Actiontec MWTV2TX Support Question
Actiontec MWTV2TX Support Question
Find answers below for this question about Actiontec MWTV2TX.Need a Actiontec MWTV2TX manual? We have 3 online manuals for this item!
Question posted by byersmarcusb on November 30th, 2016
Transmitter Stopped Working
I have the transmitter hooked up to the TV in the living room and the cable box in a bedroom closet. It was working properly one minute and nothing the next. Unplugged the unit and rebooted it, checked the sensors and everything is in place. It has a green blinking link light, replace the remote batteries and no luck. Thanks for your help!
Current Answers
Answer #1: Posted by BusterDoogen on November 30th, 2016 10:19 AM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,397
Member since:
October 30th, 2011 Points: 28,565,397
The LINK LED is used to display the state of pairing between the Transmitter and Receiver. If it is blinking or off, the Transmitter is not paired with any Receiver. If it is glowing steadily, it has paired with a Receiver. Start on page 4 for further troubleshooting tips.
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Actiontec MWTV2TX Manual Pages
Datasheet - Page 1
... patio for a party. Connect another HDTV in the kid's room without needing another set top box without having to , without investing in the bedroom without having to 100 feet away, even working through walls and floors1. This easy-to-use an ugly HDMI cable. Multi-Room Wireless HD Video Kit
Generation 2
Catalog# MWTV2KIT01
Enjoy Brilliant HD...
Datasheet - Page 2
... hard to reach spots • Works up to wirelessly transmit HDTV is included in the box.
And that's it 's as easy as Blu-ray and DRM. And the wireless kit works up in minutes. Multi-Room Wireless HD Video Kit
Generation 2
Works with most devices
MyWirelessTV 2 works with a compact, low profile transmitter and receiver. Everything you 'll be...
Datasheet - Page 3
...the U.S. Transmitter: 1 x HDMI input & 1 x HDMI pass-through 5.1 surround3
• A/V interface
- Supports up to 100' range apart ideally in home environment through when Receiver is turned off. © 2014 Actiontec Electronics, Inc. Multi-Room Wireless HD Video Kit
Generation 2
.Technical Specifications
Devices Supported
• Most HD cable and satellite set-top boxes with HDMI...
Installation Guide - Page 1
... receiver box(s).
Both units come pre-paired to work with each other end of the
HDMI cable into the HDMI port labels Out-to-TV on the back of the
power supply into an HDMI port on the HDTV.
3 Step c Plug the other . Video from
MyWirelessTV 2 Kit.
Therefore, you wish to transmit signal to the Transmitter...
Installation Guide - Page 2
... than on top of the source device's IR Sensor window. A Make sure the IR Blaster cable is slow to respond to the Menu screen. rectly on Transmitter's TV. You can receive IR signal from Receiver to control the Source Device. Multi-Room Wireless HD Video Kit
MyWirelessTV 2
Model# MWTV2TX & MWTV2RX
Quick Start Guide
This Quick Start...
User Manual - Page 2
...Typical MyWirelessTV Connection Configuration 5 2.1.1. Receiver...6 2.2. Connecting the IR Blaster Cable 7 2.4.2. Language ...9 3.1.2. Exit...12 3.1.5. Features ...1 1.2. Resetting to Defaults...13 3.3. Specifications ...17 Package Contents ...2 1.4. Transmitter...5 2.1.2. Connecting the MyWirelessTV Receiver 7 2.4. Video Mode...10 3.1.3. Configuring MyWirelessTV...
User Manual - Page 3
...room, while the gaming console resides in home environment through most walls and floors* Software support - Features
Full 1080p HD output - This user manual will allow you for local TV Compatible with most HDMI-enabled Cable... video in 1080p 60Hz Wirelessly sends live HD audio and video from a set top box, gaming console, or other source with most Blu...
User Manual - Page 4
...in the package are listed below: (1) Wireless HD Video Transmitter (1) Wireless HD Video Receiver (2) Power Adapter (2) High-speed HDMI 1.4 Cable (1) IR Blaster Cable (for Transmitter) (1) IR Receiver Extension Cable (for Receiver) (1) Velcro mounting pad kit (for connecting to TV, IR Transmit, USB, and OTG), one button (SELECT), and...
User Manual - Page 5
... USB Backchannel feature. Reserved for more details. OTG port. The HDMI Out to TV port (a pass-through port) is used to this port is used , via an HDMI cable, to connect the Transmitter to an HDMI source (set top box, Blu-ray player, gaming console, etc.).
HDMI Out to access the GUI...
User Manual - Page 6
...to the transmitter or when the receiver has not paired with the IR Blaster cable connected to the Transmitter).
Note: The use of the IR Receiver Extension Cable is used to connect the IR Receiver cable, used... display, such as a high-definition TV.
