Owners Manual
Page 15
... charging process. ˙ Electrolyte fluid can be used only for charging 12 volt batteries. GB (c) If the engine dose not start by Makita factory or authorized service center. (d) Turn on battery. ˙ Both AC and DC output can burn eyes and clothing. GB Remove oil... 4-t) The DC terminal is defective. G1100(US)_GU1835 2004.2.6 1:04 PM ページ9 WARNING ˙ Be sure to ground the generator if the connected electrical device is within rated output of the generator. Be extremely careful to 12V-8.3A (100W) of carburetor. If injured, wash the affected area ...
... charging process. ˙ Electrolyte fluid can be used only for charging 12 volt batteries. GB (c) If the engine dose not start by Makita factory or authorized service center. (d) Turn on battery. ˙ Both AC and DC output can burn eyes and clothing. GB Remove oil... 4-t) The DC terminal is defective. G1100(US)_GU1835 2004.2.6 1:04 PM ページ9 WARNING ˙ Be sure to ground the generator if the connected electrical device is within rated output of the generator. Be extremely careful to 12V-8.3A (100W) of carburetor. If injured, wash the affected area ...
Owners Manual
Page 18
G1100(US)_GU1835 2004.2.6 1:04 PM ページ12 8. Should the generator be shortened depending on the contamination of oil, clogging of filter elements, wear of parts, and so on the normal generator operation. Check the table below for damage ... 12 The emission control system consists of the following service items: Safe surroundings US Leakage of your generator. DAILY INSPECTION Before running the generator, check the following parts : (1) Carburetor and internal parts (5) Spark plug (2) Cold start enrichment system, (6) Magneto or electronic ignition if ...
G1100(US)_GU1835 2004.2.6 1:04 PM ページ12 8. Should the generator be shortened depending on the contamination of oil, clogging of filter elements, wear of parts, and so on the normal generator operation. Check the table below for damage ... 12 The emission control system consists of the following service items: Safe surroundings US Leakage of your generator. DAILY INSPECTION Before running the generator, check the following parts : (1) Carburetor and internal parts (5) Spark plug (2) Cold start enrichment system, (6) Magneto or electronic ignition if ...
Owners Manual
Page 19
... please refer to the SERVICE MANUAL or consult your nearest Makita service dealer. 13 Initial oil change oil every hundred (...CYLINDER HEAD (*Note 2) CHECK AND ADJUST VALVE CLEARANCE (*Note 2) CLEAN AND ADJUST CARBURETOR (*Note 2) CLEAN AND REPLACE CARBON BRUSHES REPLACE FUEL LINES OVERHAUL ENGINE (*Note 2) ...Daily) ROTOR ˔ STATOR ˔ REPLACE ENGINE MOUNT ˔ *Note: 1. G1100(US)_GU1835 2004.2.6 1:04 PM ページ13 Periodic Maintenance Schedule table ...500 hours Every 1000 hours CLEAN GENERATOR AND CHECK BOLT AND NUTS ˔ (Daily) CHECK AND...
... please refer to the SERVICE MANUAL or consult your nearest Makita service dealer. 13 Initial oil change oil every hundred (...CYLINDER HEAD (*Note 2) CHECK AND ADJUST VALVE CLEARANCE (*Note 2) CLEAN AND ADJUST CARBURETOR (*Note 2) CLEAN AND REPLACE CARBON BRUSHES REPLACE FUEL LINES OVERHAUL ENGINE (*Note 2) ...Daily) ROTOR ˔ STATOR ˔ REPLACE ENGINE MOUNT ˔ *Note: 1. G1100(US)_GU1835 2004.2.6 1:04 PM ページ13 Periodic Maintenance Schedule table ...500 hours Every 1000 hours CLEAN GENERATOR AND CHECK BOLT AND NUTS ˔ (Daily) CHECK AND...
Owners Manual
Page 20
...the drain plug and fill the engine with preservative if available. NEVER USE WATER TO CLEAN GENERATOR ! ˙ Pull starter handle until it into the refilling port. (See Fig. 6-q) ˙ Remove the drain screw of the carburetor. (See Fig. 6-w) q DRAIN SCREW ˙ Change engine oil. ˙ Check...an air cleaner in the fuel tank will result and its contact pressure with the slip ring changes and causes a roughened surface on page 6. G1100(US)_GU1835 2004.2.6 1:04 PM ページ14 9. Spark plug BMR4A (NGK) 14 5. GB Dirt induced through improperly installed, ...
...the drain plug and fill the engine with preservative if available. NEVER USE WATER TO CLEAN GENERATOR ! ˙ Pull starter handle until it into the refilling port. (See Fig. 6-q) ˙ Remove the drain screw of the carburetor. (See Fig. 6-w) q DRAIN SCREW ˙ Change engine oil. ˙ Check...an air cleaner in the fuel tank will result and its contact pressure with the slip ring changes and causes a roughened surface on page 6. G1100(US)_GU1835 2004.2.6 1:04 PM ページ14 9. Spark plug BMR4A (NGK) 14 5. GB Dirt induced through improperly installed, ...