Owner's Manual
Page 3
Table of Contents important information...5 Tools...6 uninstalling the existing unit...9 wire labels...10 installing the thermostat...13 settings...23 methods of operation...27 Default Programs Chart...36 ICONS AND FEATURES...43 Important features...54 Wiring Diagrams...55 troubleshooting...58 Warranty...61 3
Table of Contents important information...5 Tools...6 uninstalling the existing unit...9 wire labels...10 installing the thermostat...13 settings...23 methods of operation...27 Default Programs Chart...36 ICONS AND FEATURES...43 Important features...54 Wiring Diagrams...55 troubleshooting...58 Warranty...61 3
Owner's Manual
Page 7
The wires must be labeled prior to removal to ensure proper reconnection. 7 Do not disconnect the wires from the existing thermostat before reading these instructions. RC Y G W RC Y G W w NOTICE!
The wires must be labeled prior to removal to ensure proper reconnection. 7 Do not disconnect the wires from the existing thermostat before reading these instructions. RC Y G W RC Y G W w NOTICE!
Owner's Manual
Page 9
...the main power panel or at the furnace. (Failure to turn off the power to access the wires from the existing thermostat. See page 8 for common examples.) 3. Locate, but do not disconnect the wires. (If wires are not visible, they may have multiple covers, screws or other locking devices that open to ...the back of the wall plate. Turn the system power OFF from the wall. (Some thermostats may have doors that must be connected to expose the wires and mounting screws.) 9 Some models may be removed or disengaged. Remove the existing...
...the main power panel or at the furnace. (Failure to turn off the power to access the wires from the existing thermostat. See page 8 for common examples.) 3. Locate, but do not disconnect the wires. (If wires are not visible, they may have multiple covers, screws or other locking devices that open to ...the back of the wall plate. Turn the system power OFF from the wall. (Some thermostats may have doors that must be connected to expose the wires and mounting screws.) 9 Some models may be removed or disengaged. Remove the existing...
Owner's Manual
Page 10
label the wire with this sticker: RH / R / VR / 4 24 Volt RH RC / VC 24 Volt cool RC Y / C* / M / O air conditioning compressor W / H / B G / F Y1 heating Y/0 W/B fan G heat pump compressor Y1 10 Y1 G W/B Y/0 RC RH wire labels if your existing thermostat is marked...
label the wire with this sticker: RH / R / VR / 4 24 Volt RH RC / VC 24 Volt cool RC Y / C* / M / O air conditioning compressor W / H / B G / F Y1 heating Y/0 W/B fan G heat pump compressor Y1 10 Y1 G W/B Y/0 RC RH wire labels if your existing thermostat is marked...
Owner's Manual
Page 11
..., contact a qualified HVAC technician.) W RC Y G W Note: Wire colors do not connect it to the existing terminal designation for non-battery powered thermostats. 5. This wire is used . Do not let the wires slip back into the wall during disconnection. After all wires are labeled, disconnect each wire according to the Wire Labels chart. (If the terminals are both...
..., contact a qualified HVAC technician.) W RC Y G W Note: Wire colors do not connect it to the existing terminal designation for non-battery powered thermostats. 5. This wire is used . Do not let the wires slip back into the wall during disconnection. After all wires are labeled, disconnect each wire according to the Wire Labels chart. (If the terminals are both...
Owner's Manual
Page 13
If the existing holes do not match those on the wall and pull the labeled wires through the opening. 3. installing the thermostat INSTALLING THE WALL PLATE 1. Position the new wall plate on the Hunter wall plate, or if there are no existing holes, visually level the wall plate and mark the wall for two holes. 13 Remove the wall plate from the new thermostat by pressing the release tab on the bottom of the thermostat. 2.
If the existing holes do not match those on the wall and pull the labeled wires through the opening. 3. installing the thermostat INSTALLING THE WALL PLATE 1. Position the new wall plate on the Hunter wall plate, or if there are no existing holes, visually level the wall plate and mark the wall for two holes. 13 Remove the wall plate from the new thermostat by pressing the release tab on the bottom of the thermostat. 2.
Owner's Manual
Page 15
installing the thermostat, cont. 4. Tap the plastic anchors into the anchors. Insert the mounting screws through the opening. Reposition the wall plate on the wall, pulling the wires through the wall plate and into the holes until they are flush with the wall. (Do not use plastic anchors if you encounter a stud in the wall.) 6. Remove the wall plate and drill two 3/16" holes where marked. 5. Verify that the wall plate is visually level and securely tighten both screws. 15
installing the thermostat, cont. 4. Tap the plastic anchors into the anchors. Insert the mounting screws through the opening. Reposition the wall plate on the wall, pulling the wires through the wall plate and into the holes until they are flush with the wall. (Do not use plastic anchors if you encounter a stud in the wall.) 6. Remove the wall plate and drill two 3/16" holes where marked. 5. Verify that the wall plate is visually level and securely tighten both screws. 15
Owner's Manual
Page 17
...wire length back into the wall.) 3. Wires should be inserted behind the black terminal shields. Push any extra wires should be individually wrapped in place. 2. CONNECTING THE WIRES Jumper G RC RH Y W 1. If you have both an RH and RC wire.... Loosen, but do not provide both an RH and RC wire... the wires from the wall to prevent interference. 17 If you do not have both an RH and RC wire, remove this jumper. Note: A jumper wire has ...
...wire length back into the wall.) 3. Wires should be inserted behind the black terminal shields. Push any extra wires should be individually wrapped in place. 2. CONNECTING THE WIRES Jumper G RC RH Y W 1. If you have both an RH and RC wire.... Loosen, but do not provide both an RH and RC wire... the wires from the wall to prevent interference. 17 If you do not have both an RH and RC wire, remove this jumper. Note: A jumper wire has ...
Owner's Manual
Page 60
Manual operation instructions are on pages 28-31. 60 My system continues to operate when the thermostat is in the off position. 7 a. Replace unit 9. troubleshooting (cont.) 7. Replace unit. 7 b. Check your system for proper wiring. 8. How do I just operate my thermostat manually? 9 a. The LCD screen permanently reads HI, LO, or ERR. 8 a.
Manual operation instructions are on pages 28-31. 60 My system continues to operate when the thermostat is in the off position. 7 a. Replace unit 9. troubleshooting (cont.) 7. Replace unit. 7 b. Check your system for proper wiring. 8. How do I just operate my thermostat manually? 9 a. The LCD screen permanently reads HI, LO, or ERR. 8 a.