IR Ext Port. The HDMI Out to TV port is used , via an HDMI cable, to connect the Receiver to TV Port. And you can access the GUI...
User Manual - Page 7
... shown below:
Note: Connecting a TV to the HDMI Out to a high-definition television monitor. Connecting MyWirelessTV 2
Connecting MyWirelessTV consists of two parts: connecting the Transmitter to a source of the source device in the location you are watching (or playing) your content.
2.1. This chapter will take you through both procedures, as ...
User Manual - Page 8
... up the MyWirelessTV transmitter: 1. Otherwise, get an HDMI cable from your source device.
6 Turn on the source device. Receiver
A typical connection for the Receiver is shown below to the TV, and power off that the POWER LED is previously connected to an HDTV, unplug the HDMI cable from the MyWirelessTV kit box and plug the connector...
User Manual - Page 9
... they're connected. 7. The IR Blaster head comes with a hook-and-loop fastener. Thus, you want to . 2.3. Connecting the IR Blaster Cable
The IR Blaster cable receives the source device remote control signal from the Receiver and delivers it allows the Receiver to the Transmitter. Locate the Infrared (IR) sensor on the Receiver is optional.
User Manual - Page 11
... Language icon is highlighted, which allows you have selected the Language
option. The Main Menu appears as shown below to the Transmitter or when the Receiver has not paired with any Transmitter. To exit the Main Menu, press the MENU button to toggle to display languages.
9 Press the Select button to the...
User Manual - Page 13
... below to start the pairing process. The TV screen will display the Pair to re-pair the devices after you have reset the receiver. However, you need to Transmitter screen and a 120-second countdown.
11... pressing the MENU button, and then press the SELECT
button to pair the receiver with the transmitter: 1. To return to the Main Menu screen, press the MENU button to toggle to confirm...
User Manual - Page 14
... you do not press the Select button on the screen to troubleshoot the problem. Follow the instruction on the transmitter during the 120-second countdown, or pairing fails due to the Main Menu screen, and try pairing again.
...period, press the Select button on the receiver to return to other reasons, the Cannot Detect Transmitter screen will be displayed. You can press the MENU button on your...
User Manual - Page 15
It indicates the connected transmitter or the disconnected state. Signal strength.
Check the current firmware version number on the Main Menu Screen (pressing the.../mwtv2.
13 It indicates the strength of the Main Menu screen. Model name. The receiver reboots automatically to factory defaults, press and hold the MENU button on your MyWirelessTV devices: 1. If the version...
User Manual - Page 16
...turn off, then on) on the front of the Receiver; On a Transmitter, power off the device or remove the USB flash drive during the firmware upgrade process.
14 2. The device reboots.
Once the firmware is complete when the LINK LED flashes in the following sequence:
POWER... off the device, and plug the USB flash drive into the USB port on the front of the Transmitter.
4.
User Manual - Page 17
... IR command twice, connect your PC or laptop. Check the cable connections from the external source (i.e., cable/satellite set top box, Blu-ray player) to the Transmitter and from your IR Extender cable to those problems. Also included are connected properly? Make sure the IR Blaster sensor is selected from the Transmitter out to the external source device's IR...
User Manual - Page 19
Content Protection: HDCP 2.x for HDMI
Power: Input: 5V/2A Consumption:~5W
LED Indicators: Transmitter: Link, Power Receiver: Link, Power, Mode
Mechanical: Weight (per unit): 0.30 lb. (136 g) Dimensions (W x D x H) (per unit): 4.13 x 4.72 x 1.18 in one Tx to one Rx setup
Audio: Non-compressed LPCM Pass-through...
Similar Questions
My Modem Just Shut Off
We were setting up my action tech modem ...it was plugged in and working and then we heard a little ...
We were setting up my action tech modem ...it was plugged in and working and then we heard a little ...
(Posted by Shirlock1227 3 years ago)
Sreenbeam
My Sreenbeam doesn't work in window 10. Is there any update or driver for window 10????
My Sreenbeam doesn't work in window 10. Is there any update or driver for window 10????
(Posted by edisonridderstap 3 years ago)
Need Help Setting Up A Moca Network For Tivos. I Have Actiontec Network Adapter
. Do you have a diagram from the co ax cable from the wall to ?splitter or to MoCA adapter, then to ...
. Do you have a diagram from the co ax cable from the wall to ?splitter or to MoCA adapter, then to ...
(Posted by holtsandra 8 years ago)
Where Can I Find Actiontec Network Extender Warranty Information?
After a few months, my Actiontec Network Extender stopped working on me. I think it is still under w...
After a few months, my Actiontec Network Extender stopped working on me. I think it is still under w...
(Posted by Anonymous-145420 12 years ago)