Owner's Manual
Page 154
... at a slower cruising speed, press repeatedly or hold push down the "RES +/ SET -" switch (3) until the vehicle has slowed to detect obstacles near the rear bumper. When you by an obstacle.
... at a slower cruising speed, press repeatedly or hold push down the "RES +/ SET -" switch (3) until the vehicle has slowed to detect obstacles near the rear bumper. When you by an obstacle.
Owner's Manual
Page 155
...into the garage or moving within a limited speed range. NOTE: • If the bumper hits a hard object, the sensors on the information display. If this occurs, have the sensors inspected by an authorized SUZUKI dealer. • An obstacle within a limited area and only when the vehicle is...detect obstacles only within about 1.5 m (5 ft) from a sensor or just below a sensor is in the ON position. Sensor Locations On rear bumper Approximate Areas Where Obstacles Can Be Detected WARNING • The parking sensor warns you the location of the obstacles on it using your direct vision...
...into the garage or moving within a limited speed range. NOTE: • If the bumper hits a hard object, the sensors on the information display. If this occurs, have the sensors inspected by an authorized SUZUKI dealer. • An obstacle within a limited area and only when the vehicle is...detect obstacles only within about 1.5 m (5 ft) from a sensor or just below a sensor is in the ON position. Sensor Locations On rear bumper Approximate Areas Where Obstacles Can Be Detected WARNING • The parking sensor warns you the location of the obstacles on it using your direct vision...
Owner's Manual
Page 156
OPERATING YOUR VEHICLE CAUTION • Under the following types of obstacles: - Objects made of the bumper is changed due to alteration to the suspension or other causes. - The sensor areas are extremely hot from direct sunlight or cold due to a highly... ropes - Square-shaped curbstones or other objects with sharp edges - Tall objects with Canadian ICES*-001 * Interference-Causing Equipment Standards 3-25 are installed on the bumper. - The height of a thin material like a road sign - Low-profile objects such as curbstones - Sound-absorbing objects such as cotton and snow NOTE: • ...
OPERATING YOUR VEHICLE CAUTION • Under the following types of obstacles: - Objects made of the bumper is changed due to alteration to the suspension or other causes. - The sensor areas are extremely hot from direct sunlight or cold due to a highly... ropes - Square-shaped curbstones or other objects with sharp edges - Tall objects with Canadian ICES*-001 * Interference-Causing Equipment Standards 3-25 are installed on the bumper. - The height of a thin material like a road sign - Low-profile objects such as curbstones - Sound-absorbing objects such as cotton and snow NOTE: • ...
Owner's Manual
Page 255
... back to the holding clip (4). 2) Lower the hood close the engine hood: 1) Lift the hood up the hood until it is high enough to the bumper, then let it drop down.
... back to the holding clip (4). 2) Lower the hood close the engine hood: 1) Lift the hood up the hood until it is high enough to the bumper, then let it drop down.
Owner's Manual
Page 272
.... • For vehicles with roof rack anchors, make sure that people and objects are covered with any garage door opener that they hang over the bumpers or the sides of the vehicle, or block your view. • Secure the front and rear ends of long items - such as gate operators, garage...
.... • For vehicles with roof rack anchors, make sure that people and objects are covered with any garage door opener that they hang over the bumpers or the sides of the vehicle, or block your view. • Secure the front and rear ends of long items - such as gate operators, garage...
Owner's Manual
Page 336
To facilitate bulb replacement, turn off the engine. 57L70041 (2) (2) (2) 57L70040 4) Remove the part of the bumper (3) indicated in reverse to be replaced, then turn the steering wheel away from the side marker light whose bulb is to restore the original state. 2) ...
To facilitate bulb replacement, turn off the engine. 57L70041 (2) (2) (2) 57L70040 4) Remove the part of the bumper (3) indicated in reverse to be replaced, then turn the steering wheel away from the side marker light whose bulb is to restore the original state. 2) ...
Owner's Manual
Page 337
... bulb, then follow the above steps in reverse to restore the original state. Front turn off the engine. (2) (1) 57L70041 57L70045 4) Remove the part of the bumper (3) indicated in the illustration. 3) Open the indicated end of the cover on the inside of the fender and remove the bulb socket (2) by twisting the...
... bulb, then follow the above steps in reverse to restore the original state. Front turn off the engine. (2) (1) 57L70041 57L70045 4) Remove the part of the bumper (3) indicated in the illustration. 3) Open the indicated end of the cover on the inside of the fender and remove the bulb socket (2) by twisting the...