Dell PowerConnect 2708 Support and Manuals
Get Help and Manuals for this Dell item
View All Support Options Below
Free Dell PowerConnect 2708 manuals!
Problems with Dell PowerConnect 2708?
Ask a Question
Free Dell PowerConnect 2708 manuals!
Problems with Dell PowerConnect 2708?
Ask a Question
Most Recent Dell PowerConnect 2708 Questions
Dell Powerconnect 2708 Will Not Go To Management
(Posted by rimsee 9 years ago)
Popular Dell PowerConnect 2708 Manual Pages
Information Update - Page 1
... the factory default settings. It is reset to change the IP address of each switch that you can update the switch IP Address either: • Manually, or • By enabling DHCP Addressing
NOTE: To update the IP address, see the Dell PowerConnect 27xx Systems User's Guide.
NOTE: The Managed Mode LED is not illuminated when the switch is recessed to Web-managed mode and the Managed Mode...
Getting Started Guide - Page 12
...booted successfully.
Booting the Switch
When the device is connected to a power source, the device LEDs glow indicating that you obtain the most recent revision of the user documentation from the Dell Support website at support.dell.com. NOTE: Before proceeding, read the release notes for configuring the default route.
10
Getting Started Guide Setup of the management interface.
User's Guide - Page 3
... 9 MAC Address Supported Features 11 Layer 2 Features 11 VLAN Supported Features 12 Class of Service (CoS) Features 12 Ethernet Switch Management Features 13 Port Default Settings 13
2 Hardware Description
Switch Port Configurations 15 PowerConnect 2708/2716/2724/2748 Front Panel Port Description . . . . 15
Physical Dimensions 19
LED Definitions 19 Power LED 19 Managed Mode LED 19...
User's Guide - Page 7
... PowerConnect 2708 switch supports 8 GbE copper ports.
7 Figure 1-1.
1
Introduction
This User's Guide contains the information needed for the Small Office/Home Office (SOHO) that requires high performance network connectivity along with advanced web management features.The PowerConnect management features are primarily for installing, configuring and maintaining the PowerConnect 2708...
User's Guide - Page 9
... Secure Mode when the Managed Mode button is set to OFF. From Managed Mode, when the Managed Mode button is there a web management interface and thus cannot be managed. Back Pressure Support On half-duplex links, the receiving port prevents buffer overflows by removing the IP address to links operating at the end of the queue. The user may enable or disable this applies to the switch so...
User's Guide - Page 10
...switches is available on 10/100/1000BASE-T Ethernet ports.
The Jumbo Frames Support feature, utilizes the network optimally by the user. Virtual Cable Testing (VCT) VCT technology provides the mechanism to configure the port speeds advertised. Port... when the link is crossed or straight through. Auto Negotiation Auto negotiation allows an Ethernet switch to advertise modes of this ...
User's Guide - Page 12
... contents. The information replied is an extension to form a single Link Aggregated Group (LAG).
Link Aggregation The PowerConnect 2708/2716/2724/2748 switches support up to four member ports to BootP. DHCP is then used to define various services for supporting bandwidth management and control is based on their ingress port. The BootP client is operational if there is a corrupted or...
User's Guide - Page 15
.... The Gigabit Ethernet ports can only operate at 10, 100 or 1000 Mbps. Figure 2-1. 2
Hardware Description
Switch Port Configurations
PowerConnect 2708/2716/2724/2748 Front Panel Port Description
The Dell™ PowerConnect™ 2708, 2716, 2724 and 2748 switches use 10/100/1000BASE-T ports on the front panel, restores the device's default settings configuration.
15 A Managed Mode push...
User's Guide - Page 26
...Before unpacking the device, inspect the packaging and report any evidence of these components.
If you suspect a problem with different power feeders. • General - to Dell.
Before installing the unit, verify that the site selected for Managed Mode Operation" explains how to set the switch to avoid sources of electrical noise such as radio transmitters, broadcast amplifiers...
User's Guide - Page 40
... a Web browser. 2 Enter the Ethernet Switch IP address (the default IP address is configured with a default IP address, user login and password. Activating the Managed Mode button recovers the factory default setting (no password).
For information about recovering a lost password, see "Viewing System IP Address."
3 When the Enter Network Password window opens, enter a user name and password...
User's Guide - Page 44
... the amount of time since the last switch reset. The switch status parameters are then set the static IP Address, Subnet Mask and the device's static Default Gateway Address. The system time is updated. Service Tag -
Viewing System IP Address
The IP Addressing page enables to manage the device. System Up Time- Secure Mode (2748 only) - Asset Tag (0-16 Characters) - System...
User's Guide - Page 55
...:
Software Image - Downloading Files from which file is downloaded to PowerConnect 2748 switch configuration only. The destination file type to download. 3 Define the fields on the page. 4 Click Apply Changes. File Download (PowerConnect 2708, 2716, and 2724 Switch Configuration)
TFTP Server IP Address - Source File Name (1-64 Characters) - Boot Code - Downloading Files From...
User's Guide - Page 56
... is recommended to designate that the nonactive image will become the active image after reset, and then to be downloaded. Downloads the image file. Firmware Download Server IP Address - Destination File Name - It is downloaded. File Download (PowerConnect 2748 Switch Configuration)
Firmware Download - Enables initiating an image download via TFTP - The possible field values are...
User's Guide - Page 65
...on network links, Storm Control mechanism controls the amount of packet Storm Control. The Storm Control page is enabled. Storm Control (PowerConnect 2708 Configuration)
Port - Enables or disables forwarding Broadcast packet types on a per-port basis, to configure the settings of frames entering the switch. In addition to all ports on the designated VLANs on the switch. Broadcast Mode...
User's Guide - Addendum - Page 7
... files are donloaded. The Destination File can be either the Software Image file, or the Boot Code image. NOTE: The TFTP Server application can be downloaded. The TFTP Server IP Address specifies the location from software vendors.
7 Configuring LAG Membership
The following screen shows an example of Link Aggregation configuration, whereby LAG Group 4 consists of member ports 5, 6, and 7.
Dell PowerConnect 2708 Reviews
We have not received any reviews for Dell yet.