User Manual
Page 4
... Your Toshiba Hard Disk Drive can also damage the drive. Use the information in the following table before setting drive as cable select. DRIVE Master Drive Slave Drive Master Drive Slave Drive Slave Drive Prohibit 2 Master configuration is obtained by setting jumpers C-D. High, the drive is "Master", if pin 28...can cause damage. Slave configuration is configured as Master or Slave. LOW HIGH - MK4025GAS (HDD2190) Caution: Your Hard Disk Drive is used for two drive applications. Figure 1.HDD Jumper Locations JUMPER No Jumper C-D Jumper B-D Jumper B-D Jumper A-B Jumper A-C...
... Your Toshiba Hard Disk Drive can also damage the drive. Use the information in the following table before setting drive as cable select. DRIVE Master Drive Slave Drive Master Drive Slave Drive Slave Drive Prohibit 2 Master configuration is obtained by setting jumpers C-D. High, the drive is "Master", if pin 28...can cause damage. Slave configuration is configured as Master or Slave. LOW HIGH - MK4025GAS (HDD2190) Caution: Your Hard Disk Drive is used for two drive applications. Figure 1.HDD Jumper Locations JUMPER No Jumper C-D Jumper B-D Jumper B-D Jumper A-B Jumper A-C...
User Manual
Page 5
Placing Hard Drive inside the drive at a certain level Do not apply any force to the top cover, except the screw areas on top cover. Important Note: Disconnect power from your Computer • Determine mounting configuration (the drive can be mounted in system CMOS • Refer to ...; Install the I/F cable to use ESD proof wrist strap when handling drive. The four mounting screws should be 3.0mm minimum and 3.5mm maximum. Ensure pin 1 is oriented correctly, (pin 1 on the cable is 2N. The drive contains several parts which may be easily damaged by a red or blue...
Placing Hard Drive inside the drive at a certain level Do not apply any force to the top cover, except the screw areas on top cover. Important Note: Disconnect power from your Computer • Determine mounting configuration (the drive can be mounted in system CMOS • Refer to ...; Install the I/F cable to use ESD proof wrist strap when handling drive. The four mounting screws should be 3.0mm minimum and 3.5mm maximum. Ensure pin 1 is oriented correctly, (pin 1 on the cable is 2N. The drive contains several parts which may be easily damaged by a red or blue...
User Manual
Page 11
Interface Pin Assignment DRIVE INTERFACE SIGNALS PIN SIGNAL PIN SIGNAL 1 RESET 2 GROUND 3 DD 7 4 DD 8 5 DD 6 6 DD 9 7 DD 5 8 DD 10 9 DD 4 10 DD 11 11 DD 3 12 DD 12 13 DD 2 14 DD 13 15 ... -DMARDY/- DSTROBE CSEL 29 DMACK 30 GROUND 31 INTRQ 32 IOCS16 33 DA1 34 PDIAG 35 DA0 36 DA 2 37 CS0 38 CS1 39 DASP 40 GROUND 41 +5V (LOGIC) 42 +5V (MOTOR) 43 GROUND 44 RESERVED Note: Symbol () in front of signal indicates negative logic. 9
Interface Pin Assignment DRIVE INTERFACE SIGNALS PIN SIGNAL PIN SIGNAL 1 RESET 2 GROUND 3 DD 7 4 DD 8 5 DD 6 6 DD 9 7 DD 5 8 DD 10 9 DD 4 10 DD 11 11 DD 3 12 DD 12 13 DD 2 14 DD 13 15 ... -DMARDY/- DSTROBE CSEL 29 DMACK 30 GROUND 31 INTRQ 32 IOCS16 33 DA1 34 PDIAG 35 DA0 36 DA 2 37 CS0 38 CS1 39 DASP 40 GROUND 41 +5V (LOGIC) 42 +5V (MOTOR) 43 GROUND 44 RESERVED Note: Symbol () in front of signal indicates negative logic. 9