Stihl MS 193 T Support Question
Stihl MS 193 T Support Question
Find answers below for this question about Stihl MS 193 T.Need a Stihl MS 193 T manual? We have 1 online manual for this item!
Question posted by Koberhausllc on October 24th, 2017
I Have To Choke It To Start It It Revs High For About 10 Seconds Then Dies Out
I was told I have a float that is sticking and looking at the schematic I don't see a float PR they are calling it by a different name
Current Answers
Answer #1: Posted by techyagent on October 25th, 2017 6:19 AM
techyagent
Member since:
June 17th, 2014 Points: 4,799,780
Member since:
June 17th, 2014 Points: 4,799,780
First thing I'd do is change the gas filter on the end of suction hose in gas tank. You can fish it out w/ a small hook formed in the end of a piece of tie wire.
If that doesn't cure it,then check gas line closely for small cracks. If none,then it has carb problems:debris in gas control needle,cracked diaphragm.
If that doesn't cure it,then check gas line closely for small cracks. If none,then it has carb problems:debris in gas control needle,cracked diaphragm.
Please check the link below for reference
http://forums2.gardenweb.com/discussions/1629422/stihl-chainsaw-starts-but-wont-run
Techygirl
Related Stihl MS 193 T Manual Pages
Product Instruction Manual - Page 3
...Working Techniques" before using your STIHL chain saw,
50
it is a high-speed wood-cutting tool, some special safety precautions must be recycled. Guide...Chain Oil Tank
30
Checking Chain Lubrication
31
Chain Brake
31
Starting / Stopping the Engine
32
Operating Instructions
36
Taking Care of ...Trademarks
{
MS 170, MS 170 C, MS 180, MS 180 C
Allow only persons who fully understand 42 this...
Product Instruction Manual - Page 5
...
Warning! Most of Federal Regulations 1910.266.
If you have
English
different parts and controls. Warning! Read the instruction manual and the safety instructions...take a break. Safety Precautions and Working Techniques
Because a chain saw is a high-speed, fast-cutting power tool, special safety precautions must be aggravated by strenuous work...MS 170, MS 170 C, MS 180, MS 180 C
3
Product Instruction Manual - Page 8
Check for fueling and move at least 10 feet (3 m) from the fueling spot before starting the engine. Different models may be damaged or broken;
Such misalignment can result...been wiped away. Fold the grip flush with the raised positioning
6
MS 170, MS 170 C, MS 180, MS 180 C If the grip does not lie completely flush with different fuel caps. N If your cap still does not tighten properly, it...
Product Instruction Manual - Page 9
... the handles clean and dry at least 10 feet (3 m) from the fueling spot, outdoors only.
Start and operate your Instruction Manual for proper condition and operation. (See the maintenance chart near the end of fire and burn injuries, start the saw without assistance. MS 170, MS 170 C, MS 180, MS 180 C
7
The throttle trigger must be used...
Product Instruction Manual - Page 10
... and then give it a brisk, strong pull.
001BA113 KN 001BA114 KN
The second recommended method for starting your instruction manual) and place the chain saw firmly with incorrect idle adjustment....is running cutting tool, do not wrap the starter rope around the handles.
8
MS 170, MS 170 C, MS 180, MS 180 C Keep your power tool and make proper adjustments and repairs. Maintain good...
Product Instruction Manual - Page 12
... daylight conditions only. Your chain saw is needed. Keep within calling distance of others in case help is a one-person machine.... in the general work area, even when starting. Working Conditions
Operate and start your body is clear of the cutting attachment... reproductive harm. Warning! Some of dust encountered.
10
MS 170, MS 170 C, MS 180, MS 180 C carbon monoxide) may cause the bar and...
Product Instruction Manual - Page 13
...! A modified or damaged muffler could damage the cutting attachment or AV system. MS 170, MS 170 C, MS 180, MS 180 C
11 Breathing asbestos dust is equipped with a damaged or missing chain catcher...asbestos, immediately contact your power tool using the starting throttle lock, as pine needles, branches or leaves. move for more than a few seconds when the chain is pinched in the cut ...
Product Instruction Manual - Page 16
...
14
MS 170, MS 170 C, MS 180, MS 180 C Never operate your body. In a kickback situation this guard helps protect your instruction manual. In addition, removal of 3 seconds has occurred...seconds when the chain brake is engaged or when the chain is pinched or otherwise caught in higher kickback tendency. If clutch slippage in excess of the hand guard on the packaging are sufficiently high...
Product Instruction Manual - Page 18
...you or pull you are not experienced with these cutting techniques.
10. Do not cut .
9. Be especially careful near wire ...cause the cut because the chain can pinch.
16
MS 170, MS 170 C, MS 180, MS 180 C Low kickback chain will not significantly reduce ...-in
A
Pull-in occurs when the chain on a bow guide. Always start a cut more than one log at full throttle.
7. English
Bow Guides
...
Product Instruction Manual - Page 30
..., first remove the container from static
28
MS 170, MS 170 C, MS 180, MS 180 C Take care when handling gasoline. Use...mixture of the fuel is specially formulated for use only high-quality unleaded gasoline! Avoid direct contact with a lower octane... against
the underside of 89 (R+M/2) and no more often than 10% ethanol content. Some fuel additives not only detrimentally affect elastomers ...
