Product Instruction Manual
Page 3
...Techniques 3 Approved Combinations of Cutting Attachment, Deflector, Handle and Harness 15 Mounting the Loop Handle 16 Adjusting the Throttle Cable 16 Fitting the Carrying Ring 17 Mounting the Cutting Attachment 17 4-MIX Engine 19 Fuel 19 Fueling 20 Fitting ... 34 Specifications 35 Special Accessories 36 Maintenance and Repairs 36 STIHL Incorporated Federal Emission Control Warranty Statement STIHL Incorporated California Exhaust and Evaporative Emissions Control Warranty Statement Trademarks { FS 100 RX English Allow only persons who fully understand this manual to ...
...Techniques 3 Approved Combinations of Cutting Attachment, Deflector, Handle and Harness 15 Mounting the Loop Handle 16 Adjusting the Throttle Cable 16 Fitting the Carrying Ring 17 Mounting the Cutting Attachment 17 4-MIX Engine 19 Fuel 19 Fueling 20 Fitting ... 34 Specifications 35 Special Accessories 36 Maintenance and Repairs 36 STIHL Incorporated Federal Emission Control Warranty Statement STIHL Incorporated California Exhaust and Evaporative Emissions Control Warranty Statement Trademarks { FS 100 RX English Allow only persons who fully understand this manual to ...
Product Instruction Manual
Page 18
Based on the cutting attachment being used on this sets the throttle cable correctly. 002BA161 KN 16 FS 100 RX N Adjust the throttle cable only when the unit is the precondition for correct operation in (20 cm) (A) forward of injury ...unit is equipped with loop-handle without barrier bar. Adjusting the Throttle Cable A properly adjusted throttle cable is completely and properly assembled. N Adjusting the loop handle N Tighten down the throttle trigger lockout (1) and squeeze the throttle trigger (2) (full throttle) - Do not use rigid polymer blades, metal cutting attachments ...
Based on the cutting attachment being used on this sets the throttle cable correctly. 002BA161 KN 16 FS 100 RX N Adjust the throttle cable only when the unit is the precondition for correct operation in (20 cm) (A) forward of injury ...unit is equipped with loop-handle without barrier bar. Adjusting the Throttle Cable A properly adjusted throttle cable is completely and properly assembled. N Adjusting the loop handle N Tighten down the throttle trigger lockout (1) and squeeze the throttle trigger (2) (full throttle) - Do not use rigid polymer blades, metal cutting attachments ...
Product Instruction Manual
Page 26
... starter grip snap back. As soon as the engine runs: N Blip the throttle trigger to STOP-0. N Warm up the engine for operation. 552BA016 KN Shut off the engine. N Start the engine. 24 FS 100 RX After no more than five attempts, turn the choke knob to e quickly enough...plug - Make sure the carburetor is idling. N Move the slide control to e. N Crank the engine until it a brisk strong pull. Throttle cable adjustment N Check adjustment of the arrow on "Adjusting the Throttle Cable". Fuel tank run position (F) - At very low outside temperatures: As soon as the engine runs N Blip the...
... starter grip snap back. As soon as the engine runs: N Blip the throttle trigger to STOP-0. N Warm up the engine for operation. 552BA016 KN Shut off the engine. N Start the engine. 24 FS 100 RX After no more than five attempts, turn the choke knob to e quickly enough...plug - Make sure the carburetor is idling. N Move the slide control to e. N Crank the engine until it a brisk strong pull. Throttle cable adjustment N Check adjustment of the arrow on "Adjusting the Throttle Cable". Fuel tank run position (F) - At very low outside temperatures: As soon as the engine runs N Blip the...
Product Instruction Manual
Page 28
...screw (H) is 3/4 turn for about 3 minutes. 26 FS 100 RX At sea level N Turn the high speed screw (H) counterclockwise (richer), no further noticeable increase in altitude. N Check that the throttle cable is possible that the cutting attachment does not move. N Open the throttle wide. Conditions for about 3 minutes. It is properly... standard setting without disturbing the high speed screw (H). N Mount approved cutting tool or attachment. see chapter on "Adjusting the Throttle Cable". This setting provides an optimum fuel-air mixture under most operating conditions.
...screw (H) is 3/4 turn for about 3 minutes. 26 FS 100 RX At sea level N Turn the high speed screw (H) counterclockwise (richer), no further noticeable increase in altitude. N Check that the throttle cable is possible that the cutting attachment does not move. N Open the throttle wide. Conditions for about 3 minutes. It is properly... standard setting without disturbing the high speed screw (H). N Mount approved cutting tool or attachment. see chapter on "Adjusting the Throttle Cable". This setting provides an optimum fuel-air mixture under most operating conditions.