Put A New Belt On My Powerforce Helix Vacuum And The Vacuum Brush Bar Still Wi
(Posted by Anonymous-143512 9 years ago)
How To Change A Bissell Powerforce Helix Vacuum Filter
(Posted by tecCyra 10 years ago)
How To Change All The Filters On A Bissell Powerforce Helix Upright Vacuum
model # 12b1?
model # 12b1?
(Posted by bnyask8er 10 years ago)
Bissell Powerforce Helix Model 68c7
Its pick up but not like it was, has a strange sound when running. I didn't see a belt.
Its pick up but not like it was, has a strange sound when running. I didn't see a belt.
(Posted by rashidahwilliams 10 years ago)
Bissell Powerforce Helix Bagless Upright Vacuum How To Replace Power Cord
(Posted by morray 10 years ago)