GVA-24-Valve-Actuator-Installation-Manual-092051BRevE
Page 1
092051B RevE GVA-24 Valve Actuator Installation Manual \ Contents Introduction 2 Installation 2 Maintenance 5 Troubleshooting 5 Warranty Back GVA-24 Hayward Industries 400 Connell Drive, Suite 6100 Berkeley Heights, NJ 07922 Phone: (908) 355-7995 www.hayward.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
092051B RevE GVA-24 Valve Actuator Installation Manual \ Contents Introduction 2 Installation 2 Maintenance 5 Troubleshooting 5 Warranty Back GVA-24 Hayward Industries 400 Connell Drive, Suite 6100 Berkeley Heights, NJ 07922 Phone: (908) 355-7995 www.hayward.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
GVA-24-Valve-Actuator-Installation-Manual-092051BRevE
Page 4
Using the chart below for cam settings for reinstallation later. 2. GVA MOUNTING OPTION A (Standard) B C D PORT WHERE WATER ENTERS 1 2 (std) 3 1 2 3 1 2 3 1 2 3 CAM SETTING LOWER CAM 6 o'clock 12 o'clock 3 o'clock 9 o'clock 3 o'clock 6 o'clock 3 o'clock 9 ... 12 o'clock PORT WHERE WATER EXITS PORT 2 1 1 2 1 1 2 1 1 2 1 1 PORT 3 3 2 3 3 2 3 3 2 3 3 2 Two Port Valve The Model GVA-24 Actuator may be mounted to the valve in this manual to the image on the cover. 3 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Remove four (4) screws from the valve. In all cases, the cam settings are the...
Using the chart below for cam settings for reinstallation later. 2. GVA MOUNTING OPTION A (Standard) B C D PORT WHERE WATER ENTERS 1 2 (std) 3 1 2 3 1 2 3 1 2 3 CAM SETTING LOWER CAM 6 o'clock 12 o'clock 3 o'clock 9 o'clock 3 o'clock 6 o'clock 3 o'clock 9 ... 12 o'clock PORT WHERE WATER EXITS PORT 2 1 1 2 1 1 2 1 1 2 1 1 PORT 3 3 2 3 3 2 3 3 2 3 3 2 Two Port Valve The Model GVA-24 Actuator may be mounted to the valve in this manual to the image on the cover. 3 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Remove four (4) screws from the valve. In all cases, the cam settings are the...
GVA-24-Valve-Actuator-Installation-Manual-092051BRevE
Page 5
...Do not overtighten - Refer to the charts on the bottom of the GVA-24 actuator. Unscrew the Locking Knob above the handle approximately 4 full turns (see below). When changing the cam settings, move the valve position manually. Remove the four (4) screws which is always 12 o'clock (see below...ON1 and ON2 position. The toggle switch on the previous pages to ON1 or ON2 position. Follow the instructions below ). 4 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Out of synchroniza- 5. Slide the cams off pool filtration just in place. Replace cover and handle and tighten screws and ...
...Do not overtighten - Refer to the charts on the bottom of the GVA-24 actuator. Unscrew the Locking Knob above the handle approximately 4 full turns (see below). When changing the cam settings, move the valve position manually. Remove the four (4) screws which is always 12 o'clock (see below...ON1 and ON2 position. The toggle switch on the previous pages to ON1 or ON2 position. Follow the instructions below ). 4 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Out of synchroniza- 5. Slide the cams off pool filtration just in place. Replace cover and handle and tighten screws and ...
GVA-24-Valve-Actuator-Installation-Manual-092051BRevE
Page 6
...turning it clicks, then tighten the Locking Knob. 5 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS See "Maintenance" section in this problem would be moved in any position. 6. This condition may happen when the GVA-24 O-ring seals are located at the top and bottom of lubricant ...around the actuator shaft where it enters the cover. 4. To return the actuator to automatic position, pull up on the Locking Knob to be a draining or overflowing spa. 3. Spread a small amount of this manual....
...turning it clicks, then tighten the Locking Knob. 5 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS See "Maintenance" section in this problem would be moved in any position. 6. This condition may happen when the GVA-24 O-ring seals are located at the top and bottom of lubricant ...around the actuator shaft where it enters the cover. 4. To return the actuator to automatic position, pull up on the Locking Knob to be a draining or overflowing spa. 3. Spread a small amount of this manual....
GVA-24-Valve-Actuator-Installation-Manual-092051BRevE
Page 7
... repair. If there is covered for cartage, removal, repair or installation labor or any nature. Hayward shall not be responsible for a period of the product. Material supplied or workmanship performed by others in the owners manual(s). 5. Problems resulting from failure to maintain pool water chemistry in accordance with the recommendations in process...
... repair. If there is covered for cartage, removal, repair or installation labor or any nature. Hayward shall not be responsible for a period of the product. Material supplied or workmanship performed by others in the owners manual(s). 5. Problems resulting from failure to maintain pool water chemistry in accordance with the recommendations in process...