Owners Manual
Page 2
... or good artificial light. • Do not operate the machine while under the machine. GENERAL OPERATION • Read, understand, and follow all parts to come to plow leaves or other reproductive harm. Avoid discharging material against a wall or obstruction. Shut off blades, set parking brake, stop ...SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. Too heavy of a load, while on the ground. • Do not mow near rotating parts or under the influence of alcohol or drugs. • Watch for traffic when operating near or crossing roadways. • Use extra care when...
... or good artificial light. • Do not operate the machine while under the machine. GENERAL OPERATION • Read, understand, and follow all parts to come to plow leaves or other reproductive harm. Avoid discharging material against a wall or obstruction. Shut off blades, set parking brake, stop ...SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. Too heavy of a load, while on the ground. • Do not mow near rotating parts or under the influence of alcohol or drugs. • Watch for traffic when operating near or crossing roadways. • Use extra care when...
Owners Manual
Page 3
... or on towed equipment. • On slopes, the weight of the towed equipment may fall off and be seriously injured or interfere with manufacturer's recommended parts, when necessary. • Mower blades are often attracted to cool before refueling. • • Never fuel the machine indoors. • • Never store the machine...
... or on towed equipment. • On slopes, the weight of the towed equipment may fall off and be seriously injured or interfere with manufacturer's recommended parts, when necessary. • Mower blades are often attracted to cool before refueling. • • Never fuel the machine indoors. • • Never store the machine...
Owners Manual
Page 5
Washers (1) Small Retainer Springs Battery (1) Shoulder Bolt (1) Wheel (1) Oil Drain Tube Keys (2) Keys (1) 1-1/4 O.D. Washer (1) 3/8-16 Locknut Slope Sheet (2) Hex Bolts (2) Nut Keps *Installed by Dealer *Brush Guard Kit (1) Quick Connect 5 UNASSEMBLED PARTS Mower Mower Front Wheel (5) 1-3/16 O.D. Washers (2) Rear Lift Link Assemblies (1) Small Retainer Springs (5) Large Retainer Springs (1) Front Lift Link Assembly If Equipped (1) Anti-Sway Bar (1) 3/4 O.D.
Washers (1) Small Retainer Springs Battery (1) Shoulder Bolt (1) Wheel (1) Oil Drain Tube Keys (2) Keys (1) 1-1/4 O.D. Washer (1) 3/8-16 Locknut Slope Sheet (2) Hex Bolts (2) Nut Keps *Installed by Dealer *Brush Guard Kit (1) Quick Connect 5 UNASSEMBLED PARTS Mower Mower Front Wheel (5) 1-3/16 O.D. Washers (2) Rear Lift Link Assemblies (1) Small Retainer Springs (5) Large Retainer Springs (1) Front Lift Link Assembly If Equipped (1) Anti-Sway Bar (1) 3/4 O.D.
Owners Manual
Page 6
... lever (A) and slide seat until a com- TO REMOVE TRACTOR FROM CARTON UNPACK CARTON • Remove all accessible loose parts and parts cartons from the skid. WARNING: Before starting, read, understand and follow . fortable position is located between terminals) charge ...Tire pressure gauge (1) 3/4" wrench Pliers (1) 3/4" socket w/drive ratchet (1) 9/16" wrench Flashlight When right or left unassembled for any additional loose parts or cartons and remove. BEFORE REMOVING TRACTOR FROM SKID TO CHECK BATTERY (See Fig. 1) • Lift hood to ensure proper tightness. Follow the...
... lever (A) and slide seat until a com- TO REMOVE TRACTOR FROM CARTON UNPACK CARTON • Remove all accessible loose parts and parts cartons from the skid. WARNING: Before starting, read, understand and follow . fortable position is located between terminals) charge ...Tire pressure gauge (1) 3/4" wrench Pliers (1) 3/4" socket w/drive ratchet (1) 9/16" wrench Flashlight When right or left unassembled for any additional loose parts or cartons and remove. BEFORE REMOVING TRACTOR FROM SKID TO CHECK BATTERY (See Fig. 1) • Lift hood to ensure proper tightness. Follow the...
Owners Manual
Page 9
... for best cutting results. (Tires must be properly leveled. PLEASE REVIEW THE FOLLOWING CHECKLIST: ✓ All assembly instructions have been completed. ✓ No remaining loose parts in the Operation section of this manual). 9 See "TO LEVEL MOWER HOUSING" in this manual. ✓CHECKLIST BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH...
... for best cutting results. (Tires must be properly leveled. PLEASE REVIEW THE FOLLOWING CHECKLIST: ✓ All assembly instructions have been completed. ✓ No remaining loose parts in the Operation section of this manual). 9 See "TO LEVEL MOWER HOUSING" in this manual. ✓CHECKLIST BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH...
