Owners Manual
Page 22
... filters. LIMITATION OF REMEDIES; If you think you on major appliances with the product, Maytag brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "Maytag") will pay for factory specified parts and repair labor to correct defects in materials or workmanship that existed when this limited warranty... only in the United States or Canada and applies only when the major appliance is reported to Maytag within the United States of your major appliance if it was purchased. Replacement parts or repair labor on how to use of products not approved by an authorized...
... filters. LIMITATION OF REMEDIES; If you think you on major appliances with the product, Maytag brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "Maytag") will pay for factory specified parts and repair labor to correct defects in materials or workmanship that existed when this limited warranty... only in the United States or Canada and applies only when the major appliance is reported to Maytag within the United States of your major appliance if it was purchased. Replacement parts or repair labor on how to use of products not approved by an authorized...
Installation Instructions
Page 2
...back page of your Use and Care Guide. Please contact your washer. To order, please refer to 19⁄16" (39.5 mm) Parts supplied: NOTE: All parts supplied for your retailer for some installations, not supplied with washer) n 8212656RP 10 ft. (3.0 m) Inlet hose, Black EPDM (2 pack... (1.8 m) Inlet hose, Black EPDM, space saving 90° elbow, hypro-blue steel couplings (2 pack) 2 INSTALLATION REQUIREMENTS Tools and Parts Gather required tools and parts before starting installation. If you have: You will need: Overhead sewer Standard 20 gal. (76 L) 39" (990 mm) tall drain ...
...back page of your Use and Care Guide. Please contact your washer. To order, please refer to 19⁄16" (39.5 mm) Parts supplied: NOTE: All parts supplied for your retailer for some installations, not supplied with washer) n 8212656RP 10 ft. (3.0 m) Inlet hose, Black EPDM (2 pack... (1.8 m) Inlet hose, Black EPDM, space saving 90° elbow, hypro-blue steel couplings (2 pack) 2 INSTALLATION REQUIREMENTS Tools and Parts Gather required tools and parts before starting installation. If you have: You will need: Overhead sewer Standard 20 gal. (76 L) 39" (990 mm) tall drain ...
Installation Instructions
Page 4
...no higher than 96" (2.44 m) from bottom of washer. install no higher than 96" (2.44 m) from bottom of washer. See "Alternative Parts". Always secure drain hose with beaded tie strap. Minimum diameter for floor standpipe drain system. 4 A 1/4" (6 mm) diameter to pump higher than... 96 inches, a sump pump and associated hardware are needed .) See requirements for a standpipe drain: 2" (51 mm). See "Alternative Parts". DRAIN SYSTEM Drain system can be purchased separately. Floor standpipe drain system 41/2" (113 mm) Laundry tub drain system 41/2" (113 mm) min. ...
...no higher than 96" (2.44 m) from bottom of washer. install no higher than 96" (2.44 m) from bottom of washer. See "Alternative Parts". Always secure drain hose with beaded tie strap. Minimum diameter for floor standpipe drain system. 4 A 1/4" (6 mm) diameter to pump higher than... 96 inches, a sump pump and associated hardware are needed .) See requirements for a standpipe drain: 2" (51 mm). See "Alternative Parts". DRAIN SYSTEM Drain system can be purchased separately. Floor standpipe drain system 41/2" (113 mm) Laundry tub drain system 41/2" (113 mm) min. ...
Installation Instructions
Page 6
Pull bolts and plastic spacers from washer 6. C over top Loosen bolts with attached cap. You may need additional parts with transport bolt hole plugs Remove the yellow shipping strap from the cord. NOTE: If washer is not already in place on cabinet back... to center of washer. For a floor drain, remove the preinstalled drain hose form as shown. See "Alternative Parts". R emove transport bolts from back of drain hose onto drain port and secure with washer parts. 5. Connect Drain Hose 7. Discard bolts and spacers. 4. Attach drain hose to drain port Ribs Close bolt holes...
Pull bolts and plastic spacers from washer 6. C over top Loosen bolts with attached cap. You may need additional parts with transport bolt hole plugs Remove the yellow shipping strap from the cord. NOTE: If washer is not already in place on cabinet back... to center of washer. For a floor drain, remove the preinstalled drain hose form as shown. See "Alternative Parts". R emove transport bolts from back of drain hose onto drain port and secure with washer parts. 5. Connect Drain Hose 7. Discard bolts and spacers. 4. Attach drain hose to drain port Ribs Close bolt holes...
Installation Instructions
Page 7
NOTE: Both hoses must be used. See "Alternative Parts". 9. Drain hose form must be inside standpipe; Attach hose to faucets or washer. Repeat this step with flat washers. Water should be attached and have ... installations, you will cross over side of laundry tub. IMPORTANT: Only 4.5" (113 mm) of the drain hose. In most standard configurations, hoses will need additional parts with separate directions. Do not use tape or sealants on valve when attaching to hot water faucet. You may need to water faucets with new...
NOTE: Both hoses must be used. See "Alternative Parts". 9. Drain hose form must be inside standpipe; Attach hose to faucets or washer. Repeat this step with flat washers. Water should be attached and have ... installations, you will cross over side of laundry tub. IMPORTANT: Only 4.5" (113 mm) of the drain hose. In most standard configurations, hoses will need additional parts with separate directions. Do not use tape or sealants on valve when attaching to hot water faucet. You may need to water faucets with new...
Installation Instructions
Page 9
... faucets, valves, and inlet hoses. Adjust leveling feet Jam nut If washer is plugged into a grounded 3 prong outlet Jam nut When washer is an extra part, go back through steps to raise the washer. 17. Repeat as needed. HELPFUL TIP: You may want to turn jam nuts counterclockwise on feet until...-size load. 9 q Check that washer is not level, use a 9/16" or 14 mm open -end or adjustable wrench to prop up front of /recycle all parts are on washer. q Dispose of washer about 1/2" (13 mm) from console and any tape remaining on . Use only HE detergent.
... faucets, valves, and inlet hoses. Adjust leveling feet Jam nut If washer is plugged into a grounded 3 prong outlet Jam nut When washer is an extra part, go back through steps to raise the washer. 17. Repeat as needed. HELPFUL TIP: You may want to turn jam nuts counterclockwise on feet until...-size load. 9 q Check that washer is not level, use a 9/16" or 14 mm open -end or adjustable wrench to prop up front of /recycle all parts are on washer. q Dispose of washer about 1/2" (13 mm) from console and any tape remaining on . Use only HE detergent.