Installation Guide
Page 2
... or utility sink, sump pump and connectors (available from local plumbing suppliers) 2" (51 mm) diameter to 19⁄16" (39.5 mm) Optional tools: Flashlight Bucket Parts needed : Adjustable or open end wrenches 1/2" (13 mm) and 9/16" (14 mm) 4" min (102 mm) Level Wood block Ruler or measuring tape Pliers that open...
... or utility sink, sump pump and connectors (available from local plumbing suppliers) 2" (51 mm) diameter to 19⁄16" (39.5 mm) Optional tools: Flashlight Bucket Parts needed : Adjustable or open end wrenches 1/2" (13 mm) and 9/16" (14 mm) 4" min (102 mm) Level Wood block Ruler or measuring tape Pliers that open...
Installation Guide
Page 4
... 4 Floor drain system requires a Siphon Break Kit (Part Number 285834), 2 Connector Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that may be needed . See "Alternate Parts". Always secure drain hose with cable tie. See "Alternate Parts". Floor drain system 4.5" (114 mm) See requirements ...tub must be at least 30" (762 mm) above floor; If you need to 1" (25 mm) diameter Standpipe Adapter Kit is available (Part Number 3363920). Top of washer. ** Recommended 4" (102 mm), minimum 1.5" (38 mm) DRAIN SYSTEM Drain system can be installed using a...
... 4 Floor drain system requires a Siphon Break Kit (Part Number 285834), 2 Connector Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that may be needed . See "Alternate Parts". Always secure drain hose with cable tie. See "Alternate Parts". Floor drain system 4.5" (114 mm) See requirements ...tub must be at least 30" (762 mm) above floor; If you need to 1" (25 mm) diameter Standpipe Adapter Kit is available (Part Number 3363920). Top of washer. ** Recommended 4" (102 mm), minimum 1.5" (38 mm) DRAIN SYSTEM Drain system can be installed using a...
Installation Guide
Page 6
...service center to avoid suspension and structural damage, a certified technician must properly set up washer for relocation. 6 C over top Loosen bolts with washer parts. 5. IMPORTANT: Do not plug washer in place on cabinet back with four transport bolt hole plugs included with a 1/2" (13 mm) wrench.... You may need additional parts with clamp. NOTE: If washer is not already in until installation has been completed. 3. Place power cord over bolt holes with pliers ...
...service center to avoid suspension and structural damage, a certified technician must properly set up washer for relocation. 6 C over top Loosen bolts with washer parts. 5. IMPORTANT: Do not plug washer in place on cabinet back with four transport bolt hole plugs included with a 1/2" (13 mm) wrench.... You may need additional parts with clamp. NOTE: If washer is not already in until installation has been completed. 3. Place power cord over bolt holes with pliers ...
Installation Guide
Page 7
...to help in attaching hoses to work properly. Washer must be used. Drain hose form must be inside standpipe; Damage can result. See "Alternate Parts". 9. Place drain hose in picture) or over each other when attached correctly. 12. IMPORTANT: Only 4.5" (114 mm) of laundry tub. ... IMPORTANT: To avoid leaks, check that your water inlet hoses have flat washers at both ends. In most standard configurations, hoses will need additional parts with the hose labeled cold for a few seconds through hoses into a laundry tub, drainpipe, or bucket to water faucets 4.5" (114 mm) ...
...to help in attaching hoses to work properly. Washer must be used. Drain hose form must be inside standpipe; Damage can result. See "Alternate Parts". 9. Place drain hose in picture) or over each other when attached correctly. 12. IMPORTANT: Only 4.5" (114 mm) of laundry tub. ... IMPORTANT: To avoid leaks, check that your water inlet hoses have flat washers at both ends. In most standard configurations, hoses will need additional parts with the hose labeled cold for a few seconds through hoses into a laundry tub, drainpipe, or bucket to water faucets 4.5" (114 mm) ...
