Installation Guide
Page 4
... without riser Parts supplied (steam models): Tin snips (new vent installations) 1/4"( 6 mm) nut driver (recommended) Tape measure Pliers 4 "Y" connector 2' (0.6 m) inlet hose 5' (1.52 m) Inlet Hose Rubber washer Remove parts package from whom you purchased your "Use and Care Guide." INSTALLATION REQUIREMENTS TOOLS AND PARTS Gather the required tools and parts before purchasing...
... without riser Parts supplied (steam models): Tin snips (new vent installations) 1/4"( 6 mm) nut driver (recommended) Tape measure Pliers 4 "Y" connector 2' (0.6 m) inlet hose 5' (1.52 m) Inlet Hose Rubber washer Remove parts package from whom you purchased your "Use and Care Guide." INSTALLATION REQUIREMENTS TOOLS AND PARTS Gather the required tools and parts before purchasing...
Installation Guide
Page 5
... 20-100 psi (137.9-689.6 kPa). The dryer must not be large enough to allow the dryer door to water and/or weather. Contact your washer using power supply cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves, and water pressure of 5" (127 mm) clearance behind dryer for...
... 20-100 psi (137.9-689.6 kPa). The dryer must not be large enough to allow the dryer door to water and/or weather. Contact your washer using power supply cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves, and water pressure of 5" (127 mm) clearance behind dryer for...
Installation Guide
Page 12
... (14.6 m) 2 Rigid metal 44 ft. (13.4 m) 38 ft. (11.6 m) 3 Rigid metal 35 ft. (10.7 m) 29 ft. (8.8 m) 4 Rigid metal 27 ft. (8.2 m) 21 ft. (6.4 m) Maytag Vent System Chart Number of 90° elbows Type of vent material and hood combinations acceptable to use old hoses. 1. Connect vent to exhaust hood... straightest path possible. Do not use caulking compound to seal exterior wall opening around exhaust hood. 2. Do not use . Remove old rubber washer from inlet hose and replace with 4" (102 mm) clamp. Dupont De Nemours and Company. To determine maximum exhaust length, add one 90...
... (14.6 m) 2 Rigid metal 44 ft. (13.4 m) 38 ft. (11.6 m) 3 Rigid metal 35 ft. (10.7 m) 29 ft. (8.8 m) 4 Rigid metal 27 ft. (8.2 m) 21 ft. (6.4 m) Maytag Vent System Chart Number of 90° elbows Type of vent material and hood combinations acceptable to use old hoses. 1. Connect vent to exhaust hood... straightest path possible. Do not use caulking compound to seal exterior wall opening around exhaust hood. 2. Do not use . Remove old rubber washer from inlet hose and replace with 4" (102 mm) clamp. Dupont De Nemours and Company. To determine maximum exhaust length, add one 90...
Installation Guide
Page 13
... two-thirds turn. NOTE: Do not overtighten. Using pliers, tighten the couplings an additional two-thirds turn . Check for leaks One end of "Y" connector. Attach washer cold inlet hose to the coupling can result. 4. Screw on coupling by hand until it is seated on fill valve connector. A Fig. Damage to the...
... two-thirds turn. NOTE: Do not overtighten. Using pliers, tighten the couplings an additional two-thirds turn . Check for leaks One end of "Y" connector. Attach washer cold inlet hose to the coupling can result. 4. Screw on coupling by hand until it is seated on fill valve connector. A Fig. Damage to the...