Biostar P4M80-M4 Support Question
Biostar P4M80-M4 Support Question
Find answers below for this question about Biostar P4M80-M4.Need a Biostar P4M80-M4 manual? We have 1 online manual for this item!
Question posted by gooddogg on March 22nd, 2015
System Info Says I Have P4m80p-v7. Board Says P4m80-m4 But It Is A 775 Socket.
Is there a manual for this board? The p4m80-m7 isn't quite right either. A different scan product reports it as P4M800CE-8237.
Current Answers
Related Biostar P4M80-M4 Manual Pages
P4M80-M4 user's manual - Page 1
...product names are designed to provide reasonable protection against harmful interference in a particular installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in this user's manual. Further the vendor reserves the right... will not be responsible for any purpose.
P4M80-M4
FCC Information and Copyright
This equipment has been...
P4M80-M4 user's manual - Page 3
...VT8237R. Data transfer rate up to 2GB. (Following table is only for reference.)
DIMM Socket Location
DDR Module
Total Memory Size
DIMM1 DIMM2
128MB/256MB/512MB/1GB *1 128MB/256MB/512MB/...Do not support Williamate CPU. South Bridge: VIA VT8237R.
P4M80-M4
CHAPTER 1: INTRODUCTION
1.1 MOTHERBOARD FEATURES
A. Supports 266/333/400MHz DDR devices.
Supports 2 Serial ATA (SATA) devices. ...
P4M80-M4 user's manual - Page 4
... on-board connectors support 4 devices. On Board AC'97 Sound Codec Chip: REALTEK ALC655. Supports 10/100 Mb/s auto-negotiation operation.
Supports PIO Mode 0~4. Expansion Slots Three 32bit PCI bus master slots.
Supports SPDIF out function. Supports ACPI and PCI power management. One CNR slot.
2 One AGP 4x/8x compatible slot. P4M80-M4
Super...
P4M80-M4 user's manual - Page 5
... In 1/ Bass/Center
3 Back Panel I /O Connectors and Headers 1 front panel header supports front panel facilities. 1 CD-in connector supports 1 CD-ROM audio-in connector. P4M80-M4
Internal On-board I /O Connectors 4 USB 2.0 ports. 1 VGA port. 1 Serial port. 1 Printer port. 1 RJ-45 LAN jack. 1 PS/2 Mouse port. 1 PS/2 Keyboard port. 1 vertical audio port including 1 line...
P4M80-M4 user's manual - Page 6
... BIOS. Supports ACPI Supports USB Function. Software Supports Warpspeeder™, 9th Touch™, WINFLASHER™ and FLASHER™.
1.2 PACKAGE CHECKLIST
FDD Cable X 1 HDD Cable X 1 User's Manual X 1 Fully Setup Driver CD X 1 USB 2.0 Cable X1 (optional) Serial ATA Cable X 2 (optional) SPDIF out Cable X 1 (optional) Rear I/O Panel for ATX Case X 1
4
P4M80-M4 B.
P4M80-M4 user's manual - Page 7
JATXPWR1
P4M80-M4
1.3 LAYOUT AND COMPONENTS
JKBMS1
PU Socket 478
JCOM1
CPU1
JCFAN1
JPRNT JVGA1
DIMM1 DIMM2
JUSB1
JATXPWR2
IDE1 IDE2
JUSBLAN1 JAUDIO
Super I/O
BIOS
P4M800
AGP1
LAN
JAUDIO1 JCDIN1 JAUX1 (optional)
Codec
PCI1
JSPDIFO1
CNR1
PCI2 PCI3
JUSB3 JUSB4
BAT1
VT8237R
JSATA2
JSATA1
FDD1
JSFAN1
JCMOS1 JCI1
JPANEL1
Note: ■ represents the 1st pin.
5
P4M80-M4 user's manual - Page 8
... on the CPU and buckle it.
Connect the CPU FAN power cable to complete the installation. P4M80-M4
CHAPTER 2: HARDWARE INSTALLATION
2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU)
PU
PU
Step 1: Pull the lever sideways away from the socket and then raise the lever up to a 90-degree angle.
This completes the installation.
6 Step 2: Look...
P4M80-M4 user's manual - Page 9
... positive and should be connected to pin#2, and the black wire is Ground and should be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to GND.
7
P4M80-M4
2.2 FAN HEADERS
These fan headers support cooling-fans built in the computer. The fan cable...
P4M80-M4 user's manual - Page 10
Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot.
2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated.
8 DIMM1 DIMM2
P4M80-M4
2.3 INSTALLING SYSTEM MEMORY
PU
1. Unlock a DIMM slot by pressing the retaining clips outward.
P4M80-M4 user's manual - Page 11
... two HDD connectors IDE1 (primary) and IDE2 (secondary).
