Manual
Page 6
... source their signals via the XLR connector and also features switchable +48 V phantom power supply for the signals fed in chapter 5.3. ◊ Unlike the X2442USB, the X1622USB, X1832USB and X2222USB have a 3-band equalizer with semi-parametric mid bands. The CLIP display should always be sent to PFL (LEVEL SET)....line input and shows its perceived loudness. The second value range (+10 to -40 dB) refers to adjust the input gain. In the latter case, the effects return can use with st andard line-level signals (-10 dBV or +4 dBu) look like this: While the GAIN control is ...
... source their signals via the XLR connector and also features switchable +48 V phantom power supply for the signals fed in chapter 5.3. ◊ Unlike the X2442USB, the X1622USB, X1832USB and X2222USB have a 3-band equalizer with semi-parametric mid bands. The CLIP display should always be sent to PFL (LEVEL SET)....line input and shows its perceived loudness. The second value range (+10 to -40 dB) refers to adjust the input gain. In the latter case, the effects return can use with st andard line-level signals (-10 dBV or +4 dBu) look like this: While the GAIN control is ...
Manual
Page 7
...signal to a channel signal without affecting the main output signal. The stereo channels are generally pre-fader, i.e. If this were not the case, the effects signal of the channel would remain audible even when the channel fader is turned all the way down , the associated aux ... The panorama and routing controls and the channel fader PAN The PAN control determines the position of the channel signal within the stereo image. The X2442USB has 4 subgroups (1-2 and 3-4). The channel fader determines the channel's volume in mono. MUTE The MUTE switch breaks the signal path pre-channel ...
...signal to a channel signal without affecting the main output signal. The stereo channels are generally pre-fader, i.e. If this were not the case, the effects signal of the channel would remain audible even when the channel fader is turned all the way down , the associated aux ... The panorama and routing controls and the channel fader PAN The PAN control determines the position of the channel signal within the stereo image. The X2442USB has 4 subgroups (1-2 and 3-4). The channel fader determines the channel's volume in mono. MUTE The MUTE switch breaks the signal path pre-channel ...
Manual
Page 12
... characteristic. If the PAN control is pressed, all . A channel's position in Place), audio signals from these outputs and the level meter. X2442USB Fig. 2.18: Subgroup and main mix fader 3. This ensures that channel increases by the level meters. X1832USB Fig. 3.1: The graphic stereo ...level, irrespective of the channel pan controls, the aux sends and the stereo line inputs. For this ¼" stereo jack (X2442USB: 2 phones jacks). In the latter case, the submix is always at the corresponding subgroup outputs. As soon as a rule, taken post-fader. ◊ The ...
... characteristic. If the PAN control is pressed, all . A channel's position in Place), audio signals from these outputs and the level meter. X2442USB Fig. 2.18: Subgroup and main mix fader 3. This ensures that channel increases by the level meters. X1832USB Fig. 3.1: The graphic stereo ...level, irrespective of the channel pan controls, the aux sends and the stereo line inputs. For this ¼" stereo jack (X2442USB: 2 phones jacks). In the latter case, the submix is always at the corresponding subgroup outputs. As soon as a rule, taken post-fader. ◊ The ...
Manual
Page 14
..., but we recommend that the plug is inserted into a free USB port on the complete signal. ring = return input). In case of the X2442USB (1 each subgroup with dynamic processors or equalizers. Insert points are about to the main mix with mono phone plugs on the tape ... microphones can also be used for recording if several tracks simultaneously. In this case, aux send paths are located on or near the rack. ◊ Attention: The POWER switch does not fully disconnect the unit from behringer.com. 5.6 Voltage supply, phantom power supply and fuse X1622USB Fig. 5.3: ...
..., but we recommend that the plug is inserted into a free USB port on the complete signal. ring = return input). In case of the X2442USB (1 each subgroup with dynamic processors or equalizers. Insert points are about to the main mix with mono phone plugs on the tape ... microphones can also be used for recording if several tracks simultaneously. In this case, aux send paths are located on or near the rack. ◊ Attention: The POWER switch does not fully disconnect the unit from behringer.com. 5.6 Voltage supply, phantom power supply and fuse X1622USB Fig. 5.3: ...
Manual
Page 15
15 XENYX X2442USB/X2222USB/X1832USB/X1622USB User Manual SERIAL NUMBER Please note the important information on the side panels of balanced and unbalanced plugs, ring and sleeve have ... ring cold (-ve) tip hot (+ve) For connection of the console. Then, use stereo plugs to link the ring and shaft (or pins 1 & 3 in the case of these screws to fasten the two rack mounts, each specifically to remove the screws holding the left and right side panels. Unbalanced ¼" TS...
15 XENYX X2442USB/X2222USB/X1832USB/X1622USB User Manual SERIAL NUMBER Please note the important information on the side panels of balanced and unbalanced plugs, ring and sleeve have ... ring cold (-ve) tip hot (+ve) For connection of the console. Then, use stereo plugs to link the ring and shaft (or pins 1 & 3 in the case of these screws to fasten the two rack mounts, each specifically to remove the screws holding the left and right side panels. Unbalanced ¼" TS...