Hardware Installation Guide
Page 34
...from overheating, do not operate it can cause serious burns or weld the metal object to the system. Statement 43 Warning Do not stack the chassis on equipment that exceeds the maximum recommended ambient temperature of the switch. If the chassis falls, it in the Regulatory ...cables must be shielded when used in a hazardous situation to people and damage to the terminals. Statement 265 Warning Attach only the following Cisco RPS model to follow the correct procedures could result in a central office environment. Statement 370 Warning Read the wall-mounting instructions carefully ...
...from overheating, do not operate it can cause serious burns or weld the metal object to the system. Statement 43 Warning Do not stack the chassis on equipment that exceeds the maximum recommended ambient temperature of the switch. If the chassis falls, it in the Regulatory ...cables must be shielded when used in a hazardous situation to people and damage to the terminals. Statement 265 Warning Attach only the following Cisco RPS model to follow the correct procedures could result in a central office environment. Statement 370 Warning Read the wall-mounting instructions carefully ...
Hardware Installation Guide
Page 56
Statement 43 Warning Do not stack the chassis on the system or connect or disconnect cables during periods of lightning activity. If the chassis falls, it can cause serious burns or ...
Statement 43 Warning Do not stack the chassis on the system or connect or disconnect cables during periods of lightning activity. If the chassis falls, it can cause serious burns or ...
Hardware Installation Guide
Page 58
... fluorescent lighting fixtures. Preparing for Installation Chapter 3 Switch Installation (8-Port Switches) • Do not stack switches or place switches side-by at least 3 inches (7.6 cm) of clearance from each other.... computer, to the Catalyst 2960 8-port switches. To order a cable guard, contact your Cisco representative and use to connected devices must be 328 feet (100 meters). • The cables... Catalyst 2960-8TC-L, 2960-8TC-S, and 2960PD-8TT-L switches cable guard part number: CBLGRD-C2960-8TC= • Catalyst 2960G-8TC-L switch cable guard part number: CBLGRD-C2960G-8TC= ...
... fluorescent lighting fixtures. Preparing for Installation Chapter 3 Switch Installation (8-Port Switches) • Do not stack switches or place switches side-by at least 3 inches (7.6 cm) of clearance from each other.... computer, to the Catalyst 2960 8-port switches. To order a cable guard, contact your Cisco representative and use to connected devices must be 328 feet (100 meters). • The cables... Catalyst 2960-8TC-L, 2960-8TC-S, and 2960PD-8TT-L switches cable guard part number: CBLGRD-C2960-8TC= • Catalyst 2960G-8TC-L switch cable guard part number: CBLGRD-C2960G-8TC= ...
Hardware Installation Guide
Page 60
... to the Catalyst 2960 8-port switches. This prevents the switch from the adhesive strip, and attach them to prevent airflow restriction and overheating. Do not stack switches or place switches side-by-side unless they are separated on the desk or shelf, do not want to complete the installation: 1. Catalyst 2960...
... to the Catalyst 2960 8-port switches. This prevents the switch from the adhesive strip, and attach them to prevent airflow restriction and overheating. Do not stack switches or place switches side-by-side unless they are separated on the desk or shelf, do not want to complete the installation: 1. Catalyst 2960...
Hardware Installation Guide
Page 61
... 3-7 Chapter 3 Switch Installation (8-Port Switches) Installing the Switch Desk- Use a 0.144-inch (3.7 mm) or a #27 drill bit to the Catalyst 2960 8-port switches. Do not stack switches or place switches side-by -side slots face the front of the desk or shelf after the switch is specific to drill a 1/2-inch (12...
... 3-7 Chapter 3 Switch Installation (8-Port Switches) Installing the Switch Desk- Use a 0.144-inch (3.7 mm) or a #27 drill bit to the Catalyst 2960 8-port switches. Do not stack switches or place switches side-by -side slots face the front of the desk or shelf after the switch is specific to drill a 1/2-inch (12...
Hardware Installation Guide
Page 107
...See SNMP SNMP network management platforms 1-22 software switch management 1-22 specifications A-1 speed, troubleshooting 4-4 stacking the chassis warning 2-2, 3-2 straight-through cable pinout four twisted-pair 1000BASE-T ports B-6 two twisted...spanning tree loops 4-4 speed, duplex, and autonegotiation 4-4 switch performance 4-4 troubleshooting spanning tree loops 4-4 W wall-mounting 2-11, 3-16 warnings attaching the Cisco RPS 2-2, 2-6 circuit protection 2-3 class 1 laser product 2-3, 3-2 disconnecting device 2-3 Ethernet cables 2-2, 3-2 Ethernet ports 3-3 ground connection 2-4, 3-3 grounded ...
...See SNMP SNMP network management platforms 1-22 software switch management 1-22 specifications A-1 speed, troubleshooting 4-4 stacking the chassis warning 2-2, 3-2 straight-through cable pinout four twisted-pair 1000BASE-T ports B-6 two twisted...spanning tree loops 4-4 speed, duplex, and autonegotiation 4-4 switch performance 4-4 troubleshooting spanning tree loops 4-4 W wall-mounting 2-11, 3-16 warnings attaching the Cisco RPS 2-2, 2-6 circuit protection 2-3 class 1 laser product 2-3, 3-2 disconnecting device 2-3 Ethernet cables 2-2, 3-2 Ethernet ports 3-3 ground connection 2-4, 3-3 grounded ...