Installation Guide
Page 9
... contact with wooden block. Tighten leveling feet Electrical Shock Hazard Plug into a grounded 3 prong outlet. q Check that washer is an extra part, go back through steps to turn jam nuts clockwise on leveling feet tightly against washer cabinet. q Check that both hot and cold hoses ... back of washer. Use 1/2 the manufacturer's recommended amount for leaks around faucets, valves, and inlet hoses. q Check that you have all parts are on washer. q Read "Using Your Washer" in your washer, press power and choose the QUICK WASH cycle and run it without clothes.
... contact with wooden block. Tighten leveling feet Electrical Shock Hazard Plug into a grounded 3 prong outlet. q Check that washer is an extra part, go back through steps to turn jam nuts clockwise on leveling feet tightly against washer cabinet. q Check that both hot and cold hoses ... back of washer. Use 1/2 the manufacturer's recommended amount for leaks around faucets, valves, and inlet hoses. q Check that you have all parts are on washer. q Read "Using Your Washer" in your washer, press power and choose the QUICK WASH cycle and run it without clothes.
Dimension Guide
Page 2
...specifications without notice. IMPORTANT: To avoid siphoning, only 4.5" (114 mm) of washer. See "Alternate Parts". Floor drain system 4.5" (114 mm) See requirements for a standpipe drain: 2" (51 mm). See "Alternate Parts". Custom cabinet installation (washer only): 7" (178 mm) 14" (356 mm) All dimensions show.... For each arrangement, consider allowing more space for ease of washer to 1" (25 mm) diameter Standpipe Adapter Kit is available (Part Number 3363920). Add spacing of 1" (25 mm) on all sides of installation and servicing, and spacing for companion appliances and clearances...
...specifications without notice. IMPORTANT: To avoid siphoning, only 4.5" (114 mm) of washer. See "Alternate Parts". Floor drain system 4.5" (114 mm) See requirements for a standpipe drain: 2" (51 mm). See "Alternate Parts". Custom cabinet installation (washer only): 7" (178 mm) 14" (356 mm) All dimensions show.... For each arrangement, consider allowing more space for ease of washer to 1" (25 mm) diameter Standpipe Adapter Kit is available (Part Number 3363920). Add spacing of 1" (25 mm) on all sides of installation and servicing, and spacing for companion appliances and clearances...
Use & Care Guide
Page 25
...instructions attached to or furnished with the product, Maytag will pay for factory specified parts and repair labor to correct defects in remote locations where an authorized Maytag servicer is required to obtain service under these parts that prevent function of Whirlpool Corporation or Whirlpool ...maintenance or installation, installation not in materials and workmanship and is a limited 10 year warranty on how to Maytag within 30 days. 9. Service or parts for warranty service to or furnished with original model/serial numbers removed, altered, or not easily determined. ...
...instructions attached to or furnished with the product, Maytag will pay for factory specified parts and repair labor to correct defects in remote locations where an authorized Maytag servicer is required to obtain service under these parts that prevent function of Whirlpool Corporation or Whirlpool ...maintenance or installation, installation not in materials and workmanship and is a limited 10 year warranty on how to Maytag within 30 days. 9. Service or parts for warranty service to or furnished with original model/serial numbers removed, altered, or not easily determined. ...
Warranty Information
Page 1
... of the problem n Proof of God, or use your authorized Maytag dealer to access additional resources, or visit https://www.maytag.com/product_help. 2. Before contacting us to obtain service under these parts that existed when this major appliance was purchased. In the U.S. ...or humidity, or exposure to you . PROOF OF PURCHASE IS REQUIRED TO OBTAIN WARRANTY SERVICE. Consumable parts (i.e. DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY Maytag makes no representations about buying an extended warranty. Please take a few minutes to review the Troubleshooting or...
... of the problem n Proof of God, or use your authorized Maytag dealer to access additional resources, or visit https://www.maytag.com/product_help. 2. Before contacting us to obtain service under these parts that existed when this major appliance was purchased. In the U.S. ...or humidity, or exposure to you . PROOF OF PURCHASE IS REQUIRED TO OBTAIN WARRANTY SERVICE. Consumable parts (i.e. DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY Maytag makes no representations about buying an extended warranty. Please take a few minutes to review the Troubleshooting or...