Use & Care Guide
Page 20
...176;F to 71.6°F (20°C to perform as specified in your water supply. Prices are not necessarily in NSF/ANSI Standards 42 and 53. If the filter indicator light is red, it is recommended that is essential that operational, maintenance, and filter replacement requirements ...176; - 100°F (0.6° - 37.8°C) 0.85 gpm (3.2 Lpm) @ 60 psi ■ These contaminants are subject to NSF/ANSI Standards 42 and 53 for the reduction of Mercury, Benzene, Toxaphene, O-dichlorobenzene, and Carbofuran. When the filter indicator reads 0%, it is recommended that you replace the...
...176;F to 71.6°F (20°C to perform as specified in your water supply. Prices are not necessarily in NSF/ANSI Standards 42 and 53. If the filter indicator light is red, it is recommended that is essential that operational, maintenance, and filter replacement requirements ...176; - 100°F (0.6° - 37.8°C) 0.85 gpm (3.2 Lpm) @ 60 psi ■ These contaminants are subject to NSF/ANSI Standards 42 and 53 for the reduction of Mercury, Benzene, Toxaphene, O-dichlorobenzene, and Carbofuran. When the filter indicator reads 0%, it is recommended that you replace the...
Use & Care Guide
Page 21
...96.34 99.63 93.33 74.00 Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Prices are not necessarily in NSF/ANSI 42/53. When the filter indicator reads 0%, it is microbiologically unsafe or of $39.99 U.S.A./$49.99 Canada. While testing was reduced to a ...- 827 kPa) 33° - 100°F (0.6° - 37.8°C) 0.5 gpm (1.9 Lpm) @ 60 psi ■ These contaminants are subject to NSF/ANSI 42/53 for the Manufacturer's name, address and telephone number. ■ Refer to check the status of Mercury, Benzene, Toxaphene, O-dichlorobenzene, and Carbofuran. Pressure = 60 psig...
...96.34 99.63 93.33 74.00 Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Prices are not necessarily in NSF/ANSI 42/53. When the filter indicator reads 0%, it is microbiologically unsafe or of $39.99 U.S.A./$49.99 Canada. While testing was reduced to a ...- 827 kPa) 33° - 100°F (0.6° - 37.8°C) 0.5 gpm (1.9 Lpm) @ 60 psi ■ These contaminants are subject to NSF/ANSI 42/53 for the Manufacturer's name, address and telephone number. ■ Refer to check the status of Mercury, Benzene, Toxaphene, O-dichlorobenzene, and Carbofuran. Pressure = 60 psig...
Dimension Guide
Page 1
...KSSO42QT KSSO48FT KSSO48QT KSSP36QT KSSP42QT KSSP48QT KSSS36FT KSSS42FT KSSS48FT KSSS36QT KSSS42QT KSSS48QT KSSC42QV KSSC48QV Electrical: A 115-volt, 60-Hz, AC-only 15- If the water shutoff valve is not in the back wall behind the refrigerator, it must be provided. Instructions packed with the leveling legs extended ...(3.2 cm) below 55°F (13°C). PRODUCT DIMENSIONS A TOP VIEW 25³⁄₈" (64.5 cm) Model Width A 36 35" (88.9 cm) 42 41" (104.1 cm) 48 47" (119.4 cm) 25³⁄₈" (64.5 cm) 23¹⁄₂" (59.7 cm) ■ Height dimensions...
...KSSO42QT KSSO48FT KSSO48QT KSSP36QT KSSP42QT KSSP48QT KSSS36FT KSSS42FT KSSS48FT KSSS36QT KSSS42QT KSSS48QT KSSC42QV KSSC48QV Electrical: A 115-volt, 60-Hz, AC-only 15- If the water shutoff valve is not in the back wall behind the refrigerator, it must be provided. Instructions packed with the leveling legs extended ...(3.2 cm) below 55°F (13°C). PRODUCT DIMENSIONS A TOP VIEW 25³⁄₈" (64.5 cm) Model Width A 36 35" (88.9 cm) 42 41" (104.1 cm) 48 47" (119.4 cm) 25³⁄₈" (64.5 cm) 23¹⁄₂" (59.7 cm) ■ Height dimensions...
