Installation Guide
Page 3
Contents Important safety instructions 4 Limitation of liability 5 Disclaimer of warranty 5 Preface 5 Features 6 About the user manuals 6 Trademarks and registered trademarks 6 Precautions 7 Major operating controls 9 Precautions for installation 10 DIP switch settings 12 ■ Communication Parameters (DIP Switch 2 12 ■ Unit Number (DIP Switch 1 13 ■ RS485 Communication Parameters (DIP Switch 1 15 Installation 16 ■ Mounting the Camera 16 Connections 20 Troubleshooting 22 Specifications 26 Standard accessories 27 Optional accessories 27 3
Contents Important safety instructions 4 Limitation of liability 5 Disclaimer of warranty 5 Preface 5 Features 6 About the user manuals 6 Trademarks and registered trademarks 6 Precautions 7 Major operating controls 9 Precautions for installation 10 DIP switch settings 12 ■ Communication Parameters (DIP Switch 2 12 ■ Unit Number (DIP Switch 1 13 ■ RS485 Communication Parameters (DIP Switch 1 15 Installation 16 ■ Mounting the Camera 16 Connections 20 Troubleshooting 22 Specifications 26 Standard accessories 27 Optional accessories 27 3
Installation Guide
Page 7
... flammable gases. Do not use will deteriorate, causing the product to observe this product in injury or accidents. 7 Use the specified mount bracket. Failure to observe this product, continued use this may cause electric shock, short circuit, or fire. Failure to observe this ... product shall be started after sufficient reinforcement. Failure to damage by explosion. Do not insert any foreign objects. Tighten screws and mounting fixtures to consult the dealer. Precautions The following points as well as a pedestal. Refer installation work to ensure that is subject...
... flammable gases. Do not use will deteriorate, causing the product to observe this product in injury or accidents. 7 Use the specified mount bracket. Failure to observe this product, continued use this may cause electric shock, short circuit, or fire. Failure to observe this ... product shall be started after sufficient reinforcement. Failure to damage by explosion. Do not insert any foreign objects. Tighten screws and mounting fixtures to consult the dealer. Precautions The following points as well as a pedestal. Refer installation work to ensure that is subject...
Installation Guide
Page 10
...on a ceiling or wall, except for accidents caused by fault in the camera, Panasonic holds absolutely no responsibility for injuries or property damage resulting from falling, attach the safety wire to the mounting bracket or the anchor bolt before starting to install the camera to observe this product... as the contents of the dome cover after the installation is strong enough for use the optionally available (WV-Q122) Wall Mount Bracket. You need to unsuitable installation. Approx. 4 823 N 4.5 kg WV-Q122 2 kg On wall M8 pieces {84 kgf} 10 • Ensure that it is not in...
...on a ceiling or wall, except for accidents caused by fault in the camera, Panasonic holds absolutely no responsibility for injuries or property damage resulting from falling, attach the safety wire to the mounting bracket or the anchor bolt before starting to install the camera to observe this product... as the contents of the dome cover after the installation is strong enough for use the optionally available (WV-Q122) Wall Mount Bracket. You need to unsuitable installation. Approx. 4 823 N 4.5 kg WV-Q122 2 kg On wall M8 pieces {84 kgf} 10 • Ensure that it is not in...
Installation Guide
Page 11
...of the installation area. • Do not use in an extremely lowtemperature environment below -30 °C, snow and frost may not be mounted. That may make surveillance images inviewable. (The extent of the devices to be obtained immediately after startup. Before connections, check the ratings...(2) Influence by snowfall Due to the surface. Prepare the screws according to the material, structure, strength and other factors of the mounting area and the total weight of devices are not supplied with an appropriate tightening torque according to ensure tightening is enough and there...
...of the installation area. • Do not use in an extremely lowtemperature environment below -30 °C, snow and frost may not be mounted. That may make surveillance images inviewable. (The extent of the devices to be obtained immediately after startup. Before connections, check the ratings...(2) Influence by snowfall Due to the surface. Prepare the screws according to the material, structure, strength and other factors of the mounting area and the total weight of devices are not supplied with an appropriate tightening torque according to ensure tightening is enough and there...
Installation Guide
Page 16
... thread) 16 (60) 25 85 REAR START LOCK Housing Base Camera The screws that the place you are accessory of the camera mounted on a wall with the optional WV-Q122 Wall Mount Bracket. See instructions included with the optional bracket STEP 1 Attach the camera to 7 in the reverse order. STEP 2 To detach the...
... thread) 16 (60) 25 85 REAR START LOCK Housing Base Camera The screws that the place you are accessory of the camera mounted on a wall with the optional WV-Q122 Wall Mount Bracket. See instructions included with the optional bracket STEP 1 Attach the camera to 7 in the reverse order. STEP 2 To detach the...
Installation Guide
Page 17
... Housing Base REAR REAR STEP 7 (1) Check that water or moisture cannot get inside the camera it from the housing base by loosening 4 screws. * S pecial screw (mounting screw): Use a hexagon wrench for details. See instructions of the leaf spring on the housing base faces the wall. (Recommended tightening torque: 2.45 N·m {25...
... Housing Base REAR REAR STEP 7 (1) Check that water or moisture cannot get inside the camera it from the housing base by loosening 4 screws. * S pecial screw (mounting screw): Use a hexagon wrench for details. See instructions of the leaf spring on the housing base faces the wall. (Recommended tightening torque: 2.45 N·m {25...
Installation Guide
Page 18
... is fixed. Safety wire Main sunshield For loss prevention, one side of the front and rear sun-shields to the housing mounting base. View from the bottom, to the position that covers the housing base. Securely tighten the screws* that were removed when the ...housing mounting base was removed. (Recommended tightening torque: 2.45 N·m {25 kgf·cm}) * Special screw (mounting screw) Use a hexagon wrench for the hexagon screw (M5). Housing Base START LOCK Front and ...
... is fixed. Safety wire Main sunshield For loss prevention, one side of the front and rear sun-shields to the housing mounting base. View from the bottom, to the position that covers the housing base. Securely tighten the screws* that were removed when the ...housing mounting base was removed. (Recommended tightening torque: 2.45 N·m {25 kgf·cm}) * Special screw (mounting screw) Use a hexagon wrench for the hexagon screw (M5). Housing Base START LOCK Front and ...
Installation Guide
Page 27
... OFF (1/50), AUTO, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 32X max. each Front/rear sunshield fixing screw 2 pcs. (incl. 1 spare) Optional accessories Wall Mount Bracket WV-Q122 27 Installation Guide (this book 1 pc. *The CD-ROM contains the operating instructions (PDF). The following parts are used during installation procedures. Front and...
... OFF (1/50), AUTO, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 32X max. each Front/rear sunshield fixing screw 2 pcs. (incl. 1 spare) Optional accessories Wall Mount Bracket WV-Q122 27 Installation Guide (this book 1 pc. *The CD-ROM contains the operating instructions (PDF). The following parts are used during installation procedures. Front and...