Yamaha YST SW215 - Subwoofer - 120 Watt Support and Manuals
Get Help and Manuals for this Yamaha item
View All Support Options Below
Free Yamaha YST SW215 manuals!
Problems with Yamaha YST SW215?
Ask a Question
Free Yamaha YST SW215 manuals!
Problems with Yamaha YST SW215?
Ask a Question
Most Recent Yamaha YST SW215 Questions
My Yst Sw215 Powers Up, But Does Not Make Any Sound. Any Ideas?
(Posted by jdaentl 12 years ago)
Popular Yamaha YST SW215 Manual Pages
MCXSP10 Manual - Page 2
... Unplug this Owner's Manual in a safe place for replacement of the obsolete outlet.
10 Protect the power cord from ...
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all servicing to qualified service personnel. Servicing is required when ...instructions.
8 Do not install near water.
6 Clean only with dry cloth.
7 Do not block any heat sources such as power...
MCXSP10 Manual - Page 3
.... Failure to follow instructions could void your authority, granted by Yamaha may cause interference harmful to coaxial type cable.
In the case of assurance that interference will not result in harmful interference with the requirements listed in the users manual, may void your FCC authorization to use the product.
2 IMPORTANT : When connecting this product in...
MCXSP10 Manual - Page 4
... chemical solvents as that the unit is faulty.
• Secure placement or installation is the owner's responsibility. When moving the unit, first disconnect the power plug and the wires connected to use this unit for a long period (ie., vacation, etc.), disconnect the AC power plug from the wall outlet. • To prevent lightning damage, disconnect...
MCXSP10 Manual - Page 5
... AND THEIR FUNCTIONS 13
AUTOMATIC POWER-SWITCHING FUNCTION 15
ADJUSTING THE SUBWOOFER BEFORE USE 16
Frequency characteristics 17
ADVANCED YAMAHA ACTIVE SERVO TECHNOLOGY 18
TROUBLESHOOTING 19
SPECIAL INSTRUCTIONS FOR U.K. SUPPLIED ACCESSORIES 3
PLACEMENT 4
CONNECTIONS 5 1 Connecting to line output (pin jack) terminals of the amplifier 5 2 Connecting to speaker output terminals of the...
MCXSP10 Manual - Page 6
... your existing audio system by connecting to either the speaker terminals or the line output (pin jack) terminals of the amplifier.
• For the effective use of the subwoofer, the subwoofer's super-bass sound should be matched to the sounds of pressing the STANDBY/ON button to turn the power on Advanced Yamaha Active Servo Technology.) This super...
MCXSP10 Manual - Page 8
... will not produce sound.
5 When you connect the subwoofer to the "R" side of the SPLIT SUBWOOFER terminals.
Also, refer to the
owner's manual of your amplifier has no line output (pin jack)
terminal
Caution: Unplug the subwoofer and other speakers should not be correct, that is to say L (left) to L, R (right) to R, "+" to "+" and "-" to the PRE OUT...
MCXSP10 Manual - Page 11
.... If your amplifier has two sets of main speaker output terminals and both terminals can output sound signals simultaneously. • Connect one subwoofer (with speaker cables)
Right main speaker
Subwoofer
Left main speaker
To AC outlet
Speaker output terminals
Amplifier
Right main speaker
Subwoofer
To AC outlet
Speaker output terminals
Left main speaker Amplifier
8
Note
• If...
MCXSP10 Manual - Page 14
CONNECTIONS
■ Using two subwoofers (with speaker cables)
Right main speaker
Left main speaker
Subwoofer
Speaker output terminals
To AC outlet
Right main speaker
Amplifier
Subwoofer To AC outlet
Left main speaker
Subwoofer
Speaker output terminals
To AC outlet
Amplifier
Subwoofer
To AC outlet
11
MCXSP10 Manual - Page 15
...each speaker cable by twisting the coating off. Red: positive (+)
Black: negative (-)
CONNECTIONS
U.S.A., Canada and Australia models only Banana Plug conection are completed, plug in the figure. 2 Insert the bare wire. 3 Tighten the knob. 4 Test the firmness of the connection by pulling lightly
on the cable at the terminal.
Red: positive (+)
Black: negative (-)
Plug in the subwoofer...
MCXSP10 Manual - Page 17
... frequency selected by monitoring the sound.
14 Signals from the INPUT1 terminals are all cut off the subwoofer's power supply from the amplifier. (Refer to "CONNECTIONS" for connecting to change the setting of power in to the OFF position. Goes off when the subwoofer is set to the HIGH or LOW position, the subwoofer's automatic power-switching function operates as described...
MCXSP10 Manual - Page 18
... and to the standby mode manually. This function detects the low-frequency components below 200 Hz of the input signals (i.e., the explosion in red.)
When you play a source again, the power of the subwoofer is on (by pressing the STANDBY/ON button).
15 But please be aware that occurs, set the switch to the...
MCXSP10 Manual - Page 19
... minimum reproducible
frequency can be obtained. If the desired response cannot be looked up in the speakers' catalog or owner's manual.
6 Increase the volume gradually to adjust the volume
balance between the subwoofer and the main speakers. Normally, set to the ON
position, then press the STANDBY/ON button to turn on page 17.
16 Normally...
MCXSP10 Manual - Page 20
... cm or 13 cm) acoustic suspension, 2 way system main speakers
PHASE : Set to the REV(reverse) position
dB
90
80 YST-SW315
70
60 Main speaker
50
40 20
50
100 200
500Hz
PHASE : Set to the REV(reverse) position
dB
90
80
YST-SW215
70
60
Main
speaker
50
40 20
50
100 200
500Hz
■ EX...
MCXSP10 Manual - Page 22
..., disconnect the power cord and contact your authorized YAMAHA dealer or service center. Connect them correctly, that is not listed below or if the instructions given below when this unit does not function properly.
Set the POWER switch to the "HIGH" position. Set the AUTO STANDBY switch to the ON position. Otherwise, set to the OFF position. Speaker cables are...
MCXSP10 Manual - Page 23
SPECIFICATIONS
Type ........ Advanced Yamaha Active Servo Technology
Driver .....25 cm (10") cone woofer (JA2564) Magnetic shielding type .......20 cm (8") cone woofer (JA2165) Magnetic shielding type
Amplifier Output (100 Hz, 5 ohms, 10% THD)
Yamaha YST SW215 Reviews
We have not received any reviews for Yamaha yet.