Owners Manual
Page 1
...front deck. Remove the three nuts and bolts that protect the mulch kit fastening locations (2). NOTE: Only two hardware sites are sharp. Blades are shown in the illustration. Remove the discharge chute assembly by removing the hardware (1) on the bracket top. P/N 115 247027 R1 08... used. 2. Protect your hands with gloves and/or wrap blades with a heavy cloth when handling. 1. Bolt left hand corner mulch baffle to the underside of the deck baffle weldment as shown in the illustration. 3. INSTALLATION INSTRUCTIONS 60" MULCH KIT - 966 444701 IMPORTANT: BEFORE PROCEEDING, PLACE ...
...front deck. Remove the three nuts and bolts that protect the mulch kit fastening locations (2). NOTE: Only two hardware sites are sharp. Blades are shown in the illustration. Remove the discharge chute assembly by removing the hardware (1) on the bracket top. P/N 115 247027 R1 08... used. 2. Protect your hands with gloves and/or wrap blades with a heavy cloth when handling. 1. Bolt left hand corner mulch baffle to the underside of the deck baffle weldment as shown in the illustration. 3. INSTALLATION INSTRUCTIONS 60" MULCH KIT - 966 444701 IMPORTANT: BEFORE PROCEEDING, PLACE ...
Owners Manual
Page 3
... be cut in one pass should be cleaned out often to be finely mulched. • Engine RPM should be set at maximum. • Blades must be kept sharp. • The underside of deck should not exceed 1/3 of the total grass height. Example: If grass height is tight.... 10. Remove blocks and return the mower to 90 ft./lbs.). 8. INSTALLATION INSTRUCTIONS 7. Install the kit mulching blades using the existing blade bolt (torque to its normal position. Mulching Guidelines To ensure acceptable mulching performance: • The length of all hardware is 3", the ...
... be cut in one pass should be cleaned out often to be finely mulched. • Engine RPM should be set at maximum. • Blades must be kept sharp. • The underside of deck should not exceed 1/3 of the total grass height. Example: If grass height is tight.... 10. Remove blocks and return the mower to 90 ft./lbs.). 8. INSTALLATION INSTRUCTIONS 7. Install the kit mulching blades using the existing blade bolt (torque to its normal position. Mulching Guidelines To ensure acceptable mulching performance: • The length of all hardware is 3", the ...
Installation Instructions
Page 3
... the rear. If tires are inflated to the opposite side; Four bolts control the height and pitch of your hands with gloves and/or wrap blades with the deck in a base measurement position. The deck should be equal in a side-to leveling the deck. 20. Wear heavy gloves. Measure...Turn both side-to 3/8" higher in the rear than the front measurement. Confirm measurements once again. In the rear, blade tips should be required to -side. In the front, blade tips should be adjusted slightly higher in Maintenance section of the mower deck. NOTE: This will cause an uneven mowing ...
... the rear. If tires are inflated to the opposite side; Four bolts control the height and pitch of your hands with gloves and/or wrap blades with the deck in a base measurement position. The deck should be equal in a side-to leveling the deck. 20. Wear heavy gloves. Measure...Turn both side-to 3/8" higher in the rear than the front measurement. Confirm measurements once again. In the rear, blade tips should be required to -side. In the front, blade tips should be adjusted slightly higher in Maintenance section of the mower deck. NOTE: This will cause an uneven mowing ...
Installation Instructions
Page 7
... 202001....1..... BOLT 5/16-18 x 1 RD HD 55.. 525 836001....3..... DECAL, NO STEP 60.. 539 113224....1..... DECAL, CPSC 62.. 539 105746....1..... BLADE, HIGH LIFT 21" 574 481301....3..... BLADE, WAVY REV LIFT 21" DECK w/ SAFETY DECALS 2.. 510 437502....1..... ZERK 10.. 521 991101...8 RD HD 21.. 510 022301....3..... GUIDE, BELT 53.. 539 128101....1..... CUP, DEBRIS 57.. 539 130641....3..... OPTIONAL 522 829301....3..... BLADE, GATOR 21" 539 109755....3..... TUBE, ROLLER AXLE LONG ITEM PART NO. QTY. SPRING, TORSION 51.. 574 262201....1..... KEEPER, ...
... 202001....1..... BOLT 5/16-18 x 1 RD HD 55.. 525 836001....3..... DECAL, NO STEP 60.. 539 113224....1..... DECAL, CPSC 62.. 539 105746....1..... BLADE, HIGH LIFT 21" 574 481301....3..... BLADE, WAVY REV LIFT 21" DECK w/ SAFETY DECALS 2.. 510 437502....1..... ZERK 10.. 521 991101...8 RD HD 21.. 510 022301....3..... GUIDE, BELT 53.. 539 128101....1..... CUP, DEBRIS 57.. 539 130641....3..... OPTIONAL 522 829301....3..... BLADE, GATOR 21" 539 109755....3..... TUBE, ROLLER AXLE LONG ITEM PART NO. QTY. SPRING, TORSION 51.. 574 262201....1..... KEEPER, ...
Parts Manual
Page 23
Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 PZ 60, 966 614401-04 Part No. Qty Description 588 12 76-02 1 Deck w/ Safety Decals 539 10 57-11 3 Blade, 21" 510 43 75-02 1 Flow Diverter 574 19 70-02 1 Bracket, Chute Pivot 525 48 58...-01 1 Chute, Discharge 525 48 60-02 1 Support, Chute Bracket 574 16 96-01 5 Roller, Gauge 574 19 64-01...
Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 PZ 60, 966 614401-04 Part No. Qty Description 588 12 76-02 1 Deck w/ Safety Decals 539 10 57-11 3 Blade, 21" 510 43 75-02 1 Flow Diverter 574 19 70-02 1 Bracket, Chute Pivot 525 48 58...-01 1 Chute, Discharge 525 48 60-02 1 Support, Chute Bracket 574 16 96-01 5 Roller, Gauge 574 19 64-01...