Use and Care Guide
Page 5
...9632; A water heater set to deliver 120°F (49°C) water to the washer. 39" min. (99.0 cm) ■ A grounded electrical outlet located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa). ■ If you...will need for steamer replacement or repair. ■ A level floor with a total weight (water and load) of the washer. Location Requirements Selecting the proper location for your responsibility. Your washer can cause damage in low temperatures. 24 in temperatures below 32°F (0°C). See "Drain System."...
...9632; A water heater set to deliver 120°F (49°C) water to the washer. 39" min. (99.0 cm) ■ A grounded electrical outlet located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa). ■ If you...will need for steamer replacement or repair. ■ A level floor with a total weight (water and load) of the washer. Location Requirements Selecting the proper location for your responsibility. Your washer can cause damage in low temperatures. 24 in temperatures below 32°F (0°C). See "Drain System."...
Use and Care Guide
Page 8
...the Hot (left) inlet valve. Screw on coupling by hand until it easier to the coupling can result. 8 NOTE: Do not overtighten. Damage to tighten connection with the red color indicator to the coupling can result in the couplings. IMPORTANT: Position the washer so that support the suspension... 6. These bolts also retain the power cord inside the washer until it must be transported at a later date, call your washer, it is seated on the washer. 4. Coupling B. Once the bolt is to the Cold (right) water inlet valve. Using pliers, check the tightness of the hole and completely...
...the Hot (left) inlet valve. Screw on coupling by hand until it easier to the coupling can result. 8 NOTE: Do not overtighten. Damage to tighten connection with the red color indicator to the coupling can result in the couplings. IMPORTANT: Position the washer so that support the suspension... 6. These bolts also retain the power cord inside the washer until it must be transported at a later date, call your washer, it is seated on the washer. 4. Coupling B. Once the bolt is to the Cold (right) water inlet valve. Using pliers, check the tightness of the hole and completely...
Use and Care Guide
Page 11
...interior free of dirt and other garments may be added to a load. Clean Washer Cycle with Steam This washer has a built-in the dispensers when the wash cycle is needed. Auto Water Level This washer automatically adjusts water level for High Efficiency "HE" detergent, fabric...-Efficiency Wash System Your new front-loading, high-efficiency washer saves time with Anti-Escape Valve This washer has a specially designed valve that no agitator, you to return to the washer during the spin cycle. This washer offers up to traditional top-load washers. The 6-Point Suspension System ...
...interior free of dirt and other garments may be added to a load. Clean Washer Cycle with Steam This washer has a built-in the dispensers when the wash cycle is needed. Auto Water Level This washer automatically adjusts water level for High Efficiency "HE" detergent, fabric...-Efficiency Wash System Your new front-loading, high-efficiency washer saves time with Anti-Escape Valve This washer has a specially designed valve that no agitator, you to return to the washer during the spin cycle. This washer offers up to traditional top-load washers. The 6-Point Suspension System ...
Use and Care Guide
Page 23
... Asked Questions) to inform you that Suds Routine was activated. www.whirlpool.com/help In Canada www.whirlpool.ca Washer displaying code message and tone sounds "F20" (Water Inlet Problem-no.... If the problem remains, call for service. Use only HE (High Efficiency) detergents. "F22" (Front door lock) Select PAUSE/CANCEL twice to cancel the cycle. Check the following : Is the power cord...use an extension cord. Are the water inlet valve screens clogged? Washer stops Check the following : Is the washer door firmly shut? Are you washing a large load? Re-select cycle and press START. Was...
... Asked Questions) to inform you that Suds Routine was activated. www.whirlpool.com/help In Canada www.whirlpool.ca Washer displaying code message and tone sounds "F20" (Water Inlet Problem-no.... If the problem remains, call for service. Use only HE (High Efficiency) detergents. "F22" (Front door lock) Select PAUSE/CANCEL twice to cancel the cycle. Check the following : Is the power cord...use an extension cord. Are the water inlet valve screens clogged? Washer stops Check the following : Is the washer door firmly shut? Are you washing a large load? Re-select cycle and press START. Was...