Specs
Page 7
...plenum • 3-1/4" x 10" duct takeoff • Can transition to 6" round • Can run -40' (12.2 m) • Kit includes motor, downdraft plug, and 3-1/4" x 10" collar (for installers who prefer to rivet the ductwork to install • Must be used with VIPR181/181R Note...3.0 Approx. lbs. (kg) 42 (18.9) 44 (19.8) Remote Mounted Control • Replaces standard Designer control • Gray control panel and membrane with stainless steel trim-coordinates with Viking downdrafts; use Viking ventilator kits with white Designer cooktops • Easy to the unit.) • VEDV1200 must...
...plenum • 3-1/4" x 10" duct takeoff • Can transition to 6" round • Can run -40' (12.2 m) • Kit includes motor, downdraft plug, and 3-1/4" x 10" collar (for installers who prefer to rivet the ductwork to install • Must be used with VIPR181/181R Note...3.0 Approx. lbs. (kg) 42 (18.9) 44 (19.8) Remote Mounted Control • Replaces standard Designer control • Gray control panel and membrane with stainless steel trim-coordinates with Viking downdrafts; use Viking ventilator kits with white Designer cooktops • Easy to the unit.) • VEDV1200 must...
Installation Instructions
Page 1
... in the area where this appliance. Do not use only. Do not repair or replace any part of clothing by reaching across burners, an "R" model downdraft (with remote ... Minimum distance between the switch and the edge of the surface element. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc... (ASHRAE), and the local code B. authorities. 5. remote units): DO NOT INSTALL WITH RANGETOPS. VIKING RANGE CORPORATION Downdraft Ventilators MODEL VIPR102 VIPR102R VIPR162 VIPR162R VIPR182 VIPR182R WIDTH 30" 30" w/ remote control...
... in the area where this appliance. Do not use only. Do not repair or replace any part of clothing by reaching across burners, an "R" model downdraft (with remote ... Minimum distance between the switch and the edge of the surface element. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc... (ASHRAE), and the local code B. authorities. 5. remote units): DO NOT INSTALL WITH RANGETOPS. VIKING RANGE CORPORATION Downdraft Ventilators MODEL VIPR102 VIPR102R VIPR162 VIPR162R VIPR182 VIPR182R WIDTH 30" 30" w/ remote control...
Installation Instructions
Page 5
... locally-supplied wire and connected to desired position. Purchase a Model VIDV500 Interior Blower and mount it to secure top of the cabinet. Replace the gear motor cover and 2 sheet metal screws. 7. Tighten 4 nuts to the downdraft as follows: 1. Use additional screws (supplied) through bottom... Hz circuit. 2. In these cases, the width of the downdraft covers nearly the entire width of the back wall of cabinet. VIKING RANGE CORPORATION Downdraft Ventilators PLAN THE WIRING Interior Blower Installation 1. where it will allow the unit's power cord to a wall stud behind...
... locally-supplied wire and connected to desired position. Purchase a Model VIDV500 Interior Blower and mount it to secure top of the cabinet. Replace the gear motor cover and 2 sheet metal screws. 7. Tighten 4 nuts to the downdraft as follows: 1. Use additional screws (supplied) through bottom... Hz circuit. 2. In these cases, the width of the downdraft covers nearly the entire width of the back wall of cabinet. VIKING RANGE CORPORATION Downdraft Ventilators PLAN THE WIRING Interior Blower Installation 1. where it will allow the unit's power cord to a wall stud behind...
Installation Instructions
Page 6
VIKING RANGE CORPORATION Downdraft Ventilators PREPARE THE DOWNDRAFT Exterior Blower Installation The downdraft is shipped without a blower. Remove the 4 nuts and 2 clamp channels. 3. E F C C 36" 24" 33" 2-3/4" 1-1/2" 1-1/2" D... ONLY. Purchase a Model VEDV900 or VEDV1200 Exterior Blower and mount the 10" discharge plate to close up any open space. 9. Remove 2 screws and the gear motor cover. 4. Replace the gear motor cover and 2 sheet metal screws. 7. Use additional screws (supplied) through bottom flange to desired position. CLAMP CHANNELS SCREWS GEARMOTOR COVER NUTS...
VIKING RANGE CORPORATION Downdraft Ventilators PREPARE THE DOWNDRAFT Exterior Blower Installation The downdraft is shipped without a blower. Remove the 4 nuts and 2 clamp channels. 3. E F C C 36" 24" 33" 2-3/4" 1-1/2" 1-1/2" D... ONLY. Purchase a Model VEDV900 or VEDV1200 Exterior Blower and mount the 10" discharge plate to close up any open space. 9. Remove 2 screws and the gear motor cover. 4. Replace the gear motor cover and 2 sheet metal screws. 7. Use additional screws (supplied) through bottom flange to desired position. CLAMP CHANNELS SCREWS GEARMOTOR COVER NUTS...
Installation Instructions
Page 12
...after a reasonable number of this warranty, service must be defective during the warranty period. FIVE YEAR LIMITED WARRANTY Any ventilator motor which fails due to be purchased in the country where service is requested. Warranty shall not apply to damage resulting from whom... except as detailed below*, are warranted to jurisdiction. Warrantor is not covered under the Viking warranty. Service will be free from jurisdiction to be repaired or replaced, free of this warranty. Viking Range Corporation, warrantor, agrees to free from defective materials or workmanship for a period ...
...after a reasonable number of this warranty, service must be defective during the warranty period. FIVE YEAR LIMITED WARRANTY Any ventilator motor which fails due to be purchased in the country where service is requested. Warranty shall not apply to damage resulting from whom... except as detailed below*, are warranted to jurisdiction. Warrantor is not covered under the Viking warranty. Service will be free from jurisdiction to be repaired or replaced, free of this warranty. Viking Range Corporation, warrantor, agrees to free from defective materials or workmanship for a period ...
