Hardware Installation Guide
Page 34
... is connected to the system. Statement 1004 Catalyst 2960 Switch Hardware Installation Guide 2-2 OL-7075-09 Statement 265 Warning Attach only the following Cisco RPS model to the terminals. Failure to use the correct hardware or to follow the correct procedures could result in an area that is ...not connected to the power source. Statement 43 Warning Do not stack the chassis on the back of lightning activity. Statement 17B Warning Before working on the system or connect or disconnect cables during periods ...
... is connected to the system. Statement 1004 Catalyst 2960 Switch Hardware Installation Guide 2-2 OL-7075-09 Statement 265 Warning Attach only the following Cisco RPS model to the terminals. Failure to use the correct hardware or to follow the correct procedures could result in an area that is ...not connected to the power source. Statement 43 Warning Do not stack the chassis on the back of lightning activity. Statement 17B Warning Before working on the system or connect or disconnect cables during periods ...
Hardware Installation Guide
Page 56
... the bottom to a power-over-ethernet (PoE) IEEE 802.3af compliant power source or an IEC60950 compliant limited power source. Statement 43 Warning Do not stack the chassis on the system or connect or disconnect cables during periods of the rack. • If the rack is provided with the heaviest component...
... the bottom to a power-over-ethernet (PoE) IEEE 802.3af compliant power source or an IEC60950 compliant limited power source. Statement 43 Warning Do not stack the chassis on the system or connect or disconnect cables during periods of the rack. • If the rack is provided with the heaviest component...
Hardware Installation Guide
Page 58
...; Catalyst 2960-8TC-L, 2960-8TC-S, and 2960PD-8TT-L switches cable guard part number: CBLGRD-C2960-8TC= • Catalyst 2960G-8TC-L switch cable guard part number: CBLGRD-C2960G-8TC= The...secure cables to the Catalyst 2960 8-port switches. To order a cable guard, contact your Cisco representative and use shorter lengths of single-mode fiber-optic cable, you should insert a ... for unrestricted cabling. - Preparing for Installation Chapter 3 Switch Installation (8-Port Switches) • Do not stack switches or place switches side-by at least 3 inches (7.6 cm) of clearance from each other. ...
...; Catalyst 2960-8TC-L, 2960-8TC-S, and 2960PD-8TT-L switches cable guard part number: CBLGRD-C2960-8TC= • Catalyst 2960G-8TC-L switch cable guard part number: CBLGRD-C2960G-8TC= The...secure cables to the Catalyst 2960 8-port switches. To order a cable guard, contact your Cisco representative and use shorter lengths of single-mode fiber-optic cable, you should insert a ... for unrestricted cabling. - Preparing for Installation Chapter 3 Switch Installation (8-Port Switches) • Do not stack switches or place switches side-by at least 3 inches (7.6 cm) of clearance from each other. ...
Hardware Installation Guide
Page 60
... command-line interface (CLI) setup program, go to Appendix C, "Configuring the Switch with Rack-Mount Brackets), page 3-16 Desk- and 48-Port Switches)." Do not stack switches or place switches side-by at least 3 inches (7.6 cm) of clearance around the ventilation openings to a Dual-Purpose Port" section on top of the...
... command-line interface (CLI) setup program, go to Appendix C, "Configuring the Switch with Rack-Mount Brackets), page 3-16 Desk- and 48-Port Switches)." Do not stack switches or place switches side-by at least 3 inches (7.6 cm) of clearance around the ventilation openings to a Dual-Purpose Port" section on top of the...
Hardware Installation Guide
Page 61
... shown in the slots on the screw template, and tighten them until they are separated on the top of the desk or shelf. Do not stack switches or place switches side-by -side slots face the front of clearance from the desk or shelf.
... shown in the slots on the screw template, and tighten them until they are separated on the top of the desk or shelf. Do not stack switches or place switches side-by -side slots face the front of clearance from the desk or shelf.
Hardware Installation Guide
Page 107
...See SNMP SNMP network management platforms 1-22 software switch management 1-22 specifications A-1 speed, troubleshooting 4-4 stacking the chassis warning 2-2, 3-2 straight-through cable pinout four twisted-pair 1000BASE-T ports B-6 two twisted...spanning tree loops 4-4 speed, duplex, and autonegotiation 4-4 switch performance 4-4 troubleshooting spanning tree loops 4-4 W wall-mounting 2-11, 3-16 warnings attaching the Cisco RPS 2-2, 2-6 circuit protection 2-3 class 1 laser product 2-3, 3-2 disconnecting device 2-3 Ethernet cables 2-2, 3-2 Ethernet ports 3-3 ground connection 2-4, 3-3 grounded ...
...See SNMP SNMP network management platforms 1-22 software switch management 1-22 specifications A-1 speed, troubleshooting 4-4 stacking the chassis warning 2-2, 3-2 straight-through cable pinout four twisted-pair 1000BASE-T ports B-6 two twisted...spanning tree loops 4-4 speed, duplex, and autonegotiation 4-4 switch performance 4-4 troubleshooting spanning tree loops 4-4 W wall-mounting 2-11, 3-16 warnings attaching the Cisco RPS 2-2, 2-6 circuit protection 2-3 class 1 laser product 2-3, 3-2 disconnecting device 2-3 Ethernet cables 2-2, 3-2 Ethernet ports 3-3 ground connection 2-4, 3-3 grounded ...