Dimension Guide
Page 2
... must be at same level as shown above) 36 35¹⁄₂" (90.2 cm) to 35³⁄₄" (90.8 cm) 42 41¹⁄₂" (105.4 cm) to 41³⁄₄" (106.1 cm) 48 47¹⁄₂" (120.7 cm) to... a corner wall. ® Side by Side Built-In Refrigerator PRODUCT MODEL NUMBERS KSSC36FT KSSC36QT KSSC42FT KSSC42QT KSSC48FT KSSC48QT KSSO36FT KSSO36QT KSSO42FT KSSO42QT KSSO48FT KSSO48QT KSSP36QT KSSP42QT KSSP48QT KSSS36FT KSSS42FT KSSS48FT KSSS36QT KSSS42QT KSSS48QT KSSC42QV KSSC48QV CABINET OPENING DIMENSIONS 80" - 90" (203-229 cm) 4" (10.2 cm) 83...
... must be at same level as shown above) 36 35¹⁄₂" (90.2 cm) to 35³⁄₄" (90.8 cm) 42 41¹⁄₂" (105.4 cm) to 41³⁄₄" (106.1 cm) 48 47¹⁄₂" (120.7 cm) to... a corner wall. ® Side by Side Built-In Refrigerator PRODUCT MODEL NUMBERS KSSC36FT KSSC36QT KSSC42FT KSSC42QT KSSC48FT KSSC48QT KSSO36FT KSSO36QT KSSO42FT KSSO42QT KSSO48FT KSSO48QT KSSP36QT KSSP42QT KSSP48QT KSSS36FT KSSS42FT KSSS48FT KSSS36QT KSSS42QT KSSS48QT KSSC42QV KSSC48QV CABINET OPENING DIMENSIONS 80" - 90" (203-229 cm) 4" (10.2 cm) 83...
Installation Guide
Page 7
..., resulting in the cabinets, the plumbing for more information. ■ The water shutoff should be placed within 4" (10.2 cm) of cooling. Before you move your refrigerator be at same level as the room. Then reset the control to the desired setting. 1" 6" (2.54 cm) (15.2 cm) 24" (60.96 cm) min. 6"... (15.2 cm) Model Width A (as shown above) 36 35¹⁄₂" (90.2 cm) to 35³⁄₄" (90.8 cm) 42 41¹⁄₂" (105.4 cm) to 41³⁄₄" (106.1 cm) 48 47¹⁄₂" (120.7 cm) to follow these instructions can...
..., resulting in the cabinets, the plumbing for more information. ■ The water shutoff should be placed within 4" (10.2 cm) of cooling. Before you move your refrigerator be at same level as the room. Then reset the control to the desired setting. 1" 6" (2.54 cm) (15.2 cm) 24" (60.96 cm) min. 6"... (15.2 cm) Model Width A (as shown above) 36 35¹⁄₂" (90.2 cm) to 35³⁄₄" (90.8 cm) 42 41¹⁄₂" (105.4 cm) to 41³⁄₄" (106.1 cm) 48 47¹⁄₂" (120.7 cm) to follow these instructions can...
Installation Guide
Page 8
...be reduced. The access hole through the floor. On the floor, the hole should be a minimum of the refrigerator or some other easily accessible area. Before purchasing, make sure a saddle-type valve complies with a reverse osmosis system...pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to refill after heavy usage. ■ If your local plumbing codes. Replace the filter if necessary. ...more easily. A Model Tipping Radius A 36 90¹⁄₂" (229.9 cm) 42 93" (236.2 cm) 48 96" (243.8 cm) 8
...be reduced. The access hole through the floor. On the floor, the hole should be a minimum of the refrigerator or some other easily accessible area. Before purchasing, make sure a saddle-type valve complies with a reverse osmosis system...pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to refill after heavy usage. ■ If your local plumbing codes. Replace the filter if necessary. ...more easily. A Model Tipping Radius A 36 90¹⁄₂" (229.9 cm) 42 93" (236.2 cm) 48 96" (243.8 cm) 8
Installation Guide
Page 9
Model Width A 36 35" (88.9 cm) 42 41" (104.1 cm) 48 47" (119.4 cm) 9 Product Dimensions Side View Front View ■ The depth from the front of the top grille to the back of the refrigerator cabinet is 25³⁄₈" (64.5 cm). ■ The power cord is 84" (213 cm)... long. ■ The water line attached to the back of the refrigerator is 5 ft (1.5 m) long. ■ Height dimensions are shown with leveling legs extended ¹⁄₈" (3 mm) below the rollers. ■ Width dimensions were ...