Owners Manual
Page 18
... should NOT shut off the engine. • When the engine is sufficient for proper PSI). • Keep tires free of this manual). If your local parts dealer. CHECK REVERSE OPERATION (ROS) SYSTEM • When the engine is in the Service and Adjustments section of this manual). 18 BLADE REMOVAL (See Fig...
... should NOT shut off the engine. • When the engine is sufficient for proper PSI). • Keep tires free of this manual). If your local parts dealer. CHECK REVERSE OPERATION (ROS) SYSTEM • When the engine is in the Service and Adjustments section of this manual). 18 BLADE REMOVAL (See Fig...
Owners Manual
Page 20
.... CLAMP CLAMP CLEANING • Clean engine, battery, seat, finish, etc. CAUTION: Avoid all times. SPARK PLUGS Replace spark plugs at all pinch points and movable parts (See Fig. 32) CLUTCH/BRAKE PEDAL CLEAN TOP SIDE STEERING PLATE CAUTION: PINCH POINTS STEERING SYSTEM, DASH, FENDER AND MOWER NOT SHOWN Fig. 32 •...
.... CLAMP CLAMP CLEANING • Clean engine, battery, seat, finish, etc. CAUTION: Avoid all times. SPARK PLUGS Replace spark plugs at all pinch points and movable parts (See Fig. 32) CLUTCH/BRAKE PEDAL CLEAN TOP SIDE STEERING PLATE CAUTION: PINCH POINTS STEERING SYSTEM, DASH, FENDER AND MOWER NOT SHOWN Fig. 32 •...
Owners Manual
Page 21
... PORT (See Fig. 33) Your tractor's deck is equipped with bolts and locknuts. 21 Drive the tractor to a level, clear spot on its surface as part of your garden hose. 4. Make sure the attachment clutch control is in mower with a washout port on your lawn, near enough to turn the tractor...
... PORT (See Fig. 33) Your tractor's deck is equipped with bolts and locknuts. 21 Drive the tractor to a level, clear spot on its surface as part of your garden hose. 4. Make sure the attachment clutch control is in mower with a washout port on your lawn, near enough to turn the tractor...
Owners Manual
Page 22
... position. • Place attachment clutch in "DISENGAGED" position. • Turn ignition key to "STOP" and remove key. • Make sure the blades and all moving parts have accumulated around idler pulleys (V) as it cannot come in contact with plug. sion arm (A) from chassis and rear lift link (C) from mower - remove retainer...
... position. • Place attachment clutch in "DISENGAGED" position. • Turn ignition key to "STOP" and remove key. • Make sure the blades and all moving parts have accumulated around idler pulleys (V) as it cannot come in contact with plug. sion arm (A) from chassis and rear lift link (C) from mower - remove retainer...
Owners Manual
Page 24
... (G). 8. Install belt on level surface. Remove mower (See "TO REMOVE MOWER" section in this manual). Remove belt from tractor. Install new belt from your local parts dealer. Be sure belt is set front wheel toe-in all the way down around transmission cooling fan and onto the input pulley (F). Slide belt...
... (G). 8. Install belt on level surface. Remove mower (See "TO REMOVE MOWER" section in this manual). Remove belt from tractor. Install new belt from your local parts dealer. Be sure belt is set front wheel toe-in all the way down around transmission cooling fan and onto the input pulley (F). Slide belt...
Owners Manual
Page 27
... in fuel tank or storage container. ENGINE FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. Always follow the mix ratio found on concrete or damp surfaces....FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. Inspect moving parts for winter storage. BATTERY • Fully charge the battery for storage, do not store battery directly on stabilizer container. ENGINE OIL Drain...
... in fuel tank or storage container. ENGINE FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. Always follow the mix ratio found on concrete or damp surfaces....FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. Inspect moving parts for winter storage. BATTERY • Fully charge the battery for storage, do not store battery directly on stabilizer container. ENGINE OIL Drain...
Owners Manual
Page 28
...fresh gasoline and replace fuel filter. 8. Spark plug wire loose. 10. Clean/replace muffler. 13. Loose/damaged part(s). 1. Replace damaged parts. 28 CORRECTION 1. Replace spark plug. 5. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace ...3. Cutting too much grass/too fast. 1. Throttle in fuel. 9. Check oil level/change spark plug. 7. Check all wiring. 9. Tighten loose part(s). Loose or damaged wiring. 9. Dirty air filter. 2. Brake pedal not depressed. 2. Faulty operator presence switch(es). 1. Clean battery terminals. 6....
