Instruction Manual
Page 2
...your speakers from the battery. Wiring • Take the battery wire for bridged connections). They can occur. To prevent battery rise When the unit is running, connect a line noise filter (optional) to each amplifier. If it's connected to the vehicle's wiring harness, it can cause ... replacing a fuse, only use because the surface of greater current-handling capacity than one with a protection function for protecting this unit and your Kenwood dealer. Using a fuse with a 8 mm² (AWG 8) or more than the total maximum current drawn by volatile solvents such as...
...your speakers from the battery. Wiring • Take the battery wire for bridged connections). They can occur. To prevent battery rise When the unit is running, connect a line noise filter (optional) to each amplifier. If it's connected to the vehicle's wiring harness, it can cause ... replacing a fuse, only use because the surface of greater current-handling capacity than one with a protection function for protecting this unit and your Kenwood dealer. Using a fuse with a 8 mm² (AWG 8) or more than the total maximum current drawn by volatile solvents such as...
Instruction Manual
Page 4
... Speaker wire connection Power control wire Terminal cover Battery wire* Protective Fuse* Battery Ground wire* Lead terminal* Right speaker Left speaker ■ Bridged Connections Speaker (Bridged) ■ Remote cable connection (KAC-7252 only) 2CAUTION • Before connecting the remote controller cables, always set the Bass boost level control to appropriate speaker connectors separately.
... Speaker wire connection Power control wire Terminal cover Battery wire* Protective Fuse* Battery Ground wire* Lead terminal* Right speaker Left speaker ■ Bridged Connections Speaker (Bridged) ■ Remote cable connection (KAC-7252 only) 2CAUTION • Before connecting the remote controller cables, always set the Bass boost level control to appropriate speaker connectors separately.
Instruction Manual
Page 5
...used to the maximum power output of the amplifier. • STEREO position: The amplifier can 't find the specified capacity fuse at your store etc., consult your Kenwood dealer. 2 Battery terminal 3 Ground terminal ... terminal The signal that the combined impedance is turned on the right as a high-output monaural amplifier, bridged connections are used . (Make connections to the LEFT channel 9 and the RIGHT channel ·...band of trouble. (See page 2) @ BASS BOOST LEVEL control (KAC-7202 only) Sets the low frequency level to use the unit as a guide. Use the diagram on , the...
...used to the maximum power output of the amplifier. • STEREO position: The amplifier can 't find the specified capacity fuse at your store etc., consult your Kenwood dealer. 2 Battery terminal 3 Ground terminal ... terminal The signal that the combined impedance is turned on the right as a high-output monaural amplifier, bridged connections are used . (Make connections to the LEFT channel 9 and the RIGHT channel ·...band of trouble. (See page 2) @ BASS BOOST LEVEL control (KAC-7202 only) Sets the low frequency level to use the unit as a guide. Use the diagram on , the...
Instruction Manual
Page 6
...f CENTER UNIT ,, ,).%/54 ,, ,).%/54 g Left speaker (High pass) Right speaker (High pass) Subwoofer (L + R) (Bridged) fg f g ■ Tri-mode CENTER UNIT (High pass) Subwoofer (L + R) (Bridged) # , ,, # 6 English Principle of Tri-mode Method of frequency band division using speakers with an impedance of 4 ohms. Prepare ... (µF) and the coil rating should be as close as possible to 5.3 (mH). 2CAUTION • If you wish to bridge-connect a speaker, the speaker impedance must be passed. Failure to which high frequencies will be no less than 4 ohms may ...
...f CENTER UNIT ,, ,).%/54 ,, ,).%/54 g Left speaker (High pass) Right speaker (High pass) Subwoofer (L + R) (Bridged) fg f g ■ Tri-mode CENTER UNIT (High pass) Subwoofer (L + R) (Bridged) # , ,, # 6 English Principle of Tri-mode Method of frequency band division using speakers with an impedance of 4 ohms. Prepare ... (µF) and the coil rating should be as close as possible to 5.3 (mH). 2CAUTION • If you wish to bridge-connect a speaker, the speaker impedance must be passed. Failure to which high frequencies will be no less than 4 ohms may ...
Instruction Manual
Page 7
... KAC-7202 Max Power Output...1000 W 920 W Rated Power Output (+B = 14.4 V) Normal (4 Ω) (20 Hz - 20 kHz, 0.08 % THD)...170 W × 2 150 W × 2 Normal (4 Ω) (DIN : 45324 , +B = 14.4V)...170 W × 2 150 W × 2 Normal (2 Ω) (1 kHz, 0.8 % THD) ...250 W × 2 230 W × 2 Bridged (4 ...) Bass Boost Circuit...0 - +18 dB (variable) 0 - +18 dB (variable) Bass Boost Frequency...40 - 100 Hz (variable) 40 Hz General ...KAC-7252 KAC-7202 Operating Voltage ...14.4 V (11 - 16 V allowable) 14.4 V (11 - 16 V allowable) Current Consumption ...40 A 40 A Installation Size (W...
... KAC-7202 Max Power Output...1000 W 920 W Rated Power Output (+B = 14.4 V) Normal (4 Ω) (20 Hz - 20 kHz, 0.08 % THD)...170 W × 2 150 W × 2 Normal (4 Ω) (DIN : 45324 , +B = 14.4V)...170 W × 2 150 W × 2 Normal (2 Ω) (1 kHz, 0.8 % THD) ...250 W × 2 230 W × 2 Bridged (4 ...) Bass Boost Circuit...0 - +18 dB (variable) 0 - +18 dB (variable) Bass Boost Frequency...40 - 100 Hz (variable) 40 Hz General ...KAC-7252 KAC-7202 Operating Voltage ...14.4 V (11 - 16 V allowable) 14.4 V (11 - 16 V allowable) Current Consumption ...40 A 40 A Installation Size (W...