Acer P215 Support and Manuals
Popular Acer P215 Manual Pages
User Manual - Page 1
TABLE OF CONTENTS
Special notes on LCD monitors 1 Information for your safety and comfort 2 Unpacking 5 Attaching/Removing the base 6 Screen position adjustment 6 Connecting the power cord 7 Safety precaution 7 Cleaning your monitor 7 Power saving 8 DDC 8 Connector Pin Assignment 9 Standard Timing Table 11 Installation 12 User controls 13 Troubleshooting 19
User Manual - Page 2
...183; Due to make sure the flicker disappears.
· You may flicker during initial use .
· The LCD screen has effective pixels of the fluorescent light, the screen may find slightly uneven brightness on the screen depending on .... EN-1
Turn off the Power Switch for hours. SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a problem.
User Manual - Page 4
... has no effect on your company's
health and safety department.
LCD Pixel Statement
The LCD unit is damaged, cut or frayed
•
liquid was spilled...Users are covered by adjusting the viewing angle of the monitor, using a footrest,
or raising your comfort zone by the operating instructions, since improper adjustment of physical injury. Product servicing
Do not attempt to service...
User Manual - Page 6
... box, and save the packing materials in case you will need to ship or transport the monitor in future.
· LCD Monitor
· AC Power Cord
· D-Sub Cable
· DVI Cable (Only Dual-Input Model)
· Audio Cable (Only Audio-Input
Model)
·
(Optional)
User Manual
P/N:MU.LHR00.001
P215H
2009
EN-5
· Quick Start Guide
P215H LCD monitor
Quick Start...
User Manual - Page 8
...monitor in a place where there is fragile.
No user-adjustment is required.
· Plug one end of the power cord to the AC Inlet, plug another end to a proper AC outlet.
· For unit using at 120 V AC: Use a UL Listed Cord Set... V AC (outside of U.S.): Use a Cord Set consisting of the monitor. SAFETY PRECAUTION
· Avoid placing the monitor, or any other light sources may reflect on ...
User Manual - Page 9
... and corresponding timing. EN-8 DDC
To make your system also supports DDC protocol. The recovery time from the display controller, as indicated by the control signal from Active OFF state back to Plug and Play with your system if your installation easier, the monitor is able to ON state is around 3 seconds. Power...
User Manual - Page 10
...Clock+
12 TMDS Clock-
14 Reserved (N.C. on device)
16 SDA
18 +5V Power
* only for certain models
EN-9
Description
1 TMDS Data2+
3 TMDS Data2-
5 TMDS Data1 Shield
7 TMDS Data0+
9 TMDS Data0-...15 SCL
17 DDC/CEC Ground
19 Hot Plug Detect
PIN No. DESCRIPTION +5V
Logic Ground Monitor Ground DDC-Serial Data
H-Sync V-Sync DDC-Serial Clock
19-pin color display signal cable*
1917151311 9 7...
User Manual - Page 13
... as given below: Steps 1. 1-1 Connect Video Cable
a. b. Power-ON Monitor and Computer Power-ON the monitor first, then power-ON the computer. INSTALLATION
To install the monitor to the computer. 1-2 Digital Cable (Only Dual-Input Model) a. If the monitor still does not function properly, please refer to the troubleshooting section to the computer's port. 2. Make sure both the...
User Manual - Page 14
... VGA or DVI or HDMI If either VGA or DVI input is used to open the Acer eColor Management OSD and access the scenario modes. Using the Shortcut Menu
Press the function button to set the HPos, VPos, Clock and Focus. USER CONTROLS
Power Switch / Power LED: To turn the monitor ON or OFF.
User Manual - Page 15
....
N/A
Movie mode
Displays scenes in unsuitably-lit environments. Settings can be fine-tuned to confirm the mode and exit the eColor menu. Acer eColor Management
Operation instructions
Step 1: Press " " Key to open the Acer eColor Management OSD and access the scenario modes
Step 2: ...and Benefits
Main Menu icon
Sub Menu icon
Sub Menu item
Description
N/A
User mode
User defined.
User Manual - Page 16
... refer to following content is for adjusting the settings of your LCD Monitor. EN-15 Then navigate to
the picture element you wish to adjust. 3 Use ...OSD to open the OSD. Press the MENU key to adjust the picture quality, OSD position and general settings. Adjusting the OSD settings
Note: The following page: Adjusting the picture quality
1 Press the MENU key to adjust the current Brightness...
User Manual - Page 20
... for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem.
(VGA Mode)
Problems
Current Status Remedy
LED ON
· Using OSD, adjust brightness and contrast to maximum or reset to the monitor.
shift, or too
POSITION with the host PC is connected.
· Check if the volume setup of...
User Manual - Page 21
... if AC power cord is properly connected to their default settings. LED displays amber color
· Check if video signal cable is properly connected at the back of monitor.
· Check if the power of the host PC is ON.
(DVI/HDMI mode)
Problems Current Status Remedy
LED ON
· Using OSD, adjust...
User Manual - Page 22
...Rd., Hsichih, Taipei Hsien 221, Taiwan
Contact Person: Mr. Easy Lai, E-mail: easy_lai@acer.com.tw
And, Acer Europe SA
Via Cantonale, Centro Galleria 2 6928 Manno Switzerland
Hereby declare that: Product: Trade Name: Model Number: Series Model Type: SKU Number:
LCD Monitor Acer P215H
P215Hxxxx ("x" = 0~9, a ~ z, or A ~ Z)
Is compliant with the essential requirements and other relevant provisions...
User Manual - Page 23
...of Conformity
This device complies with Part 15 of Responsible Party: 333 West San Carlos St. A.
Contact Person:
Acer Representative
Phone No.:
254-298-...harmful interference, and (2) this declaration:
Product Name: Main Model Number: Series Model Number:
21.5"W LCD Monitor P215Hxxxx P215Hxxxx
Name of Responsible Party: Acer America Corporation
Address of the FCC Rules. San Jose, ...
Acer P215 Reviews
Do you have an experience with the Acer P215 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Acer yet.
Earn 750 points for your review!