...fresh gasoline and replace fuel filter. 8. Spark plug wire loose. 10. Clean/replace muffler. 13. Loose/damaged part(s). 1. Replace damaged parts. 28 CORRECTION 1. Replace spark plug. 5. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace ...3. Cutting too much grass/too fast. 1. Throttle in fuel. 9. Check oil level/change spark plug. 7. Check all wiring. 9. Tighten loose part(s). Loose or damaged wiring. 9. Dirty air filter. 2. Brake pedal not depressed. 2. Faulty operator presence switch(es). 1. Clean battery terminals. 6....
Owners Manual
Page 29
... CAUSE Engine continues to open vent holes. Replace idler pulley. 4. Debris on steering plate (if equipped). 3. Switch is "OFF". 2. Faulty alternator. 1. Place freewheel control in parts manual. 11. Check wiring, switches and connections. Engine speed too slow. 1. Blown fuse. 1. Purge transmission. 5. Clean around mandrels. 1. Loose or damaged wiring. 5. Mower drive belt...
... CAUSE Engine continues to open vent holes. Replace idler pulley. 4. Debris on steering plate (if equipped). 3. Switch is "OFF". 2. Faulty alternator. 1. Place freewheel control in parts manual. 11. Check wiring, switches and connections. Engine speed too slow. 1. Blown fuse. 1. Purge transmission. 5. Clean around mandrels. 1. Loose or damaged wiring. 5. Mower drive belt...
Owners Manual
Page 31
... indicated on Exhibit A, all Engines and Attachments are NOT covered. All such claims must cease using original OEM Husqvarna replacement parts, subject to any warranty obligation of this document. In addition, you require assistance or have any rights thereof... WARRANTY. Should you must be transferred to the limitations and exclusions described below. see Exhibit A). (c) Expendable Parts. Consumer Wheeled Products - Husqvarna does not offer an over-the-counter exchange program. The product should be covered separately by this Limited Warranty...
... indicated on Exhibit A, all Engines and Attachments are NOT covered. All such claims must cease using original OEM Husqvarna replacement parts, subject to any warranty obligation of this document. In addition, you require assistance or have any rights thereof... WARRANTY. Should you must be transferred to the limitations and exclusions described below. see Exhibit A). (c) Expendable Parts. Consumer Wheeled Products - Husqvarna does not offer an over-the-counter exchange program. The product should be covered separately by this Limited Warranty...
Owners Manual
Page 32
... belts, pulleys, spindle housings, bearings, blades, rods, height adjusters, caster/anti scalp wheels are for the deck shell only mechanical components/parts such as prescribed in the operator's manual; (f) Abuse, misuse, neglect, modifications, alterations, normal wear, improper servicing, use of unauthorized ...or oils, failure to improper set up or return of or broken strainers; However, registering your nearest authorized Husqvarna Servicing Dealer, call Husqvarna, at www.usa.husqvarna.com (US & Canada) to help ensure, among other things, that resulting from abuse or neglect of ...
... belts, pulleys, spindle housings, bearings, blades, rods, height adjusters, caster/anti scalp wheels are for the deck shell only mechanical components/parts such as prescribed in the operator's manual; (f) Abuse, misuse, neglect, modifications, alterations, normal wear, improper servicing, use of unauthorized ...or oils, failure to improper set up or return of or broken strainers; However, registering your nearest authorized Husqvarna Servicing Dealer, call Husqvarna, at www.usa.husqvarna.com (US & Canada) to help ensure, among other things, that resulting from abuse or neglect of ...
Owners Manual
Page 33
...Warranty * No Warranty No Warranty Generators Engine* Other Non-Expendable Components* Spreaders * * *2 Years (2nd Year Parts Only) *2 Years-1365GN (2nd Year Parts Only) * No Warranty 33 Armor Protected Limited Warranty 10 Years No Warranty Fabricated Deck shell. Limited Lifetime Warranty... than Rental Use) Riding Lawn Tractors: Frame, Chassis, Front Axle 5 Years No Warranty Engine* * * Transmission (if made by Husqvarna/Peerless) 3 Years No Warranty Transmission (if third party)** ** ** XLS Models only - Consumer Wheeled Limited Warranty Chart 2012 Consumer (personal...
...Warranty * No Warranty No Warranty Generators Engine* Other Non-Expendable Components* Spreaders * * *2 Years (2nd Year Parts Only) *2 Years-1365GN (2nd Year Parts Only) * No Warranty 33 Armor Protected Limited Warranty 10 Years No Warranty Fabricated Deck shell. Limited Lifetime Warranty... than Rental Use) Riding Lawn Tractors: Frame, Chassis, Front Axle 5 Years No Warranty Engine* * * Transmission (if made by Husqvarna/Peerless) 3 Years No Warranty Transmission (if third party)** ** ** XLS Models only - Consumer Wheeled Limited Warranty Chart 2012 Consumer (personal...
