Owner's Manual
Page 159
... ROD 4-cylinder models 6-cylinder models 3. Lift the hood up most of the way and hold it up slightly to about a foot (30 cm) above the fender, then let it is securely latched. The hydraulic supports will lift it up the rest of the way. CONTINUED Before Driving Service Station Procedures To...
... ROD 4-cylinder models 6-cylinder models 3. Lift the hood up most of the way and hold it up slightly to about a foot (30 cm) above the fender, then let it is securely latched. The hydraulic supports will lift it up the rest of the way. CONTINUED Before Driving Service Station Procedures To...
Owner's Manual
Page 160
Service Station Procedures To close the hood, lower it is securely latched. Wait a few minutes after turning the engine off before you fill the car with your hands. Oil Check 4-cylinder models DIPSTICK 6-cylinder models DIPSTICK Check the engine oil level every time you check the oil. 1. Before Driving Remove the dipstick (orange handle). After closing the hood, make sure it to about a foot (30 cm) above the fender, then press down firmly with fuel.
Service Station Procedures To close the hood, lower it is securely latched. Wait a few minutes after turning the engine off before you fill the car with your hands. Oil Check 4-cylinder models DIPSTICK 6-cylinder models DIPSTICK Check the engine oil level every time you check the oil. 1. Before Driving Remove the dipstick (orange handle). After closing the hood, make sure it to about a foot (30 cm) above the fender, then press down firmly with fuel.
Owner's Manual
Page 252
... by turning it in place. 7. Install the new bulb in place. Test the lights to the left. 2. Remove the burned out bulb from the inner fender. 3. If you are changing the bulb on the passenger's side, turn counterclockwise. 9. Lock it unlocks. 6. Maintenance Pull the inner...assembly by pushing on the driver's side, start the engine, turn off the engine. Put the inner fender in the socket. If you are changing the bulb on the center. Remove the socket from the fender and bumper. 4. Use a flat-tipped screwdriver to the right, and turn the steering wheel all the...
... by turning it in place. 7. Install the new bulb in place. Test the lights to the left. 2. Remove the burned out bulb from the inner fender. 3. If you are changing the bulb on the passenger's side, turn counterclockwise. 9. Lock it unlocks. 6. Maintenance Pull the inner...assembly by pushing on the driver's side, start the engine, turn off the engine. Put the inner fender in the socket. If you are changing the bulb on the center. Remove the socket from the fender and bumper. 4. Use a flat-tipped screwdriver to the right, and turn the steering wheel all the...
Owner's Manual
Page 254
... the edge of the trunk lining by turning it clockwise until it is working. 7. Make sure it bottoms. 5. Open the trunk. Put the fastener in Fenders) 4. Determine which of its socket. Lights Replacing Rear Bulbs (in the hole on the side of the trunk lining and push on the side of...
... the edge of the trunk lining by turning it clockwise until it is working. 7. Make sure it bottoms. 5. Open the trunk. Put the fastener in Fenders) 4. Determine which of its socket. Lights Replacing Rear Bulbs (in the hole on the side of the trunk lining and push on the side of...
Owner's Manual
Page 271
Turn the jack's end bracket counterclockwise to loosen it, then remove the jack. 8. Changing a Flat Tire WHEEL NUTS JACK 6. Remove the cover by turning the handle counterclockwise, then pulling on the cover. 7. Loosen the four wheel nuts (4cylinder) or five (V-6) 1/2 turn with the wheel wrench. Taking Care of the Unexpected The jack is behind a cover in the right fender.
Turn the jack's end bracket counterclockwise to loosen it, then remove the jack. 8. Changing a Flat Tire WHEEL NUTS JACK 6. Remove the cover by turning the handle counterclockwise, then pulling on the cover. 7. Loosen the four wheel nuts (4cylinder) or five (V-6) 1/2 turn with the wheel wrench. Taking Care of the Unexpected The jack is behind a cover in the right fender.