Model Width A 36 35" (88.9 cm) 42 41" (104.1 cm) 48 47" (119.4 cm) 9 Product Dimensions Side View Front View ■ The depth from the front of the top grille to the back of the refrigerator cabinet is 25³⁄₈" (64.5 cm). ■ The power cord is 84" (213 cm)... long. ■ The water line attached to the back of the refrigerator is 5 ft (1.5 m) long. ■ Height dimensions are shown with leveling legs extended ¹⁄₈" (3 mm) below the rollers. ■ Width dimensions were ...
Installation Guide
Page 10
Door Swing Dimensions The location must permit both doors to open to a minimum of the refrigerator and a corner wall. 42" (106.7 cm) Models NOTE: More clearance may be required if you are using overlay panels, custom handles, or extended handles on a Classic model. 12⁵...;₈" (111.4 cm) 90˚ 110˚ 130˚ 90˚ 110˚ 130˚ 41¹⁄₂" (105.4 cm) 16⁷⁄₈" (42.9 cm) 47⁷⁄₈" (121.6 cm) 44" (111.8 cm) 19¹⁄₄" (48.9 cm) 51³⁄₈" (130.5 cm) 10 Allow 4¹...
Door Swing Dimensions The location must permit both doors to open to a minimum of the refrigerator and a corner wall. 42" (106.7 cm) Models NOTE: More clearance may be required if you are using overlay panels, custom handles, or extended handles on a Classic model. 12⁵...;₈" (111.4 cm) 90˚ 110˚ 130˚ 90˚ 110˚ 130˚ 41¹⁄₂" (105.4 cm) 16⁷⁄₈" (42.9 cm) 47⁷⁄₈" (121.6 cm) 44" (111.8 cm) 19¹⁄₄" (48.9 cm) 51³⁄₈" (130.5 cm) 10 Allow 4¹...
Installation Guide
Page 13
... some cases, your refrigerator into the overall kitchen décor, and to 19.05 mm) Backer Panel 1/4" 1/8" (6.35 mm) (3.18 mm) 1" minimum (2.54 cm) Door/Grille Trim Offset Dimension Model 36 42 48 A 14³/₄" (37.47 cm) 17¹/₄" (43.82 cm) 19³/₄" (50....;⁄₄" (36.2 cm) 10⁷⁄₈" (27.6 cm) 72¹⁄₄" Freezer (183.5 cm) Door Panel (Non-Dispenser) Refrigerator Door Panel Overlay Panel Spacer Panel Spacer Panel 1/8" (3.18 mm) Overlay Panel 33⁷⁄₈" (86.0 cm) Dispenser cutout is centered left-to-right...
... some cases, your refrigerator into the overall kitchen décor, and to 19.05 mm) Backer Panel 1/4" 1/8" (6.35 mm) (3.18 mm) 1" minimum (2.54 cm) Door/Grille Trim Offset Dimension Model 36 42 48 A 14³/₄" (37.47 cm) 17¹/₄" (43.82 cm) 19³/₄" (50....;⁄₄" (36.2 cm) 10⁷⁄₈" (27.6 cm) 72¹⁄₄" Freezer (183.5 cm) Door Panel (Non-Dispenser) Refrigerator Door Panel Overlay Panel Spacer Panel Spacer Panel 1/8" (3.18 mm) Overlay Panel 33⁷⁄₈" (86.0 cm) Dispenser cutout is centered left-to-right...
Installation Guide
Page 14
... cm) A A B Bottom Offset ¹⁄₈" (3.2 mm) Bottom Offset ¹⁄₈" (3.2 mm) Model 36 42 48 D 14¹/₄" (36.20 cm) 16³/₄" (42.55 cm) 19¹/₄" (48.90 cm) E 19¹/₄" (48.90 cm) 22³/₄" (57.79...Dispenser Frame (dispenser models only) The dispenser frame attaches to the panel and replace the screws. Remove the four screws attaching the frame. 2. Refrigerator door C. Backer Panels NOTES: ■ Dashed lines represent placement of backer panels on overlay panels. ■ Illustration shows backer panels placed on...
