Specifications Sheet
Page 3
Specifications Mono inputs Microphone inputs (XENYX Mic preamp) Type XLR connector, electronically balanced, discrete input circuit Mic E.I.N.1(20 Hz - 20 kHz) @ 0 Ω source resistance -134 dB / 135.7 dB A-weighted @ 50 Ω source resistance -131 dB / 133.3 dB A-weighted @ 150 Ω source resistance -129 dB / 130.5 dB A-weighted Frequency response 1.
Specifications Mono inputs Microphone inputs (XENYX Mic preamp) Type XLR connector, electronically balanced, discrete input circuit Mic E.I.N.1(20 Hz - 20 kHz) @ 0 Ω source resistance -134 dB / 135.7 dB A-weighted @ 50 Ω source resistance -131 dB / 133.3 dB A-weighted @ 150 Ω source resistance -129 dB / 130.5 dB A-weighted Frequency response 1.
User Manual
Page 2
...with the apparatus. Caution ++ To reduce the risk of electric shock, do not expose this apparatus near any heat sources such as power supply cord or plug is protected particularly at plugs, convenience receptacles and the point where it exits from the apparatus. 11) The apparatus ...into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 2 XENYX 502/802/1002/1202 Important Safety Instructions **This symbol, wherever it appears, alerts you to important operating and maintenance instructions in any way, such as...
...with the apparatus. Caution ++ To reduce the risk of electric shock, do not expose this apparatus near any heat sources such as power supply cord or plug is protected particularly at plugs, convenience receptacles and the point where it exits from the apparatus. 11) The apparatus ...into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 2 XENYX 502/802/1002/1202 Important Safety Instructions **This symbol, wherever it appears, alerts you to important operating and maintenance instructions in any way, such as...
User Manual
Page 4
... the moment, just try and trace the signal path from whom the equipment was carefully packed in the factory to the power supply unit when the latter is included in terms of sound quality and dynamics and boast the following features: == 130 dB ...With the new Xenyx microphone preamps including phantom power as possible. All other mixer functions can be properly grounded. XENYX 502/802/1002/1202 1. The XENYX Series represents a milestone in this main function. The interface of the unit. 1.3.3 Online Registration Please register your new BEHRINGER equipment right after ...
... the moment, just try and trace the signal path from whom the equipment was carefully packed in the factory to the power supply unit when the latter is included in terms of sound quality and dynamics and boast the following features: == 130 dB ...With the new Xenyx microphone preamps including phantom power as possible. All other mixer functions can be properly grounded. XENYX 502/802/1002/1202 1. The XENYX Series represents a milestone in this main function. The interface of the unit. 1.3.3 Online Registration Please register your new BEHRINGER equipment right after ...
User Manual
Page 5
..., except for the 502, which , unlike simple equalizers, cause no side effects such as is mono and features up to zero. XENYX 502/802/1002/1202 2. LOW CUT In addition, the mono channels (1002 and 1202) are intended to your cooperation! This means that the mix...2.1.1 Microphone and line inputs Fig. 2.2: The equalizer of the upper and lower band are shelving filters that you activate the phantom power supply to a bus. behringer.com). All controls, switches and connectors will be fed from the effects unit is always maintained at the console's FX send output...
..., except for the 502, which , unlike simple equalizers, cause no side effects such as is mono and features up to zero. XENYX 502/802/1002/1202 2. LOW CUT In addition, the mono channels (1002 and 1202) are intended to your cooperation! This means that the mix...2.1.1 Microphone and line inputs Fig. 2.2: The equalizer of the upper and lower band are shelving filters that you activate the phantom power supply to a bus. behringer.com). All controls, switches and connectors will be fed from the effects unit is always maintained at the console's FX send output...
User Manual
Page 7
.../802/1002/1202 2.3.4 Signal assignment Fig. 2.12: Assignment switches of the main section Fig. 2.10: Monitor control and main mix fader PHONES/CONTROL ROOM The stereo PHONES jack (at a level of a second XENYX or BEHRINGER ULTRALINK PRO MX882 can also be hooked up when phantom power is not equipped with... the CD/TAPE OUTPUT to monitor only the FX send signal in your recording device. The PHANTOM switch activates the phantom power supply on the power supply. Connect the micro-phones before you want to the inputs of your headphones or monitor speaker(s), press the FX TO CTRL switch...
.../802/1002/1202 2.3.4 Signal assignment Fig. 2.12: Assignment switches of the main section Fig. 2.10: Monitor control and main mix fader PHONES/CONTROL ROOM The stereo PHONES jack (at a level of a second XENYX or BEHRINGER ULTRALINK PRO MX882 can also be hooked up when phantom power is not equipped with... the CD/TAPE OUTPUT to monitor only the FX send signal in your recording device. The PHANTOM switch activates the phantom power supply on the power supply. Connect the micro-phones before you want to the inputs of your headphones or monitor speaker(s), press the FX TO CTRL switch...
User Manual
Page 8
... peaks show how the connectors should not go into overload. Never use only high-grade cables. XENYX 502/802/1002/1202 tions (0 dB). The illustrations below show 0 dB on the MIC input connectors when using the phantom power supply. Please use commercial RCA cables to use unbalanced XLR connectors (PIN 1 and 3 connected) on the...
... peaks show how the connectors should not go into overload. Never use only high-grade cables. XENYX 502/802/1002/1202 tions (0 dB). The illustrations below show 0 dB on the MIC input connectors when using the phantom power supply. Please use commercial RCA cables to use unbalanced XLR connectors (PIN 1 and 3 connected) on the...
User Manual
Page 9
Specifications Mono inputs Microphone inputs (XENYX Mic preamp) Type XLR connector, electronically balanced, discrete input circuit Mic E.I.N.1 (20 Hz - 20 kHz) @ 0 Ω source resistance -134 dB / 135.7 dB A-weighted @ 50 Ω source resistance -131 dB / 133.3 dB A-weighted @ 150 Ω source resistance -129 dB / 130.5 dB A-weighted Frequency response 4.
Specifications Mono inputs Microphone inputs (XENYX Mic preamp) Type XLR connector, electronically balanced, discrete input circuit Mic E.I.N.1 (20 Hz - 20 kHz) @ 0 Ω source resistance -134 dB / 135.7 dB A-weighted @ 50 Ω source resistance -131 dB / 133.3 dB A-weighted @ 150 Ω source resistance -129 dB / 130.5 dB A-weighted Frequency response 4.