Cisco WS-C2960-24TC-S Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WS-C2960-24TC-S manuals!
Problems with Cisco WS-C2960-24TC-S?
Ask a Question
Free Cisco WS-C2960-24TC-S manuals!
Problems with Cisco WS-C2960-24TC-S?
Ask a Question
Cisco WS-C2960-24TC-S Videos
Cisco WS-C2960-24TC-S $465 Price Reduction
Duration: :34
Total Views: 10
Duration: :34
Total Views: 10
Cisco WS-C2960-24TC-S $465 Price Reduction
Duration: :34
Total Views: 64
Duration: :34
Total Views: 64
Buy Cisco WS-C2960-24TC-L Switch $440.00 ? 3Anetwork.com
Duration: :35
Total Views: 11
Duration: :35
Total Views: 11
Popular Cisco WS-C2960-24TC-S Manual Pages
Software Guide - Page 31
... • Cisco Redundant Power System 2300 Hardware Installation Guide (order number DOC-7817647=) • For more information about the Network Admission Control (NAC) features, see the "Downloading Software" section in the "Obtaining Documentation, Obtaining Support, and Security Guidelines" section on page xxxii. • Release Notes for the Catalyst 3750, 3560, 2970, and 2960 Switches (not...
Software Guide - Page 34
... the LEDs on all switch ports for optimizing bandwidth
Catalyst 2960 Switch Software Configuration Guide
1-2
OL-8603-04 Interactive guide mode that guides you to provide only the minimum required information to 16 switches that can be made more information about the device manager, see the getting started guide.
• User-defined and Cisco-default Smartports macros for creating...
Software Guide - Page 81
... convention. OL-8603-04
Catalyst 2960 Switch Software Configuration Guide
4-3
ConfigID
Each configured switch has a unique ConfigID, which to their destinations. Chapter 4 Configuring Cisco IOS CNS Agents
Understanding Cisco Configuration Engine Software
Event Service
The Cisco Configuration Engine uses the Event Service for receipt and generation of switch CLI attributes. The event...
Software Guide - Page 107
... system starts up and keeps track of the time service is the system clock. This clock runs from the Cisco.com page under Documentation > Cisco IOS Software > 12.2 Mainline > Command References. This chapter consists of these sources: • NTP • Manual configuration
OL-8603-04
Catalyst 2960 Switch Software Configuration Guide
6-1 Note For complete syntax and usage information for...
Software Guide - Page 227
...and SFP module ports, the port numbers restart with the interface configuration commands that will run on page 10-6). If there is selected:
Switch(config)# interface gigabitethernet0/1 Switch(config-if)#
Note You do not need to display information about a specific interface or all interface configuration processes.
OL-8603-04
Catalyst 2960 Switch Software Configuration Guide
10...
Software Guide - Page 233
...
Catalyst 2960 Switch Software Configuration Guide
10-11 If you enable a dual-purpose uplink port through the shutdown and the no media-type interface configuration command.
For information about setting the speed and duplex, see the information that link. Return to the SFP module interface.
In this port, it cannot attain a link even if the SFP module side is down , the switch...
Software Guide - Page 273
... exit
end show running-config
Step 8 show vlan
Step 9 configure terminal Step 10 interface gigabitethernet0/1
Step 11 Step 12 Step 13
spanning-tree vlan 2-4 cost 30 end
Step 14...Catalyst 2960 Switch Software Configuration Guide
12-23
Each time an unknown MAC address is used to support dynamic-access ports, which are set the spanning-tree path cost to a VLAN, but can act as trunk ports...
Software Guide - Page 281
... in the network. OL-8603-04
Catalyst 2960 Switch Software Configuration Guide
13-1 VTP only learns about VLANs to other switches. Extended-range VLANs (VLAN IDs greater than 1005) are sent through VTP to 1005). Using VTP, you can cause several problems, such as duplicate VLAN names, incorrect VLAN-type specifications, and security violations.
Note For complete...
Software Guide - Page 304
... for an interface.
15-2
Catalyst 2960 Switch Software Configuration Guide
OL-8603-04 The algorithm calculates the best loop-free path through a switched Layer 2 network by assigning a role to change the default for every switched LAN segment
• Alternate-A blocked port providing an alternate path to a single LAN segment or a switched LAN of its ports as the designated role or...
Software Guide - Page 371
...04
Catalyst 2960 Switch Software Configuration Guide
18-5
The VLAN interface is only supported on IGMP Version 2 hosts. Note You should only use . IGMP Configurable-Leave Timer
You can be set either... removes the group for all ports in a specific multicast group. For configuration steps, see the "Enabling IGMP Immediate Leave" section on page 18-10. Chapter 18 Configuring IGMP Snooping...
Software Guide - Page 518
...port to a queue-set by using the queue-set in the ratio calculation. You assign shared or shaped weights to support...default settings are serviced. The reason for non-IP packets the DSCP is enabled, in which the SRR scheduler sends packets from each queue-set...-18
Catalyst 2960 Switch Software Configuration Guide
OL-8603-04 only an indication of the egress queues and if these settings do ...
Software Guide - Page 622
...switch: flash_init
If you had set the console port speed to anything other than 9600, it has been reset to match that of the switch console port. This file contains the password definition.
32-4
Catalyst 2960 Switch Software Configuration Guide... Password
Chapter 32 Troubleshooting
Several lines of information about the software appear with instructions, informing you if the password ...
Software Guide - Page 636
.... For a description of the fields in privileged EXEC mode, and most debug commands take no form of lower network traffic and fewer users. Debugging during periods of the command.
32-18
Catalyst 2960 Switch Software Configuration Guide
OL-8603-04 For this reason, use debug commands to diagnose and resolve internetworking problems: • Enabling Debugging on a Specific Feature...
Software Guide - Page 700
...-18
IN-6
Catalyst 2960 Switch Software Configuration Guide
CoS-to-DSCP map for QoS 28-52 counters, clearing interface 10-19 crashinfo file 32-21 critical authentication, IEEE 802.1x 9-33 cryptographic software image
SSH 8-33 SSL 8-37 CWDM SFPs 1-17
D
daylight saving time 6-13 debugging
enabling all system diagnostics 32-19 enabling for a specific feature 32-18...
Software Guide - Page 715
... with other features 19-10
port-shutdown response, VMPS 12-24 port VLAN ID TLV 21-2 power management TLV 21-2, 21-6 preferential treatment of traffic
See QoS preventing unauthorized access 8-1 priority
overriding CoS 14-6 trusting CoS 14-6 private VLAN edge ports See protected ports privileged EXEC mode 2-2 privilege levels changing the default for lines 8-9 command switch 5-15 exiting 8-9 logging...
Cisco WS-C2960-24TC-S Reviews
We have not received any reviews for Cisco yet.