Ryobi RLS1351 Support and Manuals
Get Help and Manuals for this Ryobi item
View All Support Options Below
Free Ryobi RLS1351 manuals!
Problems with Ryobi RLS1351?
Ask a Question
Free Ryobi RLS1351 manuals!
Problems with Ryobi RLS1351?
Ask a Question
Most Recent Ryobi RLS1351 Questions
Blade Rotational Direction.
I am not able to cut hardwood from my Ryobi RLS1351. I don't have any problem cutting laminate floor...
I am not able to cut hardwood from my Ryobi RLS1351. I don't have any problem cutting laminate floor...
(Posted by bymatias 11 years ago)
Popular Ryobi RLS1351 Manual Pages
Operation Manual - Page 3
... using your extension cord is damaged must be properly repaired or replaced by the cord or yank it was designed.
&#...service center to disconnect from tool before servicing, or when changing attachments, blades, bits, cutters, etc., all instructions listed below, may result in electric shock, fire and/or serious personal injury. Sharp blades minimize stalling and kickback.
Blade...
Operation Manual - Page 4
...; When servicing use blades with the accessory.
DOUBLE CHECK ALL SETUPS. Do not change the plug in this tool has a polarized plug (one way. Do not rush.
DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by a qualified service technician at an authorized service facility. Instructions for...
Operation Manual - Page 5
...parts replaced before resuming operation.
Always stay alert! Do not reach underneath work and when required. NEVER leave the saw unattended while connected to see the work clamp to full speed before changing blade or servicing. e) Never reach around or over saw blade...them frequently and use of the saw ) to instruct other users. Wait for saw table at a time. b) Keep ...
Operation Manual - Page 8
... the front of the saw blade tooth is bent (or set) outward from the face of the workpiece.
Worktable Surface where the workpiece rests while performing a cutting, drilling, planing, or sanding operation.
8 Compound Cut A cross cut without the workpiece being guided by a spinning object in one minute. Push Sticks (flooring and table saws) Device used to help...
Operation Manual - Page 9
... guard adjustment knob.
FEATURES
PRODUCT SPECIFICATIONS
Blade Diameter 5 in . Rip Capacity 8 in .
A 5 in . It will cut materials up to the table at the desired cutting angle. thick.
BLADE GUARD -
Set the clearance of kickback.
A blade wrench is included with rip cuts) - One end of the saw
See Figure 1, page 17.
Carrying Handle - FENCE - MITER GROOVE...
Operation Manual - Page 10
... a workbench or mounting boards.
TO install the Foot/Blade Wrench holder
See Figure 4, page 18. Align holes in a hazardous condition leading to the product by an authorized service center.
Any such alteration or modification is factory set for use this product if any parts are damaged or missing do not operate this list are replaced.
Operation Manual - Page 12
... spindle locks. Using the blade wrench provided, loosen and remove
the blade bolt. Never use a blade that is removed from beneath the saw base by wrapping it before placing blade on the side of the blade pointing up and back to install/replace the blade. Unplug the saw has a convenient storage area specifically designed for the push stick (on...
Operation Manual - Page 13
...blade. Clean the saw, blade guard, under the throat plate, and any areas where saw : Press the switch down to inflict serious injury. Use push blocks for the purpose listed below: Cutting laminate, engineered, and solid, hardwood floor... the anti-kickback pawls may be effective. Always guide your saw dust or scrap workpieces may gather. Use the ...
Operation Manual - Page 14
...of the blade guard is in the off and leave the cut (kerf) on the workpiece. Turn the saw is not in .
Set the ...parts away from the release lever while continuing to power source. Making CUTS
This saw usage and specialized woodworking procedures for making rip cuts. Your local library has many books on the saw
table. Loosen the indicator screw. Align the saw...
Operation Manual - Page 15
...; Install the work .
Turn the saw on the saw.
When ripping a long workpiece, place a support the same height as the table surface behind the saw for the cut position (see page 11)
and set at 0°. Tighten the clamp knob securely. Pull out the lock pin and push the saw to the rear of the blade...
Repair Sheet - Page 2
MODEL NUMBER RLS1351 FIGURE A
15 14
20 16 17
4
18 19
56
23 22 14 14
18 19 20
18 21 26
22 72
24
25
27
74
28 29
30
31
8
9 10
3
11 12
13
2
1 38
61 60 62
7
56
54 53
55
57
59
58
49 50
52 51
63
65
64 66
67
68
71 56
69
70
2
33 29 32
29 32
73 42 43
35
34
44
40
37 36 38
39
41
45
46 47 48
SEE FIGURE B RYOBI 5 in. FLOORING SAW -
Repair Sheet - Page 3
... Washer (D14 x D5.2 x 2t 1
48 089230100044 Screw (M5 x 35 mm 1
49 089230100052
Inner Blade Washer 1
50 089230100053 Saw Blade (D5/8 in. × D5 in . Always mention the model number in all correspondence regarding your TILE SAW or when ordering repair parts. NUMBER
DESCRIPTION
QTY.
1 089230100063 Power Cord 1 2 089230100062 Bend Relief 1 3 089230100703 Armature Assembly (Inc...
Repair Sheet - Page 4
RYOBI 5 in. MODEL NUMBER RLS1351
FIGURE B
5 46 45
44
52
51
50
47
49
53 51
43
36
42
41
48
40
54
44
35
39
32
34
SEE FIGURE A
30
1
29
28
26 27
33 37
55
38
43 42
5
20
41
4
5
37 37 31 33
21
2
19
3
3
5
23
18
24
22
17
5
4
14 13
16
15 13 25
7 6
9
8
10
10
11
11
10
10
11
11
12
12
12 12
4 FLOORING SAW -
Repair Sheet - Page 5
...NO. NUMBER
DESCRIPTION
QTY. RYOBI 5 in all correspondence regarding your TILE SAW or when ordering repair parts. FLOORING SAW -
Hd 3 34 089230100094 Carriage Plate 1 35 089230100088 Handle 1 36 089230100081 Screw (M6 × 16 mm 2 37 089230100089 Lock Washer (D6 6 38 089230100092 Screw (M6 × 18 mm, Soc. MODEL NUMBER RLS1351
The model number will be found on...
Repair Sheet - Page 6
FLOORING SAW - MODEL NUMBER RLS1351 MOTOR ASSEMBLY
BLACK
BLACK BLACK
BLACK WHITE
BLACK
POWER CORD
SWITCH
WIRING DIAGRAM
6 RYOBI 5 in.
Ryobi RLS1351 Reviews
We have not received any reviews for Ryobi yet.