Specifications
Page 6
......40 7.4. Multi word DMA timings 46 7.9. Packaging...37 7.0. Mechanical specifications 30 6.4.1 Physical dimensions and weight 30 6.4.2 Mounting hole locations 31 6.4.3 Connector and jumper ...description 31 6.4.4 Mounting orientation 31 6.4.5 Load/unload mechanism 32 6.5. Electromagnetic compatibility 36 6.8.1 CE mark ...36 6.8.2 C-TICK mark ...36 6.8.3 BSMI mark ...36 6.8.4 MIC mark ...36 6.9. Signal descriptions...41 7.5. PIO timings...45 7.8. Ultra DMA timings...47 7.9.1 Initiating Read DMA 47 7.9.2 Host Pausing Read DMA 48 Travelstar 5K100 Hard Disk Drive...
......40 7.4. Multi word DMA timings 46 7.9. Packaging...37 7.0. Mechanical specifications 30 6.4.1 Physical dimensions and weight 30 6.4.2 Mounting hole locations 31 6.4.3 Connector and jumper ...description 31 6.4.4 Mounting orientation 31 6.4.5 Load/unload mechanism 32 6.5. Electromagnetic compatibility 36 6.8.1 CE mark ...36 6.8.2 C-TICK mark ...36 6.8.3 BSMI mark ...36 6.8.4 MIC mark ...36 6.9. Signal descriptions...41 7.5. PIO timings...45 7.8. Ultra DMA timings...47 7.9.1 Initiating Read DMA 47 7.9.2 Host Pausing Read DMA 48 Travelstar 5K100 Hard Disk Drive...
Specifications
Page 45
...screw torque is 3.0±0.5 kgf-cm. Travelstar 5K100 Hard Disk Drive Specification 31 Performance and error rate will stay within specification limits if the drive is operated in Section 7.10, "Drive address setting" on page 39. 6.4.4 Mounting orientation The drive will operate in a horizontal orientation will ... tilted ±5degrees from which it was formatted. Thus a drive formatted in all axes (six directions) and will be able to designate the drive address as either master or slave. The jumper setting method is described in the other permissible orientations from these ...
...screw torque is 3.0±0.5 kgf-cm. Travelstar 5K100 Hard Disk Drive Specification 31 Performance and error rate will stay within specification limits if the drive is operated in Section 7.10, "Drive address setting" on page 39. 6.4.4 Mounting orientation The drive will operate in a horizontal orientation will ... tilted ±5degrees from which it was formatted. Thus a drive formatted in all axes (six directions) and will be able to designate the drive address as either master or slave. The jumper setting method is described in the other permissible orientations from these ...
Specifications
Page 50
..., place of manufacture, and UL/ CSA logos. • Labels containing jumper information if required by Hitachi" or equivalent, part number, EC number, and FRU number. • A bar code label which is based on "Telecommunications Basic Act" and "Radio Waves Act". Travelstar 5K100 Hard Disk Drive Specification 36 The EC marking for certification of information and...
..., place of manufacture, and UL/ CSA logos. • Labels containing jumper information if required by Hitachi" or equivalent, part number, EC number, and FRU number. • A bar code label which is based on "Telecommunications Basic Act" and "Radio Waves Act". Travelstar 5K100 Hard Disk Drive Specification 36 The EC marking for certification of information and...
Specifications
Page 56
...-. Caution When DASP- This line is pulled up to avoid incorrect insertion. Drive 1 shall then assert PDIAG- If device 1 is present then device 0 shall wait up to Travelstar 5K100 Hard Disk Drive Specification 42 CSEL (Cable Select) This signal is monitored to assert PDIAG-. KEY Pin position...post its diagnostics and is not present, device 0 may assert DASP- to 5.0V through a 10 k. for drive 1 to determine the drive address (master or slave) when the jumper on the same AT interface cable to 00h. device drivers. The signal level may be negated following acceptance of DASP...
...-. Caution When DASP- This line is pulled up to avoid incorrect insertion. Drive 1 shall then assert PDIAG- If device 1 is present then device 0 shall wait up to Travelstar 5K100 Hard Disk Drive Specification 42 CSEL (Cable Select) This signal is monitored to assert PDIAG-. KEY Pin position...post its diagnostics and is not present, device 0 may assert DASP- to 5.0V through a 10 k. for drive 1 to determine the drive address (master or slave) when the jumper on the same AT interface cable to 00h. device drivers. The signal level may be negated following acceptance of DASP...
Specifications
Page 69
... a Master. Travelstar 5K100 Hard Disk Drive Specification 55 Two addresses require the setting of the AT interface cable. If pin 28 is ground (or low), the drive is grounded, the drive does not spin up at shipment is a Slave. If pin 28 is open (or logic high), the drive is Setting 1 (no jumper). When the drive address is...
... a Master. Travelstar 5K100 Hard Disk Drive Specification 55 Two addresses require the setting of the AT interface cable. If pin 28 is ground (or low), the drive is grounded, the drive does not spin up at shipment is a Slave. If pin 28 is open (or logic high), the drive is Setting 1 (no jumper). When the drive address is...
Specifications
Page 131
...Semi-duplex mode is enabled 5(=X) 1=Device 0 detected Device 1 4(=X) 1=Device 1 passed diagnostic 3(=X) 1=Device 0 passed diagnostic 2-1(=X) how Device 0 determined the device number: 00=Reserved 01=a jumper was used 10=the CSEL signal was used 11= some other method used or the method unknown 0(=1) Always Automatic Acoustic Management value 15- 8 Vendor's Recommended...bit Address feature set 0000H Reserved 0000H Removable Media Status Notification feature set by model." above ViH 0=Device detected CBLID- Travelstar 5K100 Hard Disk Drive Specification 117 on page 119.
...Semi-duplex mode is enabled 5(=X) 1=Device 0 detected Device 1 4(=X) 1=Device 1 passed diagnostic 3(=X) 1=Device 0 passed diagnostic 2-1(=X) how Device 0 determined the device number: 00=Reserved 01=a jumper was used 10=the CSEL signal was used 11= some other method used or the method unknown 0(=1) Always Automatic Acoustic Management value 15- 8 Vendor's Recommended...bit Address feature set 0000H Reserved 0000H Removable Media Status Notification feature set by model." above ViH 0=Device detected CBLID- Travelstar 5K100 Hard Disk Drive Specification 117 on page 119.