... cm) A A B Bottom Offset ¹⁄₈" (3.2 mm) Bottom Offset ¹⁄₈" (3.2 mm) Model 36 42 48 D 14¹/₄" (36.20 cm) 16³/₄" (42.55 cm) 19¹/₄" (48.90 cm) E 19¹/₄" (48.90 cm) 22³/₄" (57.79...Dispenser Frame (dispenser models only) The dispenser frame attaches to the panel and replace the screws. Remove the four screws attaching the frame. 2. Refrigerator door C. Backer Panels NOTES: ■ Dashed lines represent placement of backer panels on overlay panels. ■ Illustration shows backer panels placed on...
Installation Guide
Page 15
...or stainless steel door and top grille panels are available. NOTE: Panel kits are available through your KitchenAid dealer or by -side and bottomfreezer refrigerators that require overlay panels. Architect® Series Handles PART NO. Follow the kit instructions for factory... Round end arc handle (4396779) with stainless steel clamshell standoffs (4396775) C. Door Panel Part Numbers for Non-dispenser Models Color 36 42 48 White #2325136 #2325137 #2325138 Black #2325139 #2325140 #2325141 Stainless Steel #2325142 #2325143 #2325144 Door Panel Part Numbers for each ...
...or stainless steel door and top grille panels are available. NOTE: Panel kits are available through your KitchenAid dealer or by -side and bottomfreezer refrigerators that require overlay panels. Architect® Series Handles PART NO. Follow the kit instructions for factory... Round end arc handle (4396779) with stainless steel clamshell standoffs (4396775) C. Door Panel Part Numbers for Non-dispenser Models Color 36 42 48 White #2325136 #2325137 #2325138 Black #2325139 #2325140 #2325141 Stainless Steel #2325142 #2325143 #2325144 Door Panel Part Numbers for each ...
Installation Guide
Page 16
... wood panel ¹⁄₂" (1.27 cm) Model A B 36 14¹⁄₄" (36.2 cm) 19¹⁄₄" (48.9 cm) 42 16³⁄₄" (42.6 cm) 22³⁄₄" (57.8 cm) 48 19¹⁄₄" (48.9 cm) 26¹⁄₄" (66.7 cm) NOTES: ... cm) Side Offsets 1.11 cm) Door Panels for Non-dispenser Models The freezer panel should be 3¹⁄₄" (8.25 cm) to your refrigerator. The refrigerator panel should be 1.1 cm). IMPORTANT: Panels weighing more than ¹⁄₄" (6.35 mm) thick must be routed. If panels are more ...
... wood panel ¹⁄₂" (1.27 cm) Model A B 36 14¹⁄₄" (36.2 cm) 19¹⁄₄" (48.9 cm) 42 16³⁄₄" (42.6 cm) 22³⁄₄" (57.8 cm) 48 19¹⁄₄" (48.9 cm) 26¹⁄₄" (66.7 cm) NOTES: ... cm) Side Offsets 1.11 cm) Door Panels for Non-dispenser Models The freezer panel should be 3¹⁄₄" (8.25 cm) to your refrigerator. The refrigerator panel should be 1.1 cm). IMPORTANT: Panels weighing more than ¹⁄₄" (6.35 mm) thick must be routed. If panels are more ...
Installation Guide
Page 19
... the side of the top grille. Remove and save the literature package bag taped to move and install refrigerator. See "Tipping Radius" in opening. 3. Model Reduced Tipping Radius 36 88" (223.5 cm) 42 88¹⁄₂" (224.8 cm) 48 89¹⁄₄" (226.7 cm) 1. ...A. Remove the four brackets (two on each cabinet side trim to the refrigerator bottom. Remove the six screws attaching each side) that attach the...
... the side of the top grille. Remove and save the literature package bag taped to move and install refrigerator. See "Tipping Radius" in opening. 3. Model Reduced Tipping Radius 36 88" (223.5 cm) 42 88¹⁄₂" (224.8 cm) 48 89¹⁄₄" (226.7 cm) 1. ...A. Remove the four brackets (two on each cabinet side trim to the refrigerator bottom. Remove the six screws attaching each side) that attach the...