Installation Guide
Page 2
... hose, Black EPDM, space saving 90° elbow, hypro-blue steel couplings (2 pack) Cable tie 2 Transport bolt hole plugs (4) INSTALLATION REQUIREMENTS TOOLS AND PARTS Gather required tools and parts before starting installation. Tools needed: Adjustable or open end wrenches 1/2" (13 mm) and 9/16" (14 mm) 4" min (102 mm) Level Wood block Ruler...
... hose, Black EPDM, space saving 90° elbow, hypro-blue steel couplings (2 pack) Cable tie 2 Transport bolt hole plugs (4) INSTALLATION REQUIREMENTS TOOLS AND PARTS Gather required tools and parts before starting installation. Tools needed: Adjustable or open end wrenches 1/2" (13 mm) and 9/16" (14 mm) 4" min (102 mm) Level Wood block Ruler...
Installation Guide
Page 4
...system. 4 Floor drain system requires a Siphon Break Kit (Part Number 285834), 2 Connector Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that may be at least 30" (762 mm) high; See "Alternate Parts". Recessed area or closet installation (washer only): 3" (76 ... 4" (102 mm), minimum 1.5" (38 mm) DRAIN SYSTEM Drain system can be purchased separately. Always secure drain hose with cable tie. See "Alternate Parts". install no higher than 96" (2.44 m), a sump pump and associated hardware are needed .) Floor drain system 4.5" (114 mm) See requirements for ...
...system. 4 Floor drain system requires a Siphon Break Kit (Part Number 285834), 2 Connector Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that may be at least 30" (762 mm) high; See "Alternate Parts". Recessed area or closet installation (washer only): 3" (76 ... 4" (102 mm), minimum 1.5" (38 mm) DRAIN SYSTEM Drain system can be purchased separately. Always secure drain hose with cable tie. See "Alternate Parts". install no higher than 96" (2.44 m), a sump pump and associated hardware are needed .) Floor drain system 4.5" (114 mm) See requirements for ...
Installation Guide
Page 6
...holes with transport bolt hole plugs Remove the yellow shipping strap from back of drain hose, squeeze clamp with attached cap. You may need additional parts with a 1/2" (13 mm) wrench. Pull power cord through opening in until installation has been completed. NOTE: If washer is not already ...back with four transport bolt hole plugs included with clamp. For a floor drain, remove the preinstalled drain hose form as shown. See "Alternate Parts". CONNECT DRAIN HOSE 7. 3. Slide each bolt and spacer to back of hose, centering it over top of washer to allow free access to...
...holes with transport bolt hole plugs Remove the yellow shipping strap from back of drain hose, squeeze clamp with attached cap. You may need additional parts with a 1/2" (13 mm) wrench. Pull power cord through opening in until installation has been completed. NOTE: If washer is not already ...back with four transport bolt hole plugs included with clamp. For a floor drain, remove the preinstalled drain hose form as shown. See "Alternate Parts". CONNECT DRAIN HOSE 7. 3. Slide each bolt and spacer to back of hose, centering it over top of washer to allow free access to...
Installation Guide
Page 7
...installations only) CONNECT INLET HOSES 10. Do not use hoses without washers. 11. Use pliers to avoid clogs. Damage can result. See "Alternate Parts". 9. Washer IMPORTANT: To avoid leaks, check that your water inlet hoses have flat washers at both ends. Washer must be used. Screw on... coupling by hand until clear. 7 Attach the hose labeled hot to faucets or washer. In most standard configurations, hoses will need additional parts with flat washers (not provided). You may need to help in picture) or over each other when attached correctly. 12. Do not ...
...installations only) CONNECT INLET HOSES 10. Do not use hoses without washers. 11. Use pliers to avoid clogs. Damage can result. See "Alternate Parts". 9. Washer IMPORTANT: To avoid leaks, check that your water inlet hoses have flat washers at both ends. Washer must be used. Screw on... coupling by hand until clear. 7 Attach the hose labeled hot to faucets or washer. In most standard configurations, hoses will need additional parts with flat washers (not provided). You may need to help in picture) or over each other when attached correctly. 12. Do not ...
Installation Guide
Page 9
...of your tools. Repeat as needed. Do not use an extension cord. Do not use an adapter. q Check that you have all of /recycle all parts are about 4" (102 mm) with wooden block. q Read "Using Your Washer" in contact with the floor. Use 1/2 the manufacturer's recommended amount for.... Tighten leveling feet Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. q Check that washer is an extra part, go back through steps to prop up front of washer about 1/2" (13 mm) from console and any tape remaining on leveling feet tightly against washer...
...of your tools. Repeat as needed. Do not use an extension cord. Do not use an adapter. q Check that you have all of /recycle all parts are about 4" (102 mm) with wooden block. q Read "Using Your Washer" in contact with the floor. Use 1/2 the manufacturer's recommended amount for.... Tighten leveling feet Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. q Check that washer is an extra part, go back through steps to prop up front of washer about 1/2" (13 mm) from console and any tape remaining on leveling feet tightly against washer...
Use & Care Guide
Page 23
...installed, operated, and maintained according to instructions attached to or furnished with the product, Maytag brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "Maytag") will pay for factory specified parts and repair labor to correct defects in materials or workmanship that interfere with servicing, removal..., or replacement of God, or use with the product, Maytag will pay for factory specified parts for in the United States or Canada and applies only when the major appliance is a limited 10 year warranty...
...installed, operated, and maintained according to instructions attached to or furnished with the product, Maytag brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "Maytag") will pay for factory specified parts and repair labor to correct defects in materials or workmanship that interfere with servicing, removal..., or replacement of God, or use with the product, Maytag will pay for factory specified parts for in the United States or Canada and applies only when the major appliance is a limited 10 year warranty...
Dimension Guide
Page 2
... each arrangement, consider allowing more space for ease of laundry tub must be provided. or 20-amp, fused electrical supply is available (Part Number 3363920). Always secure drain hose with product. Minimum carry-away capacity: 17 gal. (64 L) per minute. If you need ... spacing for companion appliances and clearances for planning purposes only. Floor drain system requires a Siphon Break Kit (Part Number 285834), 2 Connector Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that a separate circuit serving only this appliance be at least 30" (762 mm) high...
... each arrangement, consider allowing more space for ease of laundry tub must be provided. or 20-amp, fused electrical supply is available (Part Number 3363920). Always secure drain hose with product. Minimum carry-away capacity: 17 gal. (64 L) per minute. If you need ... spacing for companion appliances and clearances for planning purposes only. Floor drain system requires a Siphon Break Kit (Part Number 285834), 2 Connector Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that a separate circuit serving only this appliance be at least 30" (762 mm) high...
Warranty Information
Page 1
...major appliance and that vary from state to state or province to correct product damage or defects caused by a Maytag designated service company. Repairs to parts or systems to province. Discoloration, rust, or oxidation of appliance doors. 6. Travel or transportation expenses for ... applies. This product is installed, operated, and maintained according to instructions attached to or furnished with the product, Maytag will pay for factory specified parts for the following information available when you call the Customer eXperience Center: n Name, address, and telephone number n...
...major appliance and that vary from state to state or province to correct product damage or defects caused by a Maytag designated service company. Repairs to parts or systems to province. Discoloration, rust, or oxidation of appliance doors. 6. Travel or transportation expenses for ... applies. This product is installed, operated, and maintained according to instructions attached to or furnished with the product, Maytag will pay for factory specified parts for the following information available when you call the Customer eXperience Center: n Name, address, and telephone number n...