Owner's Manual (pdf)
Page 2
... splashing. • When replacing a fuse, only use a new one power amplifier are going to be emitted as well as damage. • Use speakers...when the engine is running out When the unit is used in Watts) of the amplifier. CAUTION Do not wipe the panel with a hard cloth or... calculate the combined impedance of the unit becomes hot and may cause your Kenwood dealer. Use it If the front p8aΩnel gets dirty, turn ...install the unit in the power cord near the battery. NOTE 4Ω 4Ω 4Ω 4Ω • If you experience problems during use because the surface ...
... splashing. • When replacing a fuse, only use a new one power amplifier are going to be emitted as well as damage. • Use speakers...when the engine is running out When the unit is used in Watts) of the amplifier. CAUTION Do not wipe the panel with a hard cloth or... calculate the combined impedance of the unit becomes hot and may cause your Kenwood dealer. Use it If the front p8aΩnel gets dirty, turn ...install the unit in the power cord near the battery. NOTE 4Ω 4Ω 4Ω 4Ω • If you experience problems during use because the surface ...
Owner's Manual (pdf)
Page 5
... in a location which it . • Do not mount the unit in the following this unit and your speakers from various accidents or problems that can occur. Protection function The protection function is activated in a place where the ducts of the unit are blocked. Once installed, do...that are sensitive to heat will not come into contact with it will not obstruct driving. When the protection function is triggered, the Power indicator goes OFF and the amplifier stops operating. • When a speaker wire may be short-circuited. • When a speaker output contacts ground. • When...
... in a location which it . • Do not mount the unit in the following this unit and your speakers from various accidents or problems that can occur. Protection function The protection function is activated in a place where the ducts of the unit are blocked. Once installed, do...that are sensitive to heat will not come into contact with it will not obstruct driving. When the protection function is triggered, the Power indicator goes OFF and the amplifier stops operating. • When a speaker wire may be short-circuited. • When a speaker output contacts ground. • When...
Owner's Manual (pdf)
Page 9
...improperly. Set switches properly by referring to . Specifications CEA-2006 RMS Watts per channel @ 4 ohms, 1 % THD+N) Signal to Noise Ratio (Reference: 1Watt into 4 ohms) Audio Section Max Power Output Rated Power Output (+B = 14.4 V) (4 Ω) (20 Hz - 200 Hz...600 W 200 W × 1 200 W × 1 300 W × 1 20 Hz - 200 Hz 0.2 V 5.0 V 10 kΩ 94 dB 50 - 200 Hz (variable) 14.4 V (11 - 16 V allowable) 21 A 198 × 59 × 230 mm 7-13/16 × 2-5/16 × 9-1/16 inch 1.8 kg (4.0 lbs) English Before calling service, first check the following table for possible problems...
...improperly. Set switches properly by referring to . Specifications CEA-2006 RMS Watts per channel @ 4 ohms, 1 % THD+N) Signal to Noise Ratio (Reference: 1Watt into 4 ohms) Audio Section Max Power Output Rated Power Output (+B = 14.4 V) (4 Ω) (20 Hz - 200 Hz...600 W 200 W × 1 200 W × 1 300 W × 1 20 Hz - 200 Hz 0.2 V 5.0 V 10 kΩ 94 dB 50 - 200 Hz (variable) 14.4 V (11 - 16 V allowable) 21 A 198 × 59 × 230 mm 7-13/16 × 2-5/16 × 9-1/16 inch 1.8 kg (4.0 lbs) English Before calling service, first check the following table for possible problems...