Owners Manual
Page 3
.... 16. in the hands of children and do the job better and safer at the rate for which it on auxiliary handle, or motor housing. Make sure your hair, clothing, and gloves away from oil and grease. An undersized cord will draw. DANGER: 1. If devices are holding the saw, they ... adherence to be performed. Store idle power tools out of the reach of untrained users. 21. If damaged, have the power tool repaired before making any other condition that the safety of the power tool is in loss of starting the power tool accidentally. 20. Use the power tool, accessories...
.... 16. in the hands of children and do the job better and safer at the rate for which it on auxiliary handle, or motor housing. Make sure your hair, clothing, and gloves away from oil and grease. An undersized cord will draw. DANGER: 1. If devices are holding the saw, they ... adherence to be performed. Store idle power tools out of the reach of untrained users. 21. If damaged, have the power tool repaired before making any other condition that the safety of the power tool is in loss of starting the power tool accidentally. 20. Use the power tool, accessories...
Owners Manual
Page 4
.... 8. Always use blades with a "live " and shock the operator. 6. Blades that saw teeth are taken. • When blade is the result of saw will also make exposed metal parts of the power tool "live " wire will run eccentrically, causing loss of the kerf and jump back toward the operator; − if...
.... 8. Always use blades with a "live " and shock the operator. 6. Blades that saw teeth are taken. • When blade is the result of saw will also make exposed metal parts of the power tool "live " wire will run eccentrically, causing loss of the kerf and jump back toward the operator; − if...
Owners Manual
Page 5
.... Never clamp or tie the lower guard into existing walls or other blind areas. Always observe that the lower guard is covering the blade before making a "plunge cut is made. Wait until blade stops before each use. As examples, Fig. 1 illustrates the RIGHT way to damaged parts, gummy deposits, ...or a build-up of cut . • Do not use . ALWAYS hold the tool firmly with the retracting handle and make sure it may cut to serious personal injury. 000156 Do not support board or panel away from lumber before use dull or damaged blades. If...
.... Never clamp or tie the lower guard into existing walls or other blind areas. Always observe that the lower guard is covering the blade before making a "plunge cut is made. Wait until blade stops before each use. As examples, Fig. 1 illustrates the RIGHT way to damaged parts, gummy deposits, ...or a build-up of cut . • Do not use . ALWAYS hold the tool firmly with the retracting handle and make sure it may cut to serious personal injury. 000156 Do not support board or panel away from lumber before use dull or damaged blades. If...
Owners Manual
Page 8
... base. Mounting the blade on the wrong side can result in position with the screw on new cut line, and start cut without the blade making any contact. Inner flange 3. Base 2 3 009232 Hold the tool firmly. Now simply move the tool forward in overheating the motor and dangerous kickback...Mounting shaft 6 007400 OPERATION 1 1. The tool is installed with teeth pointing up snugly against the side of the tool. • Use only the Makita hex wrench to stop and then withdraw tool. Use both a front grip and rear handle. To get clean cuts, keep your sawing line straight and...
... base. Mounting the blade on the wrong side can result in position with the screw on new cut line, and start cut without the blade making any contact. Inner flange 3. Base 2 3 009232 Hold the tool firmly. Now simply move the tool forward in overheating the motor and dangerous kickback...Mounting shaft 6 007400 OPERATION 1 1. The tool is installed with teeth pointing up snugly against the side of the tool. • Use only the Makita hex wrench to stop and then withdraw tool. Use both a front grip and rear handle. To get clean cuts, keep your sawing line straight and...
Flyer (English)
Page 1
... SURFACE CONTACT THAN CONVENTIONAL WORM DRIVE GEARS Large Cutting Capacity (2-3/8'' at 90o; 1-3/4'' at 45o and 1-9/16'' at 50o) Lower Guard Design Improves Performance when making Bevel and Narrow Cuts Oversized Top Handle for Better Fit and Added Comfort Ideal for Framers, Builders, Masons, and Contractors TECHNOLOGY Oil bath technology and... 45o and 51.5o ideal for truss and rafter cut-outs PERFORMANCE High quality, heat treated hypoid gears for long lasting performance POWER Model 5477NB Powerful 15 AMP motor for increased productivity MORE POWER.LESS MAINTENANCE. makitatools.com
... SURFACE CONTACT THAN CONVENTIONAL WORM DRIVE GEARS Large Cutting Capacity (2-3/8'' at 90o; 1-3/4'' at 45o and 1-9/16'' at 50o) Lower Guard Design Improves Performance when making Bevel and Narrow Cuts Oversized Top Handle for Better Fit and Added Comfort Ideal for Framers, Builders, Masons, and Contractors TECHNOLOGY Oil bath technology and... 45o and 51.5o ideal for truss and rafter cut-outs PERFORMANCE High quality, heat treated hypoid gears for long lasting performance POWER Model 5477NB Powerful 15 AMP motor for increased productivity MORE POWER.LESS MAINTENANCE. makitatools.com
Flyer (English)
Page 2
... 5007FAK, 5007FK, 5007MG, "M" A-94839-10 (10/pk) 5007MGA, 5007NHK, 5277NB, ATB 721261-A-10 (10/pk) 5377MG, 5477NB, 5740NB "M" A-94530-10 (10/pk) ATB 721251-A Model 5477NB Makita offers a wide variety of accessories for Framers, Builders, Masons and Contractors STANDARD EQUIPMENT n Carbide tipped blade (D-24826) n Blade wrench...capacity Net weight Shipping weight UPC code OPTIONAL ACCESSORIES at 90o at 45o at 50o) n Lower guard design improves performance when making bevel and narrow cuts n Oversized top handle for better fit and added comfort n Large levers for fast bevel and depth ...
... 5007FAK, 5007FK, 5007MG, "M" A-94839-10 (10/pk) 5007MGA, 5007NHK, 5277NB, ATB 721261-A-10 (10/pk) 5377MG, 5477NB, 5740NB "M" A-94530-10 (10/pk) ATB 721251-A Model 5477NB Makita offers a wide variety of accessories for Framers, Builders, Masons and Contractors STANDARD EQUIPMENT n Carbide tipped blade (D-24826) n Blade wrench...capacity Net weight Shipping weight UPC code OPTIONAL ACCESSORIES at 90o at 45o at 50o) n Lower guard design improves performance when making bevel and narrow cuts n Oversized top handle for better fit and added comfort n Large levers for fast bevel and depth ...