Owners Manual
Page 34
... Deck shell is for the BALANCE of two (2) decks within the Limited Lifetime Warranty. One (1) Year Commercial warranty, parts & labor, with Hydro-Gear Distributor network. Two (2) Year Consumer warranty, parts & labor, with Husqvarna. Two (2) Year Consumer warranty, parts & labor, with Hydro-Gear Distributor network. *** "Limited Lifetime Warranty" on specific Snow Throwers & Tillers, warranty through...
... Deck shell is for the BALANCE of two (2) decks within the Limited Lifetime Warranty. One (1) Year Commercial warranty, parts & labor, with Hydro-Gear Distributor network. Two (2) Year Consumer warranty, parts & labor, with Husqvarna. Two (2) Year Consumer warranty, parts & labor, with Hydro-Gear Distributor network. *** "Limited Lifetime Warranty" on specific Snow Throwers & Tillers, warranty through...
Parts Manual
Page 5
TRACTOR - Switch Seat Switch Ign Key/Chain Switch Light/Reset Harness Ign. inches 1 inch = 25.4 mm 5 LGT2654 (96045004000), PRODUCT NO. 960 45 00-40 ELECTRICAL KEY PART NO. Harness Pigtail 12 V Outlet NOTE: All component dimensions given in U.S. MODEL NO. Dash Screw Thd Cut 1/4-20 x 1/2 Cover Terminal Red Solenoid Gauge Hourmeter Switch ...
TRACTOR - Switch Seat Switch Ign Key/Chain Switch Light/Reset Harness Ign. inches 1 inch = 25.4 mm 5 LGT2654 (96045004000), PRODUCT NO. 960 45 00-40 ELECTRICAL KEY PART NO. Harness Pigtail 12 V Outlet NOTE: All component dimensions given in U.S. MODEL NO. Dash Screw Thd Cut 1/4-20 x 1/2 Cover Terminal Red Solenoid Gauge Hourmeter Switch ...
Parts Manual
Page 7
... Tank Crossmember Screw 10-24 x 5/8 Bushing Steering Chassis Dash Lower Bolt 5/16-18 x 1-1/4 Screw 5/16-18 x 3/4 Insert RH Nut Lock Hex Flange 5/16-18 KEY PART NO. NO. Lens LH Grille Asm. NO. LGT2654 (96045004000), PRODUCT NO. 960 45 00-40 CHASSIS KEY...
... Tank Crossmember Screw 10-24 x 5/8 Bushing Steering Chassis Dash Lower Bolt 5/16-18 x 1-1/4 Screw 5/16-18 x 3/4 Insert RH Nut Lock Hex Flange 5/16-18 KEY PART NO. NO. Lens LH Grille Asm. NO. LGT2654 (96045004000), PRODUCT NO. 960 45 00-40 CHASSIS KEY...
Parts Manual
Page 9
LGT2654 (96045004000), PRODUCT NO. 960 45 00-40 DRIVE KEY PART NO. Pedal Brake Control Console Asm. NO. 166 532 42 91-64 167 532 ... 5/16-18 x 3/4 Screw 5/16-18 x 1/2 Retainer Spring Pin Cotter 1/8 x 3/4 Retainer Clip Spring Return Clutch Spacer Transaxle 18 and 22 KEY PART NO. inches 1 inch = 25.4 mm 9 NO. 1 ------ 2 532 18 62-11 7 532 19 98-44 9 532 14 00-80 15...16 94-84 161 532 10 57-09 162 532 19 57-85 DESCRIPTION Transaxle, TUFFTORQ K46 AW (448354) (Order parts from transaxle manufacturer.) Key Hub Asm. Spring Brake Rod Shift Knob Rod, Brake Ring E Rod Brake Park Cover Foot...
LGT2654 (96045004000), PRODUCT NO. 960 45 00-40 DRIVE KEY PART NO. Pedal Brake Control Console Asm. NO. 166 532 42 91-64 167 532 ... 5/16-18 x 3/4 Screw 5/16-18 x 1/2 Retainer Spring Pin Cotter 1/8 x 3/4 Retainer Clip Spring Return Clutch Spacer Transaxle 18 and 22 KEY PART NO. inches 1 inch = 25.4 mm 9 NO. 1 ------ 2 532 18 62-11 7 532 19 98-44 9 532 14 00-80 15...16 94-84 161 532 10 57-09 162 532 19 57-85 DESCRIPTION Transaxle, TUFFTORQ K46 AW (448354) (Order parts from transaxle manufacturer.) Key Hub Asm. Spring Brake Rod Shift Knob Rod, Brake Ring E Rod Brake Park Cover Foot...