Instruction Manual
Page 4
... water supply connected and turned on. NOTICE: The pump was filled with the dipstick or vented cap (supplied) may be removed and replaced with a shipping plug. Engine Refer to the pump and will void the warranty. 2 Change the pump oil after the first 50 hours of operation and ... high pressure hose by depressing trigger until a steady stream of water is SIMPSON® Premium Pump Crankcase Oil. The preferred oil is present. Running the unit WITHOUT removing and replacing the shipping plug with oil at the factory. Release quick connect coupler and twist nozzle to make...
... water supply connected and turned on. NOTICE: The pump was filled with the dipstick or vented cap (supplied) may be removed and replaced with a shipping plug. Engine Refer to the pump and will void the warranty. 2 Change the pump oil after the first 50 hours of operation and ... high pressure hose by depressing trigger until a steady stream of water is SIMPSON® Premium Pump Crankcase Oil. The preferred oil is present. Running the unit WITHOUT removing and replacing the shipping plug with oil at the factory. Release quick connect coupler and twist nozzle to make...
Instruction Manual
Page 14
... engine until it with water on water supply. 8. SIMPSON® / POWERWASHER™ Pump Guard is drained, replace pump oil drain plug. Change the pump oil after the first 50 hours of pump. 2. Loosen pump oil fill plug 28 . 2. Reconnect spray wand to test. Add Ethanol Shield™...pressure washer frame is equipped with an oil drain hole to back flush loosened particles for 30 seconds. Tighten securely. 5. Replace pump oil fill plug and tighten securely. Clean the nozzle immediately using the nozzle kit supplied and the following the manufacturer's instructions....
... engine until it with water on water supply. 8. SIMPSON® / POWERWASHER™ Pump Guard is drained, replace pump oil drain plug. Change the pump oil after the first 50 hours of pump. 2. Loosen pump oil fill plug 28 . 2. Reconnect spray wand to test. Add Ethanol Shield™...pressure washer frame is equipped with an oil drain hole to back flush loosened particles for 30 seconds. Tighten securely. 5. Replace pump oil fill plug and tighten securely. Clean the nozzle immediately using the nozzle kit supplied and the following the manufacturer's instructions....
Instruction Manual
Page 15
... bottle and remove seal. 3. The manufacturer will honor the terms of all water from repairs using replacement lances or guns with this pressure washer as proof of pump. 5. NOTICE: Risk of property damage. NOTICE: Risk of property damage. Always store and transport unit in gun holder. 3. ...and are final. This warranty covers defects in the instruction manual shall void warranty. The manufacturer's warranty obligation is damage from your DeWALT pressure washer, report the concern to 1-877-362-4271 or [email protected] for authorization and direction to water inlet of ...
... bottle and remove seal. 3. The manufacturer will honor the terms of all water from repairs using replacement lances or guns with this pressure washer as proof of pump. 5. NOTICE: Risk of property damage. NOTICE: Risk of property damage. Always store and transport unit in gun holder. 3. ...and are final. This warranty covers defects in the instruction manual shall void warranty. The manufacturer's warranty obligation is damage from your DeWALT pressure washer, report the concern to 1-877-362-4271 or [email protected] for authorization and direction to water inlet of ...
Instruction Manual
Page 17
...solution. 20 Chemical too thick. 21 Worn seal or packing. 22 Chemical build up after two pulls on water source. Check and replace. 33 Pump overfilled. Move choke to remove any blockage. Place engine ON/OFF switch in ON position. 7 Choke lever in the CHOKE position. Squeeze .... 24 Worn unloader piston. 25 Worn or broken o-ring. 26 Loose hose connection. 27 Piston packings worn. 28 Pump head or tubes damaged from freezing. Check and replace. Check and replace. Clean vent plug; Refer to the NO CHOKE pos ition. Water supply must be the same consistency...
...solution. 20 Chemical too thick. 21 Worn seal or packing. 22 Chemical build up after two pulls on water source. Check and replace. 33 Pump overfilled. Move choke to remove any blockage. Place engine ON/OFF switch in ON position. 7 Choke lever in the CHOKE position. Squeeze .... 24 Worn unloader piston. 25 Worn or broken o-ring. 26 Loose hose connection. 27 Piston packings worn. 28 Pump head or tubes damaged from freezing. Check and replace. Check and replace. Clean vent plug; Refer to the NO CHOKE pos ition. Water supply must be the same consistency...