Owner's Manual (pdf)
Page 1
...power amplifier. KAC-6104D CLASS D MONO POWER AMPLIFIER 3 page 2-9 INSTRUCTION MANUAL AMPLIFICATEUR MONO CLASSE D 3 page 10-17 MODE D'EMPLOI AMPLIFICADOR DE POTENCIA CLASE D MONOFÓNICO 3 página 18-25 MANUAL DE INSTRUCCIONES Take the time to the model and serial numbers whenever you obtain the best performance from your Kenwood... with installation and operation procedures will help you call upon your records Record the serial number, found on the back of the unit, in the spaces designated on the product. Refer to read through this instruction manual. For your Kenwood dealer ...
...power amplifier. KAC-6104D CLASS D MONO POWER AMPLIFIER 3 page 2-9 INSTRUCTION MANUAL AMPLIFICATEUR MONO CLASSE D 3 page 10-17 MODE D'EMPLOI AMPLIFICADOR DE POTENCIA CLASE D MONOFÓNICO 3 página 18-25 MANUAL DE INSTRUCCIONES Take the time to the model and serial numbers whenever you obtain the best performance from your Kenwood... with installation and operation procedures will help you call upon your records Record the serial number, found on the back of the unit, in the spaces designated on the product. Refer to read through this instruction manual. For your Kenwood dealer ...
Owner's Manual (pdf)
Page 2
...• If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your Kenwood dealer. They can cause blown fuses etc. • If a buzzing noise is connected to a 12V DC power supply with a dry silicon cloth or soft cloth. Use it depletes the battery. Do...scratch the surface of the amplifier. For safety's sake, leave the mounting and wiring work to peel off 2tΩhe power and wipe the panel with a negative ground connection. • Do not open the bottom covers of the unit. • Do not install the unit in Watts) of the panel and...
...• If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your Kenwood dealer. They can cause blown fuses etc. • If a buzzing noise is connected to a 12V DC power supply with a dry silicon cloth or soft cloth. Use it depletes the battery. Do...scratch the surface of the amplifier. For safety's sake, leave the mounting and wiring work to peel off 2tΩhe power and wipe the panel with a negative ground connection. • Do not open the bottom covers of the unit. • Do not install the unit in Watts) of the panel and...
Owner's Manual (pdf)
Page 3
... for a Class B digital device, pursuant to the EMC Directive 2004/108/EC Manufacturer: Kenwood Corporation 2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan EU Representative's: Kenwood Electronics Europe BV Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands English This equipment may cause harmful interference to radio communications, if it is not installed and used...
... for a Class B digital device, pursuant to the EMC Directive 2004/108/EC Manufacturer: Kenwood Corporation 2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan EU Representative's: Kenwood Electronics Europe BV Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands English This equipment may cause harmful interference to radio communications, if it is not installed and used...
Owner's Manual (pdf)
Page 4
Installation 198 mm 131 mm 217 mm 230 mm Ø 4.6 Self-tapping screw (ø4 × 16 mm) English Installation board, etc. (thickness : 15 mm or more)
Installation 198 mm 131 mm 217 mm 230 mm Ø 4.6 Self-tapping screw (ø4 × 16 mm) English Installation board, etc. (thickness : 15 mm or more)
Owner's Manual (pdf)
Page 5
... lamps, turn signal lamps and windshield wipers operate normally. Install the amplifier in a place where people, resins, and other damage. • Do not install near the dashboard, rear tray, or air bag safety parts. • The installation to the vehicle should securely fasten the unit to a ...allows heat to easily dissipate. When the protection function is triggered, the Power indicator goes OFF and the amplifier stops operating. • When a speaker wire may cause injury or an accident. • After installing the unit, check to make sure that electrical equipment such as a ...
... lamps, turn signal lamps and windshield wipers operate normally. Install the amplifier in a place where people, resins, and other damage. • Do not install near the dashboard, rear tray, or air bag safety parts. • The installation to the vehicle should securely fasten the unit to a ...allows heat to easily dissipate. When the protection function is triggered, the Power indicator goes OFF and the amplifier stops operating. • When a speaker wire may cause injury or an accident. • After installing the unit, check to make sure that electrical equipment such as a ...
Owner's Manual (pdf)
Page 9
...Watts per channel @ 4 ohms, 1 % THD+N) Signal to Noise Ratio (Reference: 1Watt into 4 ohms) Audio Section Max Power Output Rated Power... Output (+B = 14.4 V) (4 Ω) (20 Hz - 200 Hz, 1.0 % THD) (4 Ω) (DIN45324, +B = 14.4 V) (2 Ω) (100 Hz, 1.0 % THD) Frequency Response (+0, -3 dB) Sensitivity (rated output) (MAX.) (MIN.) Input Impedance Signal to Noise Ratio Low Pass Filter Frequency (-12 dB/oct.) General Operating Voltage Current Consumption Installation...to change without notice. 200 W × 1 75 dBA 600 W 200 W × 1 200 W × 1...
...Watts per channel @ 4 ohms, 1 % THD+N) Signal to Noise Ratio (Reference: 1Watt into 4 ohms) Audio Section Max Power Output Rated Power... Output (+B = 14.4 V) (4 Ω) (20 Hz - 200 Hz, 1.0 % THD) (4 Ω) (DIN45324, +B = 14.4 V) (2 Ω) (100 Hz, 1.0 % THD) Frequency Response (+0, -3 dB) Sensitivity (rated output) (MAX.) (MIN.) Input Impedance Signal to Noise Ratio Low Pass Filter Frequency (-12 dB/oct.) General Operating Voltage Current Consumption Installation...to change without notice. 200 W × 1 75 dBA 600 W 200 W × 1 200 W × 1...