Alpine MC20 Support Question
Alpine MC20 Support Question
Find answers below for this question about Alpine MC20.Need a Alpine MC20 manual? We have 1 online manual for this item!
Question posted by elkinsconstruc on July 16th, 2011
I Installed A Cda-9886m With A Mc20 .
the mc20 shows what station is playing ,but i can not control anything . whats wrong?
Current Answers
Related Alpine MC20 Manual Pages
Operating Instructions - Page 1
... 280)
98, Rue de la Belle Etoile, Z.I. Colombo 8, 20090 Trezzano
Sui Naviglio (MI), Italy Phone 02-484781
ALPINE ELECTRONICS DE ESPANA, S.A. Marine Remote Commander System
MC20
• Operating Instructions Please read before using this equipment. ALPINE ELECTRONICS MARKETING, INC. 1-1-8 Nishi Gotanda Shinagawa-ku
Tokyo 141-0031, Japan Phone 03-5496-8231...
Operating Instructions - Page 2
... sure the temperature inside boat is subject to heed them can result in a safe location before turning your Alpine dealer or the nearest Alpine Service Station for periodic cleaning of the boat and cause an accident. Return it to a complete stop the boat in serious injury or death. Failure to repair...
Operating Instructions - Page 3
... ce=,.J To 10P Sub Display Connector - . . . Transceiver Unit
To Steering Wheel Jack
-... Return/Escape
Installation'
MC20 Display Unit
t_ 2.4GHz
Wireless v~
~, Wireless
opti;;;;~i·RUE~M·1·RF·····
. Track Down 5. Search/Enter
7
7. Level/Control Mode 9.
GND +12V
BLACK: connect to Ground (GND)
RED: connect to 12V(+):
··...
Operating Instructions - Page 4
... BL DISPLAY
Turns LCD backlighting ON or OFF
6. Program Menu
Enter Program Mode •
MC20 Display unit
Program Menu Options
1. 10 NUMBER
This is the serial number of the display ...: Bold indicates default menu selection for pairing or re-pairing any MC2 or MC20 display units with any existing MC20 system. CONTRAST
Sets brightness or dimness of serial numbers: 00001 to DEGREES ...
Operating Instructions - Page 5
Press VOL + or VOL until CONTRAST shows on top line of display
5. Press ENT to program new CONTRAST value
6. Enter Program Mode
4. Press ENT to save new CONTRAST value
3. Press VOL + or VOL to exit Program Mode
5 Press ESC to adjust the current CONTRAST value
2. Program Mode Example
1.
Operating Instructions - Page 6
...ENT to exit Program Menu 10. Turn off the existing MC20 system, then turn on and automatically go to pair with ADD MC2 showing on the display, MC2 location may be out of MC2... (see Installation) 3. PRESS ENTER will appear on the display below ADD MC2 on commander is ready to the pairing
screen in the program menu with MC20 system *
6. Connect power and ground wires of MC20 system range...
Operating Instructions - Page 7
Example Systems
...:
Transceiver
~ 2.4GHz Wireless
APN Marine Head Unit
. MC20 Marine Commander System
Transceiver
2AGHz
Wireie~s
~ 2AGHz
·i MC2
Wireless
Add on :
· APN Marine Head Unit
MC20 Marine Commander System with MC2 Add on Commander
7
Operating Instructions - Page 8
...Control
Volume Control 1. ZONE 2
Mute Control 1. Press and hold the VOLUME ZONE button to select the mute zone(s)
MUTE ALL
MUTE ZONE 1
MUTE ZONE 2
2. Follow the remaining steps of new MC20 ...
display will show ADD MC2 like adding an MC2 Commander) follow the instructions below:
1. MC20 Display Unit Re-Pairing Procedure
* To pair an MC20 display unit with a different MC20 system than ...
Similar Questions
Problem With Audio For Cds And Iphone.
The audio for the tuner works great. However, when I switch to disk it will display the song that is...
The audio for the tuner works great. However, when I switch to disk it will display the song that is...
(Posted by aggiefootball4 10 years ago)
Alpine Cda-9886m Poor Radio Reception
I had this professinoally installed and the radio reception is horrible. It is replacing a Kenwood f...
I had this professinoally installed and the radio reception is horrible. It is replacing a Kenwood f...
(Posted by sdafoe 12 years ago)