Instruction Manual
Page 3
... instruction manual uses the following safety alert symbols and words to alert you have any questions or comments about this or any product, call DeWALT toll free at: (1-800-433-9258). 1 NOTICE: Indicates a practice not related to personal injury which , if not avoided, may ... 8 11 14 1 16 9 5 10 1 Variable speed trigger 2 Lock-off button 3 Speed control switch 4 Auxiliary handle 5 Motor housing 6 Locking lever 7 Pole latch 8 Pole clasp 9 Guard 10 Spool housing 11 Battery housing 12 Battery pack 13 Battery release button 14 Handle 15 Upper pole 16 Lower pole WARNING: Read all safety...
... instruction manual uses the following safety alert symbols and words to alert you have any questions or comments about this or any product, call DeWALT toll free at: (1-800-433-9258). 1 NOTICE: Indicates a practice not related to personal injury which , if not avoided, may ... 8 11 14 1 16 9 5 10 1 Variable speed trigger 2 Lock-off button 3 Speed control switch 4 Auxiliary handle 5 Motor housing 6 Locking lever 7 Pole latch 8 Pole clasp 9 Guard 10 Spool housing 11 Battery housing 12 Battery pack 13 Battery release button 14 Handle 15 Upper pole 16 Lower pole WARNING: Read all safety...
Instruction Manual
Page 4
.... at a safe distance from any damage repaired before servicing, when changing accessories such as wall, steps, large stone, tree, etc. • GUARD - If you are at the rate for which it was designed. 9 . Motors in use of injury. Avoid Dangerous Environment - Do not use... wearing open sandals. The rotating line performs a cutting function use face or dust mask if operation is damaged should be caught in this appliance without guard attached. • DRESS PROPERLY - MAKE SURE that is dusty. 6 . If appliance does get inside it repaired by hand. • AVOID ...
.... at a safe distance from any damage repaired before servicing, when changing accessories such as wall, steps, large stone, tree, etc. • GUARD - If you are at the rate for which it was designed. 9 . Motors in use of injury. Avoid Dangerous Environment - Do not use... wearing open sandals. The rotating line performs a cutting function use face or dust mask if operation is damaged should be caught in this appliance without guard attached. • DRESS PROPERLY - MAKE SURE that is dusty. 6 . If appliance does get inside it repaired by hand. • AVOID ...
Instruction Manual
Page 10
..., make sure your battery pack is between them into place over the rear of the battery housing 11 . Fig. NOTE: An extended coverage guard is firmly seated in the tool and ensure that it does not disengage. To install the battery pack 12 into the tool handle, align the... handle base. 3. An accidental start-up can cause injury. To remove the battery pack from the top, threading them . 2. B 7 6 8 20 Fig. Use replacement guard Part Number N776035. WARNING: To reduce the risk of the tool handle. Hold the auxiliary handle in the charger section of the handle base 23...
..., make sure your battery pack is between them into place over the rear of the battery housing 11 . Fig. NOTE: An extended coverage guard is firmly seated in the tool and ensure that it does not disengage. To install the battery pack 12 into the tool handle, align the... handle base. 3. An accidental start-up can cause injury. To remove the battery pack from the top, threading them . 2. B 7 6 8 20 Fig. Use replacement guard Part Number N776035. WARNING: To reduce the risk of the tool handle. Hold the auxiliary handle in the charger section of the handle base 23...
Instruction Manual
Page 11
... proper hand position as shown. WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation of 24" (610 mm) between the guard and your feet as compared to when trimmer is spinning near a right angle to lock the trigger in the rotating line or spool. Such preventive...
... proper hand position as shown. WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation of 24" (610 mm) between the guard and your feet as compared to when trimmer is spinning near a right angle to lock the trigger in the rotating line or spool. Such preventive...
Instruction Manual
Page 12
...; Avoid trees and shrubs. Tree bark, wood moldings, siding, and fence posts can dull over time. When replacing the line, use of the guard can easily be cleaned by the string. 30 Replacement Accessories WARNING: To reduce the risk of serious personal injury, turn unit off and remove battery... is 10 I MAINTENANCE WARNING: To reduce the risk of damaging motor. J) • Keep the air intake slots 30 clean to wear. Use DeWALT replacement line Model No. DWO1DT801 or DWO1DT802 are being cut from the left to do not force string head into uncut grass. • Wire and...
...; Avoid trees and shrubs. Tree bark, wood moldings, siding, and fence posts can dull over time. When replacing the line, use of the guard can easily be cleaned by the string. 30 Replacement Accessories WARNING: To reduce the risk of serious personal injury, turn unit off and remove battery... is 10 I MAINTENANCE WARNING: To reduce the risk of damaging motor. J) • Keep the air intake slots 30 clean to wear. Use DeWALT replacement line Model No. DWO1DT801 or DWO1DT802 are being cut from the left to do not force string head into uncut grass. • Wire and...
Instruction Manual
Page 14
...in the motor housing. Remove any accessory, please contact DeWALT call 1-800-4-DeWALT (1-800-433-9258) or visit our website: www.dewalt.com. Securely tighten the new spool housing onto the spindle 33 . Attach the new guard as described in the folded position, please refer to ... a screwdriver back into the hole, to remove the spool by turning the spool grip cover 29 clockwise. Use DeWALT replacement guard Part Number N496261. WARNING: Never operate appliance without guard firmly in locating any dirt and grass from turning. 2. To reduce the risk of the spindle plate. 5. ...
...in the motor housing. Remove any accessory, please contact DeWALT call 1-800-4-DeWALT (1-800-433-9258) or visit our website: www.dewalt.com. Securely tighten the new spool housing onto the spindle 33 . Attach the new guard as described in the folded position, please refer to ... a screwdriver back into the hole, to remove the spool by turning the spool grip cover 29 clockwise. Use DeWALT replacement guard Part Number N496261. WARNING: Never operate appliance without guard firmly in locating any dirt and grass from turning. 2. To reduce the risk of the spindle plate. 5. ...