Owners Manual
Page 2
... listed under this engine. GB (1) Fuel Metering System GB (i) Carburetor and internal parts (and/or pressure regulator or fuel injection system).... REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY REPAIR ESTABLISHMENT OR INDIVIDUAL; G1100(US)_GU1835 2004.2.6 1:04 PM ページ02 FEDERAL EMISSIONS COMPONENT DEFECT WARRANTY EMISSIONS ... presenting your sales receipts indicating date of the engine. Inc., La Mirada, California, (herein "MAKITA") warrant(s) to the initial retail purchaser and each subsequent owner of time and furnish you should ...
... listed under this engine. GB (1) Fuel Metering System GB (i) Carburetor and internal parts (and/or pressure regulator or fuel injection system).... REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY REPAIR ESTABLISHMENT OR INDIVIDUAL; G1100(US)_GU1835 2004.2.6 1:04 PM ページ02 FEDERAL EMISSIONS COMPONENT DEFECT WARRANTY EMISSIONS ... presenting your sales receipts indicating date of the engine. Inc., La Mirada, California, (herein "MAKITA") warrant(s) to the initial retail purchaser and each subsequent owner of time and furnish you should ...
Owners Manual
Page 4
...part will GB be performed at no charge for any emission-related part on your engine is performed at an authorized warranty station. G1100(US)_GU1835 2004.2.6 1:04 PM ページ04 CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT (This warranty does not apply in any ...effect of manufacture so as to conform with those regulations as necessary" shall be warranted for presenting your failure to a MAKITA service center as the carburetor or fuel injection systems, the ignition system and the catalytic converter. This limited warranty also does not apply to any emission...
...part will GB be performed at no charge for any emission-related part on your engine is performed at an authorized warranty station. G1100(US)_GU1835 2004.2.6 1:04 PM ページ04 CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT (This warranty does not apply in any ...effect of manufacture so as to conform with those regulations as necessary" shall be warranted for presenting your failure to a MAKITA service center as the carburetor or fuel injection systems, the ignition system and the catalytic converter. This limited warranty also does not apply to any emission...
Owners Manual
Page 15
... remove OIL SENSOR PROBE when refilling with large quantities of the generator. It provides up to 12V-8.3A (100W) of carburetor. STOPPING THE GENERATOR (a) Turn off . G1100(US)_GU1835 2004.2.6 1:04 PM ページ9 WARNING ˙ Be sure to ground the generator if the connected...terminal is within rated output of water and consult a doctor for charging 12 volt batteries. GB (c) If the engine dose not start by Makita factory or authorized service center. (d) Turn on the opposite side GB of maximum power. Stop the generator immediately, check the appliance and / ...
... remove OIL SENSOR PROBE when refilling with large quantities of the generator. It provides up to 12V-8.3A (100W) of carburetor. STOPPING THE GENERATOR (a) Turn off . G1100(US)_GU1835 2004.2.6 1:04 PM ページ9 WARNING ˙ Be sure to ground the generator if the connected...terminal is within rated output of water and consult a doctor for charging 12 volt batteries. GB (c) If the engine dose not start by Makita factory or authorized service center. (d) Turn on the opposite side GB of maximum power. Stop the generator immediately, check the appliance and / ...
Owners Manual
Page 18
... TO GB CONDUCT THE MAINTENANCE AND ADJUSTMENTS ON THE EMISSIONRELATED PARTS LISTED BELOW TO KEEP THE EMISSION CONTROL GB SYSTEM EFFECTIVE. G1100(US)_GU1835 2004.2.6 1:04 PM ページ12 8. Check the table below for damage GB GB Enough gasoline...element GB GB PERIODIC MAINTENANCE GB Periodic maintenance is based on . 12 DAILY INSPECTION Before running the generator, check the following parts : (1) Carburetor and internal parts (5) Spark plug (2) Cold start enrichment system, (6) Magneto or electronic ignition if applicable system (3) Intake manifold, if applicable ...
... TO GB CONDUCT THE MAINTENANCE AND ADJUSTMENTS ON THE EMISSIONRELATED PARTS LISTED BELOW TO KEEP THE EMISSION CONTROL GB SYSTEM EFFECTIVE. G1100(US)_GU1835 2004.2.6 1:04 PM ページ12 8. Check the table below for damage GB GB Enough gasoline...element GB GB PERIODIC MAINTENANCE GB Periodic maintenance is based on . 12 DAILY INSPECTION Before running the generator, check the following parts : (1) Carburetor and internal parts (5) Spark plug (2) Cold start enrichment system, (6) Magneto or electronic ignition if applicable system (3) Intake manifold, if applicable ...
Owners Manual
Page 19
... REMOVE CARBON FROM CYLINDER HEAD (*Note 2) CHECK AND ADJUST VALVE CLEARANCE (*Note 2) CLEAN AND ADJUST CARBURETOR (*Note 2) CLEAN AND REPLACE CARBON BRUSHES REPLACE FUEL LINES OVERHAUL ENGINE (*Note 2) ˔ ˔...SWITCH ˔ (Daily) ROTOR ˔ STATOR ˔ REPLACE ENGINE MOUNT ˔ *Note: 1. G1100(US)_GU1835 2004.2.6 1:04 PM ページ13 Periodic Maintenance Schedule table Maintenance Items Every 8...; (Refill daily up to the SERVICE MANUAL or consult your nearest Makita service dealer. 13 Thereafter change should be performed after first twenty (20) ...
... REMOVE CARBON FROM CYLINDER HEAD (*Note 2) CHECK AND ADJUST VALVE CLEARANCE (*Note 2) CLEAN AND ADJUST CARBURETOR (*Note 2) CLEAN AND REPLACE CARBON BRUSHES REPLACE FUEL LINES OVERHAUL ENGINE (*Note 2) ˔ ˔...SWITCH ˔ (Daily) ROTOR ˔ STATOR ˔ REPLACE ENGINE MOUNT ˔ *Note: 1. G1100(US)_GU1835 2004.2.6 1:04 PM ページ13 Periodic Maintenance Schedule table Maintenance Items Every 8...; (Refill daily up to the SERVICE MANUAL or consult your nearest Makita service dealer. 13 Thereafter change should be performed after first twenty (20) ...
Owners Manual
Page 20
Clean paper element every 50 hours of the carburetor. (See Fig. 6-w) q DRAIN SCREW ˙ Change engine oil. ˙ Check for periods of the engine oil is not sufficient, the GB engine damage will result ... GB operation, and replace element every 200 hours or once a year. (c) Urethane form : Wash the element with oiled cloth. Keep the GB element always clean. G1100(US)_GU1835 2004.2.6 1:04 PM ページ14 9. Never use the hand pomp and set it reaches the upper level on the oil filler...
Clean paper element every 50 hours of the carburetor. (See Fig. 6-w) q DRAIN SCREW ˙ Change engine oil. ˙ Check for periods of the engine oil is not sufficient, the GB engine damage will result ... GB operation, and replace element every 200 hours or once a year. (c) Urethane form : Wash the element with oiled cloth. Keep the GB element always clean. G1100(US)_GU1835 2004.2.6 1:04 PM ページ14 9. Never use the hand pomp and set it reaches the upper level on the oil filler...