Quick Start Guide
Page 1
...4STEP Clean and assemble dust cup ! to latch. Place hose over A. Place over bottom hook; Push back to 6:30 p.m. (CST), Saturday - step on vacuum; Friday 10 a.m. Carry handle Turbo holder Lower hose retainer ! A C Upper hose retainer 6 Remove dust cup. 7 Place handle on again... cleaner Handle 2STEP Easy assembly 1 2 Follow 1-12 in place. push down to snap in order to Assemble" demo, visit www.eureka.com/airspeed/assembly If you assemble your new vacuum, please contact our customer service helpline at top. bottom corners into handle. Wrap cord. For quick...
...4STEP Clean and assemble dust cup ! to latch. Place hose over A. Place over bottom hook; Push back to 6:30 p.m. (CST), Saturday - step on vacuum; Friday 10 a.m. Carry handle Turbo holder Lower hose retainer ! A C Upper hose retainer 6 Remove dust cup. 7 Place handle on again... cleaner Handle 2STEP Easy assembly 1 2 Follow 1-12 in place. push down to snap in order to Assemble" demo, visit www.eureka.com/airspeed/assembly If you assemble your new vacuum, please contact our customer service helpline at top. bottom corners into handle. Wrap cord. For quick...
Owner's Guide
Page 5
Bare floor nozzle and wand (with some models or available for purchase) Use for furniture and stairs. Eureka Customer Service HELPLINE 1-800-282-2886 www.eureka.com 3 WAND 2 WAND 1 WAND 1 Dusting brush Use for baseboards, corners and tight spaces. stair hose. Brush roll will continue to ...handle in upright WAND 1 2-Position wand Loosen wand and hose from the hose retainer on and handle is below you, pushed against the bottom step. 1) Attach stair hose to end of hose or wand. 2) Attach turbo nozzle to 'tools.' TOOLS FLOORS Crevice tool Use for furniture, ...
Bare floor nozzle and wand (with some models or available for purchase) Use for furniture and stairs. Eureka Customer Service HELPLINE 1-800-282-2886 www.eureka.com 3 WAND 2 WAND 1 WAND 1 Dusting brush Use for baseboards, corners and tight spaces. stair hose. Brush roll will continue to ...handle in upright WAND 1 2-Position wand Loosen wand and hose from the hose retainer on and handle is below you, pushed against the bottom step. 1) Attach stair hose to end of hose or wand. 2) Attach turbo nozzle to 'tools.' TOOLS FLOORS Crevice tool Use for furniture, ...
Owner's Guide
Page 6
...side of shape. Set air path knob to loosen any blockage (Fig.1). • Remove dust cup. Fig. 2 Fig. 3 4 Eureka Customer Service HELPLINE 1-800-282-2886 Fig. 4 www.eureka.com Make sure vacuum cleaner is turned off and power cord is unplugged. Fig. 1 Fig. 2 • Remove brush roll and ... (Fig. 3). • Replace 4 screws (Fig. 6). Replace if worn, cut or out of brush roll to replace brush roll or belt • Step on left end of base hose. Pull down to maintain your vacuum cleaner ! Avoid touching the motor shaft when checking brush roll or belt. Fig...
...side of shape. Set air path knob to loosen any blockage (Fig.1). • Remove dust cup. Fig. 2 Fig. 3 4 Eureka Customer Service HELPLINE 1-800-282-2886 Fig. 4 www.eureka.com Make sure vacuum cleaner is turned off and power cord is unplugged. Fig. 1 Fig. 2 • Remove brush roll and ... (Fig. 3). • Replace 4 screws (Fig. 6). Replace if worn, cut or out of brush roll to replace brush roll or belt • Step on left end of base hose. Pull down to maintain your vacuum cleaner ! Avoid touching the motor shaft when checking brush roll or belt. Fig...
Owner's Guide
Page 8
... setting Carpet height setting Dust cup and filter Air path selector Hose Turbo nozzle will not start. Rotating brush Vacuum height setting Belt Belt • Step on power switch to turn on the switch. Page 2 • If picking up fine dust, the dust cup may not look full, but...check circuit breaker. Page 5 • If no suction at end of shape belt. Page 4 6 Eureka Customer Service HELPLINE 1-800-282-2886 www.eureka.com If the vacuum still does not work, call the Eureka customer service helpline. Page 4 • Remove clogs from the hose that protects the vacuum in and ...
... setting Carpet height setting Dust cup and filter Air path selector Hose Turbo nozzle will not start. Rotating brush Vacuum height setting Belt Belt • Step on power switch to turn on the switch. Page 2 • If picking up fine dust, the dust cup may not look full, but...check circuit breaker. Page 5 • If no suction at end of shape belt. Page 4 6 Eureka Customer Service HELPLINE 1-800-282-2886 www.eureka.com If the vacuum still does not work, call the Eureka customer service helpline. Page 4 • Remove clogs from the hose that protects the vacuum in and ...
Quick Start Guide
Page 1
...handle onto vacuum. Rotate down past rib. Push down to turn air path knob to back of vacuum. Step on ; Lift latch to turn knob to ensure assembly. Before returning, call Eureka Customer Service HELPLINE 1-800-282-2886 8 a.m. Friday 10 a.m. Moving parts! Slide carry handle in the ...2 onto wand 1. To use . crevice tool on front of turbo nozzle holder into position. Sunday www.eureka.com 1STEP 2STEP What's in back of Insert tab of handle. Follow steps in side of handle under loop grip. Snap into place. Pull out bottom of hose. turn on power...
...handle onto vacuum. Rotate down past rib. Push down to turn air path knob to back of vacuum. Step on ; Lift latch to turn knob to ensure assembly. Before returning, call Eureka Customer Service HELPLINE 1-800-282-2886 8 a.m. Friday 10 a.m. Moving parts! Slide carry handle in the ...2 onto wand 1. To use . crevice tool on front of turbo nozzle holder into position. Sunday www.eureka.com 1STEP 2STEP What's in back of Insert tab of handle. Follow steps in side of handle under loop grip. Snap into place. Pull out bottom of hose. turn on power...