Product Instruction Manual - Page 33
...is when you check operation of oil. during a
MS 170, MS 170 C, MS 180, MS 180 C
31 Every new chain has to be...very short time. Always disengage chain brake before accelerating engine and before starting work . even if your saw chain must always throw off a... lubrication and the oil level in certain kickback situations.
High revs with chain brake
143BA024 KN 143BA011 KN
143BA012 KN
The...
Product Instruction Manual - Page 34
...32
MS 170, MS 170 C, MS 180, MS 180 C Chain brake maintenance
The chain brake is for starting the warm engine - It is squeezed Cold start l - To set the master control lever to cold start ... throttle for the first time
- Position cold start n
- When the engine has turned over for no more than 3 seconds - Accelerate up to the warm start l position. ignition is only possible from dirt...
Product Instruction Manual - Page 36
... stores the energy for approx. N For this reason, a few seconds may pass between the pulling of the starter rope and the starting ) Position warm start n - the saw
34
MS 170, MS 170 C, MS 180, MS 180 C If engine is warm (once the engine has been running for starting procedure
143BA016 KN 143BA017 KN
For all the way -
do...
Product Instruction Manual - Page 38
...Chain".
Always slacken off , it again. see "Adjusting the Carburetor". Running the engine at high revs with a full tank of the bar -
After a long period of full-throttle operation
After a... flow of cooling air.
Long-term storage
See "Storing the machine"
36
MS 170, MS 170 C, MS 180, MS 180 C This protects enginemounted components (ignition, carburetor) from sources of full-...
Product Instruction Manual - Page 48
...starting...Visual inspection (condition, leaks) Clean
Throttle trigger, throttle trigger lockout, choke lever, stop switch, Master Control lever (depending Check operation on ...X
XX
X
X
X
X
X
X
X
X
X
X
X
XX
X
X
X
X
X
X
X
MS 170, MS 170 C, MS 180, MS 180 C If you only use the saw occasionally, extend the intervals accordingly. English
Maintenance and Care
The following maintenance...
Product Instruction Manual - Page 49
... X
X
X X
MS 170, MS 170 C, MS 180, MS 180 C
47 If your daily ...10 to 20 hours of professional saws (3.4 kW or more) after each refueling stop weekly monthly every 12 months if problem if damaged if required
Cooling inlets
Clean
X
Cylinder fins
Clean
X
X
Carburetor
Check idle adjustment - If you only use the saw occasionally, extend the intervals accordingly. English
before starting...
Product Instruction Manual - Page 51
... Front Chain Tensioner Permits precise adjustment of chain tension.
10 Guide Bar Supports and guides the saw chain.
11 ...brake activation.
17 Front Handle (Handlebar) Handlebar for choke control, starting throttle, run and stop switch position.
21 Fuel ...designed to the operator's hands. (not illustrated)
MS 170, MS 170 C, MS 180, MS 180 C
49 Spark arresting screen is accelerated beyond ...
Product Instruction Manual - Page 56
...emission test. STIHL Incorporated is liable for required maintenance at an authorized STIHL servicing dealer. Choke (Cold Start Enrichment System)
- Intake Manifold
-
Fuel Pump
- Spark Plug
- Any warranted part which...shall be performed at and after the first scheduled replacement point.
54
MS 170, MS 170 C, MS 180, MS 180 C Any such work will be used for Warranty Service
Bring ...
Product Instruction Manual - Page 57
...not to a STIHL servicing dealer as soon as :
Air Filter, Carburetor, Fuel Pump, Choke (Cold Start Enrichment System), Control Linkages, Intake Manifold, Magneto or Electronic Ignition System (Ignition Module), Spark.... The warranty repairs should however be liable to the owner. MS 170, MS 170 C, MS 180, MS 180 C
55 STIHL Incorporated California Exhaust and Evaporative Emissions Control ...
Product Instruction Manual - Page 58
... on emission-related parts and must be warranted for warranty coverage.
56
MS 170, MS 170 C, MS 180, MS 180 C Any warranted part that part. Any warranted part that such ... or replaced under warranty. Emission Warranty Parts List
Air Filter, Carburetor, Fuel Pump, Choke (Cold Start Enrichment System), Control Linkages, Intake Manifold, Magneto or Electronic Ignition System (Ignition Module),...
Similar Questions
Br 700 X Leaf Blower Stops Running After 10 Minutes
My Stihl br 700 X leafblower will run for about 10 minutes at full throttle then bog down and quit. ...
My Stihl br 700 X leafblower will run for about 10 minutes at full throttle then bog down and quit. ...
(Posted by RichmondJimA 2 years ago)
Br450 Electric Start Issue
On my BR450, when pushing the button I get about 2 attempts at starting and then nothing. Is it a Ba...
On my BR450, when pushing the button I get about 2 attempts at starting and then nothing. Is it a Ba...
(Posted by 12jokerzz 2 years ago)
No Throttle
I just bought a stihl wood boss 251, back pack blower and tiller slash weed water. I've only used th...
I just bought a stihl wood boss 251, back pack blower and tiller slash weed water. I've only used th...
(Posted by Jtamme937 2 years ago)
Part No For Stihl Km90r On/of Switch
i require 1 new on/of switch for my stihl km90r want part no or where it can be purchased its orange...
i require 1 new on/of switch for my stihl km90r want part no or where it can be purchased its orange...
(Posted by johnnash222 8 years ago)
