Specifications
Page 6
Packaging...37 7.0. Signal definitions ...40 7.4. Acoustics...35 6.6.1 Sound power levels 35 6.6.2 Discrete tone penalty 35 6.7. Cabling...39 7.2. PIO timings...45 7.8. Reliability ...26 6.3.1 Data Reliability ...26 6.3.2 Failure prediction (S.M.A.R.T 27 6.3.3 Cable noise interference 27 6.3.4 Service life ... MIC mark ...36 6.9. Ultra DMA timings...47 7.9.1 Initiating Read DMA 47 7.9.2 Host Pausing Read DMA 48 Travelstar 5K100 Hard Disk Drive Specification ii Reset timings ...44 7.7. 6.3. Mechanical specifications 30 6.4.1 Physical dimensions and weight 30 6.4.2 Mounting hole...
Packaging...37 7.0. Signal definitions ...40 7.4. Acoustics...35 6.6.1 Sound power levels 35 6.6.2 Discrete tone penalty 35 6.7. Cabling...39 7.2. PIO timings...45 7.8. Reliability ...26 6.3.1 Data Reliability ...26 6.3.2 Failure prediction (S.M.A.R.T 27 6.3.3 Cable noise interference 27 6.3.4 Service life ... MIC mark ...36 6.9. Ultra DMA timings...47 7.9.1 Initiating Read DMA 47 7.9.2 Host Pausing Read DMA 48 Travelstar 5K100 Hard Disk Drive Specification ii Reset timings ...44 7.7. 6.3. Mechanical specifications 30 6.4.1 Physical dimensions and weight 30 6.4.2 Mounting hole...
Specifications
Page 41
... 5 years or 20,000 power on hours, which comes first, under the following commands: • Hard reset • Standby Travelstar 5K100 Hard Disk Drive Specification 27 The details are covered by the purchase agreement. 6.3.5 Preventive maintenance None 6.3.6 Load/unload The product...and torque. • The interface physical and electrical requirements of the drive should satisfy ATA-6. • The power-off sequence described in Section 6.3.6.2, "Required Power-Off Sequence" on page 168. 6.3.3 Cable noise interference To avoid any warranty or warranty period. Function Set (B0h...
... 5 years or 20,000 power on hours, which comes first, under the following commands: • Hard reset • Standby Travelstar 5K100 Hard Disk Drive Specification 27 The details are covered by the purchase agreement. 6.3.5 Preventive maintenance None 6.3.6 Load/unload The product...and torque. • The interface physical and electrical requirements of the drive should satisfy ATA-6. • The power-off sequence described in Section 6.3.6.2, "Required Power-Off Sequence" on page 168. 6.3.3 Cable noise interference To avoid any warranty or warranty period. Function Set (B0h...
Specifications
Page 53
... on page 31 show the connector and pin location. 7.0 Electrical interface specification 7.1 Cabling The maximum cable length from the host system to the hard disk drive plus circuit pattern length in the host system shall not exceed 18 inches. 7.2 ...Interface connector The signal connector for AT attachment is left blank for correct connector insertion. The figure below and "" on page 55 for correct address setting.) Travelstar 5K100 Hard Disk Drive...
... on page 31 show the connector and pin location. 7.0 Electrical interface specification 7.1 Cabling The maximum cable length from the host system to the hard disk drive plus circuit pattern length in the host system shall not exceed 18 inches. 7.2 ...Interface connector The signal connector for AT attachment is left blank for correct connector insertion. The figure below and "" on page 55 for correct address setting.) Travelstar 5K100 Hard Disk Drive...
Specifications
Page 56
...before asserting PDIAG-, as a Slave. If the host connects to Travelstar 5K100 Hard Disk Drive Specification 42 is negated, the line is busy and has not yet passed its drive diagnostics. within 1 ms (to indicate to 3.3 volts in the drive through a 10 k. The signal level of the first valid ... after negation of DIOR- If device 1 is driven low at the falling edge of DASP-, either drive may assert DASP- to drive an LED indicator on the same AT interface cable to post status. PDIAGThis signal shall be asserted by device 1 during reset initialization, device 0 shall ...
...before asserting PDIAG-, as a Slave. If the host connects to Travelstar 5K100 Hard Disk Drive Specification 42 is negated, the line is busy and has not yet passed its drive diagnostics. within 1 ms (to indicate to 3.3 volts in the drive through a 10 k. The signal level of the first valid ... after negation of DIOR- If device 1 is driven low at the falling edge of DASP-, either drive may assert DASP- to drive an LED indicator on the same AT interface cable to post status. PDIAGThis signal shall be asserted by device 1 during reset initialization, device 0 shall ...
Specifications
Page 69
... not spin up at shipment is Setting 1 (no jumper). Travelstar 5K100 Hard Disk Drive Specification 55 If pin 28 is ground (or low), the drive is a Slave. When the drive address is Cable Select, the address depends on the interface connector determines the drive address. 7.10 Drive address setting A jumper placed on the condition of pin 28 of...
... not spin up at shipment is Setting 1 (no jumper). Travelstar 5K100 Hard Disk Drive Specification 55 If pin 28 is ground (or low), the drive is a Slave. When the drive address is Cable Select, the address depends on the interface connector determines the drive address. 7.10 Drive address setting A jumper placed on the condition of pin 28 of...
Specifications
Page 225
Hitachi Global Storage Technologies Index Drive handling precautions, 4 Drive ready time, 16 A Acoustics, 35 Address Feature Set, 89 Address Offset Feature, 85 Advanced Power Management (ABLE-3) feature, 75 Appendix, 205 B BSMI mark, 36 C Cable noise interference, 27 Capacity, formatted, 11 CE mark, 36 Check Power Mode, 102 Command descriptions, 97 Command overhead, ...67 Load/unload, 27 M Magnetic fields, 25 Mechanical positioning, 14 Mechanical specifications, 30 Mode transition time, 17 Mounting hole locations, 31 Mounting orientation, 31 Travelstar 5K100 Hard Disk Drive Specification 211
Hitachi Global Storage Technologies Index Drive handling precautions, 4 Drive ready time, 16 A Acoustics, 35 Address Feature Set, 89 Address Offset Feature, 85 Advanced Power Management (ABLE-3) feature, 75 Appendix, 205 B BSMI mark, 36 C Cable noise interference, 27 Capacity, formatted, 11 CE mark, 36 Check Power Mode, 102 Command descriptions, 97 Command overhead, ...67 Load/unload, 27 M Magnetic fields, 25 Mechanical positioning, 14 Mechanical specifications, 30 Mode transition time, 17 Mounting hole locations, 31 Mounting orientation, 31 Travelstar 5K100 Hard Disk Drive Specification 211