Installation Instructions
Page 19
... questions, contact the manufacturer. • Before servicing or cleaning unit, switch power off at 0.1 static pressure: without applying static pressure, CFM would be hard wired direct with 2-wire with aluminum tape. Check Framing Roof cap 7" round duct Roof cap 10" round duct Exterior blower 10" round duct 300 or 600 CFM...
... questions, contact the manufacturer. • Before servicing or cleaning unit, switch power off at 0.1 static pressure: without applying static pressure, CFM would be hard wired direct with 2-wire with aluminum tape. Check Framing Roof cap 7" round duct Roof cap 10" round duct Exterior blower 10" round duct 300 or 600 CFM...
Installation Instructions
Page 23
... run rods from hood to step 3) Cut appropriate size hole in ceiling. limit. Drill holes in all four corners for additional support. (Option B) Attaching hood directly to soffit or duct cover. (Skip to ceiling. 45 Duct Cover Option (VCWH Chimney Wall Hoods) 1 2 Measure distance from ceiling to canopy. 3 Tape to fasten...
... run rods from hood to step 3) Cut appropriate size hole in ceiling. limit. Drill holes in all four corners for additional support. (Option B) Attaching hood directly to soffit or duct cover. (Skip to ceiling. 45 Duct Cover Option (VCWH Chimney Wall Hoods) 1 2 Measure distance from ceiling to canopy. 3 Tape to fasten...
Use and Care Manual
Page 8
Use the same cleaning directions as in case the bulb breaks. Replace the bulb with an R40, 120 volt, 250-watt ...THIS MANUAL SHOULD REMAIN WITH THE HOOD FOR FUTURE REFERENCE. 15 Product Care If you are unable to : VIKING RANGE CORPORATION PREFERRED SERVICE 1803 Hwy 82W Greenwood, Mississippi 38930 USA Record the information indicated below. Cleaning Ductless Venting... will not do the job, use every day household cleaners that you continue to have service problems, contact Viking Range Corporation at 1-888-VIKING1 (845-4641), or write to obtain the name of the authorized service agency...
Use the same cleaning directions as in case the bulb breaks. Replace the bulb with an R40, 120 volt, 250-watt ...THIS MANUAL SHOULD REMAIN WITH THE HOOD FOR FUTURE REFERENCE. 15 Product Care If you are unable to : VIKING RANGE CORPORATION PREFERRED SERVICE 1803 Hwy 82W Greenwood, Mississippi 38930 USA Record the information indicated below. Cleaning Ductless Venting... will not do the job, use every day household cleaners that you continue to have service problems, contact Viking Range Corporation at 1-888-VIKING1 (845-4641), or write to obtain the name of the authorized service agency...
Specs
Page 5
... pressure/air turbulence and greatly reduces performance. DUCTING • Check with ground • 120 VAC/60 Hz • Max. GAS Not applicable ELECTRICAL • Hardwire direct with two-wire with a qualified and trained installer or local codes for general reference only; Without applying static pressure (some brands do not), CFM could...
... pressure/air turbulence and greatly reduces performance. DUCTING • Check with ground • 120 VAC/60 Hz • Max. GAS Not applicable ELECTRICAL • Hardwire direct with two-wire with a qualified and trained installer or local codes for general reference only; Without applying static pressure (some brands do not), CFM could...
Duct Silencer - Installation Instructions
Page 1
...the 10" duct system. The VSIL10 may also be installed as possible. DIMENSIONES All dimensions in accordance with all 4. The VSIL10 is a non-directional device. To achieve the best results locate the VSIL10 as close to reduce perceived ventilation sound level at the range hood. INSTALLING THE VSIL10 1. The...the VSIL10 can be located between the fan inlet and the range hood. Insert the ends of sharp edges. VIKING MODEL VSIL10 IN-LINE FAN SILENCER ONLY FOR USE WITH VIKING 10" DUCT SYSTEMS READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR ...
...the 10" duct system. The VSIL10 may also be installed as possible. DIMENSIONES All dimensions in accordance with all 4. The VSIL10 is a non-directional device. To achieve the best results locate the VSIL10 as close to reduce perceived ventilation sound level at the range hood. INSTALLING THE VSIL10 1. The...the VSIL10 can be located between the fan inlet and the range hood. Insert the ends of sharp edges. VIKING MODEL VSIL10 IN-LINE FAN SILENCER ONLY FOR USE WITH VIKING 10" DUCT SYSTEMS READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR ...