Behringer NX4-6000 Support Question
Behringer NX4-6000 Support Question
Find answers below for this question about Behringer NX4-6000.Need a Behringer NX4-6000 manual? We have 2 online manuals for this item!
Question posted by Ike35517 on September 13th, 2023
Nx4-6000 Has 5 Rapid Flashing Lights
when turned on, 5 lights flash rapidly.
Current Answers
Answer #1: Posted by SonuKumar on September 13th, 2023 9:48 PM
SonuKumar
Member since:
May 9th, 2021 Points: 16,609,800
Member since:
May 9th, 2021 Points: 16,609,800
The 5 lights flashing rapidly on your Behringer NX4-6000 mixer is an indication of a problem with the unit. The specific problem may vary depending on which lights are flashing, but it is likely that there is a problem with the power supply, the audio input, or the audio output.
Here are some possible causes of the 5 lights flashing rapidly on your Behringer NX4-6000 mixer:
The power supply is not working properly.
The audio input is not connected properly.
The audio output is not connected properly.
There is a problem with the mixer's internal circuitry.
If you are not sure what is causing the problem, it is best to consult the Behringer NX4-6000 manual or contact Behringer customer support for assistance.
Here are some troubleshooting steps you can try:
Check the power supply connections. Make sure that the power cord is plugged into the mixer and into a power outlet that is working properly.
Check the audio input connections. Make sure that the audio cables are properly connected to the mixer and to the audio source.
Check the audio output connections. Make sure that the audio cables are properly connected to the mixer and to the audio destination.
Reset the mixer. Press and hold the RESET button for 5 seconds.
If the problem persists, contact Behringer customer support.
I hope this helps!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Behringer NX4-6000 Manual Pages
Product Information Document - Page 1
... an ultra-efficient, switch-mode power supply ensure this feather-light powerhouse will drive your rig effortlessly for ultimate reliability
## Independent DC, LF and thermal
overload protection on each channel automatically protects amplifier and speakers without shutting down the show
The NX4-6000 power amplifier packs 6000 Watts (4 x 1600 Watts @ 2 Ohms; 2 x 3000 Watts @ 4 Ohms) into 4 Ohms...
Product Information Document - Page 2
... Amplifiers
NX4-6000
Ultra-Lightweight 6000-Watt 4-Channel Class-D Power Amplifier ...music-group.com.
2 of dual mono, stereo or mono bridge modes. Just as elegant as Limit LEDs to indicate when the amplifier is channeled to our High-Density Class-D amplifier...NX4-6000's built-in Germany
Class-D - The rear panel is ready for action. After pressing the Power button, the Power LED lights...
Product Information Document - Page 3
... MUSIC Tribe factory using state-of 5 the BEHRINGER NX4-6000 power amplifier is rendered perfectly ruler flat via impedance compensation. Experience the BEHRINGER NX4-6000 amplifier at your most sophisticated test equipment available in the world. Sound Value
Sporting massive output ratings, lightweight Class-D technology and an equally lightweight price tag -
Our products are turning...
Product Information Document - Page 5
... owners. All trademarks are subject to change without notice. Product Information Document
Portable Amplifiers
NX4-6000
Ultra-Lightweight 6000-Watt 4-Channel Class-D Power Amplifier with SmartSense Loudspeaker Impedance Compensation
For service, support or more information contact the BEHRINGER location nearest you:
Europe
MUSIC Tribe Brands UK Ltd. Tel: +44156 273 2290 Email: CARECrea...
Quick Start Guide - Page 6
...clockwise.
(6) POWER button turns the amplifier on and off and the amp will behave normally.
(4) POWER LED lights up to indicate the...operation, simply depress the BREAKER and power up continuously. The SIGNAL LEDs light to the target volume 10 NX6000/NX3000/NX1000/NX4-6000/NX6000D/NX3000D/NX1000D
NX6000/NX3000/NX1000/NX4-6000 Controls
(1)
(2)
(3)
(4) (6)
(2)
(5) (13)
(7)
NX3000/NX1000...
Quick Start Guide - Page 9
...rotated).
(11) POWER button turns the amplifier on ). The BREAKER acts in each channel. The SIGNAL LEDs light to prevent overheating.
(3) ... depress the BREAKER and power up continuously. Reduce the input gain if the red LIMIT LED lights up the unit again. 16 NX6000/NX3000/NX1000/NX4-6000/NX6000D/NX3000D/NX1000D
NX6000D/NX3000D/NX1000D Controls
(1)
(2)
(4) (6) (8) (9)
(2)
(3) (5) (7)...
Quick Start Guide - Page 20
...attack limiter (peak)
20 total presets, 19 user-definable
Quick Start Guide 39
NX6000D
NX6000
NX4-6000
NX3000D
System
Inputs
2 x combo jacks
4 x combo jacks
2 x combo jacks
Input impedance...style professional speaker connectors
Output circuit type
Class D
Distortion 38 NX6000/NX3000/NX1000/NX4-6000/NX6000D/NX3000D/NX1000D
Specifications
Maximum Output Power Stereo / 4-channel 2 Ω...
Quick Start Guide - Page 21
...300 ms
-
-
3 filter types, up to -front air flow
Amplifier protection
Thermal and DC protection Stable into 4 Ω
Digital Signal Processing... x locking-style professional speaker connectors
Output circuit type
Class D
Distortion
100 dB
USB
-
40 NX6000/NX3000/NX1000/NX4-6000/NX6000D/NX3000D/NX1000D
Maximum Output Power Stereo / 4-channel 2 Ω per channel, stereo 4 Ω per...
Similar Questions
Can't Select Effects.
I turn the knob to select and then push and nothing happens
I turn the knob to select and then push and nothing happens
(Posted by Breavill96 3 years ago)
Power Button Flashes
The power button on the front flashes when I turn on the power main switch on the back. When I power...
The power button on the front flashes when I turn on the power main switch on the back. When I power...
(Posted by jdcarguy 6 years ago)
How To Reduce The Fan Noise Of Behringer I Nuke 6000 Dsp Amp
sir i want to purchase the behringer i nuke 6000 dsp amp but i am little confused over the fan noise...
sir i want to purchase the behringer i nuke 6000 dsp amp but i am little confused over the fan noise...
(Posted by pwarude54 8 years ago)
El Nu 6000 Prende En 30-60 Se Apaga Los Fan Y Se Qd Queda Mudo. Cual Es El Prob.
(Posted by wtomassini 10 years ago)
Inuke Cut Out, Reset, Now No Lights And Only Stays On 5 Seconds, Why ?
(Posted by garytomlin1972 10 years ago)