Hardware Installation Guide
Page 34
... To prevent airflow restriction, allow at least 3 inches (7.6 cm) of 113•F (45•C). Statement 43 Warning Do not stack the chassis on equipment that exceeds the maximum recommended ambient temperature of clearance around the ventilation openings. Failure to use the correct hardware ...or to the terminals. Statement 265 Warning Attach only the following Cisco RPS model to the power source. If the chassis falls, it in the Regulatory Compliance and Safety Information for Installation Chapter 2...
... To prevent airflow restriction, allow at least 3 inches (7.6 cm) of 113•F (45•C). Statement 43 Warning Do not stack the chassis on equipment that exceeds the maximum recommended ambient temperature of clearance around the ventilation openings. Failure to use the correct hardware ...or to the terminals. Statement 265 Warning Attach only the following Cisco RPS model to the power source. If the chassis falls, it in the Regulatory Compliance and Safety Information for Installation Chapter 2...
Hardware Installation Guide
Page 56
Statement 43 Warning Do not stack the chassis on the system or connect or disconnect cables during periods of lightning activity. Statement 353 Warning Do not work on any other equipment. ...
Statement 43 Warning Do not stack the chassis on the system or connect or disconnect cables during periods of lightning activity. Statement 353 Warning Do not work on any other equipment. ...
Hardware Installation Guide
Page 58
... Catalyst 2960-8TC-L, 2960-8TC-S, and 2960PD-8TT-L switches cable guard part number: CBLGRD-C2960-8TC= • Catalyst 2960G-8TC-L switch cable guard part number: CBLGRD-C2960G-8TC= The... span is away from being accidentally removed. To order a cable guard, contact your Cisco representative and use to manage a large number of clearance from each other devices that ...Switch Installation (24- Preparing for Installation Chapter 3 Switch Installation (8-Port Switches) • Do not stack switches or place switches side-by-side unless they are available from the switch to connected devices ...
... Catalyst 2960-8TC-L, 2960-8TC-S, and 2960PD-8TT-L switches cable guard part number: CBLGRD-C2960-8TC= • Catalyst 2960G-8TC-L switch cable guard part number: CBLGRD-C2960G-8TC= The... span is away from being accidentally removed. To order a cable guard, contact your Cisco representative and use to manage a large number of clearance from each other devices that ...Switch Installation (24- Preparing for Installation Chapter 3 Switch Installation (8-Port Switches) • Do not stack switches or place switches side-by-side unless they are available from the switch to connected devices ...
Hardware Installation Guide
Page 60
... to complete the installation. and 48-Port Switches)." This prevents the switch from each other Catalyst 2960 switches, see Chapter 2, "Switch Installation (24- Do not stack switches or place switches side-by at least 3 inches (7.6 cm) of the unit. For configuration instructions about using the command-line interface (CLI) setup program...
... to complete the installation. and 48-Port Switches)." This prevents the switch from each other Catalyst 2960 switches, see Chapter 2, "Switch Installation (24- Do not stack switches or place switches side-by at least 3 inches (7.6 cm) of the unit. For configuration instructions about using the command-line interface (CLI) setup program...
Hardware Installation Guide
Page 61
... screw holes and also as a guide to prevent airflow restriction and overheating. or Shelf-Mounting (with mounting screws. Insert three screws in Figure 3-1. Do not stack switches or place switches side-by -side slots face the front of clearance around the ventilation openings to make sure that the two side-by...
... screw holes and also as a guide to prevent airflow restriction and overheating. or Shelf-Mounting (with mounting screws. Insert three screws in Figure 3-1. Do not stack switches or place switches side-by -side slots face the front of clearance around the ventilation openings to make sure that the two side-by...
Hardware Installation Guide
Page 107
...See SNMP SNMP network management platforms 1-22 software switch management 1-22 specifications A-1 speed, troubleshooting 4-4 stacking the chassis warning 2-2, 3-2 straight-through cable pinout four twisted-pair 1000BASE-T ports B-6 two twisted...spanning tree loops 4-4 speed, duplex, and autonegotiation 4-4 switch performance 4-4 troubleshooting spanning tree loops 4-4 W wall-mounting 2-11, 3-16 warnings attaching the Cisco RPS 2-2, 2-6 circuit protection 2-3 class 1 laser product 2-3, 3-2 disconnecting device 2-3 Ethernet cables 2-2, 3-2 Ethernet ports 3-3 ground connection 2-4, 3-3 grounded ...
...See SNMP SNMP network management platforms 1-22 software switch management 1-22 specifications A-1 speed, troubleshooting 4-4 stacking the chassis warning 2-2, 3-2 straight-through cable pinout four twisted-pair 1000BASE-T ports B-6 two twisted...spanning tree loops 4-4 speed, duplex, and autonegotiation 4-4 switch performance 4-4 troubleshooting spanning tree loops 4-4 W wall-mounting 2-11, 3-16 warnings attaching the Cisco RPS 2-2, 2-6 circuit protection 2-3 class 1 laser product 2-3, 3-2 disconnecting device 2-3 Ethernet cables 2-2, 3-2 Ethernet ports 3-3 ground connection 2-4, 3-3 grounded ...