The first hard drive should always be connected to four hard disk drives. P4M80-M4
2.4 CONNECTORS AND SLOTS
FDD1: Floppy Disk Connector The motherboard provides a standard floppy disk connector that provides PIO Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality. This connector...
P4M80-M4 user's manual - Page 12
This PCI slot is also equipped with an Accelerated Graphics Port (AGP). This motherboard supports video cards for PCI slots, but it is equipped with 3D graphics. P4M80-M4 PCI1~PCI3: Peripheral Component Interconnect Slots This motherboard is a bus standard for expansion cards.
PU
10 An AGP card will attach directly to that video card...
P4M80-M4 user's manual - Page 13
PU
11 P4M80-M4 CNR1: Communication Network Riser Slot The CNR specification is an open Industry Standard Architecture, and it defines a hardware scalable riser card interface, which supports modem only.
P4M80-M4 user's manual - Page 14
When the jumper cap is "open". P4M80-M4
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1 HOW TO SETUP JUMPERS
The illustration shows how to connect 20-pin power connector on pins, the jumper is "close", if ...
P4M80-M4 user's manual - Page 15
...
Left
1
13
11 Right line in/Rear
speaker Right
12 Right line in/Rear
speaker Right
13 Left line in/Rear
speaker Left
14 Left line in/Rear
speaker Left
13
PU
Pin
Assignment
1
+12V
3
4
2
+12V
1
2
3
Ground
4
Ground
JAUDIO1: Front Panel Audio Header
This header allows user to CPU power circuit. P4M80-M4
JATXPWR2: ATX Power...
P4M80-M4 user's manual - Page 16
It allows user to connect the PCI bracket SPDIF output header. P4M80-M4
JSPDIFO1: Digital Audio-out Connector
This connector allows user to connect the PC case's front panel switch functions. PU
PWR_LED
SLP
On/Off IR
++ -
2
24
1
+-
...
P4M80-M4 user's manual - Page 17
...; Clear CMOS Procedures:
1.
Remove AC power line. 2. Wait for five seconds. 4. Set the jumper to "Pin 2-3 close ". 5. P4M80-M4
JUSB3/JUSB4: Front USB Headers
This motherboard provides 2 USB 2.0 headers, which allows user to avoid damaging the motherboard. PU
Pin Assignment
1 +5V (fused)
2 +5V (fused)
3 USB-
4 USB-
2
10 JUSB3 5 USB+
6 USB+
7 Ground
1
9 JUSB4 8 Ground
9 Key...
P4M80-M4 user's manual - Page 18
P4M80-M4
JSATA1/JSATA2: Serial ATA Connectors
The motherboard has a PCI to connect the audio source from the variety devices, like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc..... with 2 channels SATA interface, it satisfies the SATA 1.0 spec and with transfer rate of 1.5Gb/s.
PU
Pin Assignment
1
Left channel input
2
Ground
3
Ground
4
Right channel input
4
1
16
P4M80-M4 user's manual - Page 19
If the signal has been triggered, it will record to monitor PC case open signal
2
Ground
12
17 P4M80-M4
JCI1: Chassis Open Header
This connector allows system to the CMOS and show the message on next boot-up. PU
Pin Assignment
1
Case open status.
P4M80-M4 user's manual - Page 22
...plugged in ;
Set master/slave jumpers correctly.
2. No power to disk controller board. Replace cable.
Make sure correct information is extremely important. Cannot boot system after ... other drives.
20
Using even pressure on .
Screen message says "Invalid Configuration" or "CMOS Failure." P4M80-M4
4.3 TROUBLESHOOTING
Probable
Solution
1. Check cable running from disk to...
P4M80-M4 user's manual - Page 31
P4M80-M4 Note: Because the overclock, overvoltage, and hardware monitor features are controlled by several separate chipset, [WarpSpeeder™] divide these features to separate panels. If one chipset is not on board, the correlative button in Main panel will be disabled, but will not interfere other panels' functions. This property can make [WarpSpeeder™] utility more robust.
29
Similar Questions
Biostar P4m80-m7 Wattage?
What is the wattage of this mother board. I want to acquire a replacement supply for it.
What is the wattage of this mother board. I want to acquire a replacement supply for it.
(Posted by jlm14588 9 years ago)
My Bios Version Is 1.05 The Model Is P4m80-m4 And The Chipset Is P4m800ce-8237
(Posted by Anonymous-82738 11 years ago)
I Baught A New Hard Disk 1.0tb
hi, I baught a new hard disk 1.0TB I need to know if it'll work with my Biostar P4M80-M4 ver: 7.0...
hi, I baught a new hard disk 1.0TB I need to know if it'll work with my Biostar P4M80-M4 ver: 7.0...
(Posted by ashraf900 11 years ago)
Tengo La Board P4m80-m4 Y No Da Sonido Y Ya He Descargado Varios Realtek Y Nada.
(Posted by arcangrljav 11 years ago)